1. INSPECTION AFTER COLLISION
Inspect the SRS parts in the table below.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Be sure to correctly follow the removal and installation procedures for the SRS parts.
If there is any damage or deformation of airbag installation components or the areas they are installed to, do not attempt to repair them. Replace the damaged components with new ones.
| Component to Inspect | Procedure |
|---|---|
| Horn button assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the horn button assembly removed from the vehicle.
If any defects are found, replace the horn button assembly or steering wheel assembly with a new one. |
| Lower No. 1 instrument panel airbag assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the lower No. 1 instrument panel airbag assembly removed from the vehicle.
If any defects are found, replace the lower No. 1 instrument panel airbag assembly, No. 1 instrument panel brace sub-assembly, lower instrument panel mounting bracket or instrument panel reinforcement assembly with a new one. |
| Lower No. 2 instrument panel airbag assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the lower No. 2 instrument panel airbag assembly removed from the vehicle.
If any defects are found, replace the lower No. 2 instrument panel airbag assembly, No. 2 instrument panel brace sub-assembly or lower instrument panel mounting bracket with a new one. |
| Instrument panel passenger airbag assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the instrument panel passenger airbag assembly removed from the vehicle.
If any defects are found, replace the instrument panel passenger airbag assembly, instrument panel safety pad assembly or instrument panel reinforcement assembly with a new one. |
| Curtain shield airbag assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the curtain shield airbag assemblies removed from the vehicle.
If any defects are found, replace the curtain shield airbag assembly with a new one. |
| Front seat airbag assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the front seat airbag assemblies installed to the vehicle.
If any defects are found, replace the front seatback frame sub-assembly, front seatback pad or front seatback cover sub-assembly with a new one.
3.
Visually check for defects with the front seat airbag assemblies removed from the vehicle.
If any defects are found, replace the front seat airbag assembly with a new one. |
| Rear seat airbag assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the rear seat airbag assemblies removed from the vehicle.
If any defects are found, replace the rear seat airbag assembly, rear seatback frame, No. 1 seatback pad or No. 1 seatback cover sub-assembly with a new one. |
| Front seat outer belt assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the front seat outer belt assembly removed from the vehicle.
If any defects are found, replace the front seat outer belt assembly with a new one. |
| Rear No. 1 seat outer belt assembly |
1.
Perform a diagnostic system check.
2.
Visually check for defects with the rear No. 1 seat outer belt assembly removed from the vehicle.
If any defects are found, replace the rear No. 1 seat outer belt assembly with a new one. |
| Airbag sensor with ECU assembly |
1.
for Airbag that has not Deployed:
(a)
Perform a diagnostic system check.
(b)
Visually check for defects with the airbag sensor with ECU assembly installed to the vehicle.
If any defects are found, replace the airbag sensor with ECU assembly with a new one.
2.
for Airbag that has Deployed:
(a)
Replace the airbag sensor with ECU assembly.
|
| Front airbag sensor |
1.
When airbags have deployed as the result of a collision, be sure to replace all airbag sensors in the damaged areas (anywhere in need of repair).
2.
Visually check the airbag sensors in undamaged areas for defects.
If any defects are found or an airbag sensor has detected a major collision, replace the airbag sensor with a new one.
3.
Perform a diagnostic system check. |
| Side airbag pressure sensor | |
| Floor side airbag sensor | |
| No. 2 side airbag sensor assembly | |
| Rear floor side airbag sensor | |
| Harness and connector |
1.
Perform a diagnostic system check.
2.
Check any wire harnesses in exposed contact with the airbag wire harness for damage.
3.
Check the connector of the airbag wire harness for scratches, cracks or damage. |