Home › Vehicle Interior › HEATING / AIR CONDITIONING › ROOM TEMPERATURE SENSOR (for Rear Side)
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467919 ROOM TEMPERATURE SENSOR(for Rear Side) G

HEATING / AIR CONDITIONING  ROOM TEMPERATURE SENSOR(for Rear Side)  INSPECTION  


PROCEDURE

Hide 88625U 1.INSPECT COOLER THERMISTOR (DUCT SENSOR) (for LH Side)

a.
E465124C01
0.948,0.135 1.271,0.333 0.323,0.198 1.656,3.375 1.979,3.063 false 1.521,1.594 1.719,1.448 false 0.208,0.188 0.521,0.344 0.313,0.156 10 false *a 0.094,3 0.406,3.156 0.313,0.156 10 false *c 1.771,4.469 2.083,4.625 0.313,0.156 10 false *d 1.99,2.906 2.302,3.063 0.313,0.156 10 false *e 0.958,4.333 1.25,4.552 0.292,0.219 10 false (68) 0.469,4.333 0.76,4.552 0.292,0.219 10 false (50) 1.479,4.333 1.771,4.552 0.292,0.219 10 false (86) 1.979,4.323 2.354,4.573 0.375,0.25 10 false (104) 2.49,4.333 2.865,4.583 0.375,0.25 10 false (122) 3,4.333 3.333,4.583 0.333,0.25 10 false (140) 1.021,0.156 1.479,0.354 0.458,0.198 10 false U1 0.323,2.115 0.635,2.271 0.313,0.156 10 false 3.5 0.333,1.833 0.646,1.99 0.313,0.156 10 false 4.0 0.313,2.396 0.625,2.552 0.313,0.156 10 false 3.0 0.313,2.667 0.625,2.823 0.313,0.156 10 false 2.5 0.313,2.958 0.625,3.115 0.313,0.156 10 false 2.0 0.313,3.24 0.625,3.396 0.313,0.156 10 false 1.5 0.313,3.51 0.625,3.667 0.313,0.156 10 false 1.0 0.302,3.781 0.615,3.938 0.313,0.156 10 false 0.5 0.313,4.063 0.625,4.219 0.313,0.156 10 false 0.0 0.5,4.188 0.813,4.344 0.313,0.156 10 false 10 1,4.188 1.292,4.406 0.292,0.219 10 false 20 1.51,4.188 1.802,4.406 0.292,0.219 10 false 30 2.052,4.177 2.344,4.396 0.292,0.219 10 false 40 2.573,4.188 2.865,4.406 0.292,0.219 10 false 50 3.094,4.188 3.333,4.406 0.24,0.219 10 false 60 1.365,1.563 1.677,1.719 0.313,0.156 10 false *b
*a Component without harness connected
(Cooler Thermistor (Duct Sensor))
*b Sensing Portion
*c Resistance (kΩ)
*d Temperature (°C (°F))
*e Allowable Range


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(U1)Location & Routing

Click Connector(U1)Body>No. 2 Room Wire>Cooler (Room Temperature Sensor) Thermistor Rear LH

U1-1 - U1-2 10°C (50°F) 3.00 to 3.73 kΩ
U1-1 - U1-2 15°C (59°F) 2.45 to 2.88 kΩ
U1-1 - U1-2 20°C (68°F) 1.95 to 2.30 kΩ
U1-1 - U1-2 25°C (77°F) 1.60 to 1.80 kΩ
U1-1 - U1-2 30°C (86°F) 1.28 to 1.47 kΩ
U1-1 - U1-2 35°C (95°F) 1.00 to 1.22 kΩ
U1-1 - U1-2 40°C (104°F) 0.80 to 1.00 kΩ
U1-1 - U1-2 45°C (113°F) 0.65 to 0.85 kΩ
U1-1 - U1-2 50°C (122°F) 0.50 to 0.70 kΩ
U1-1 - U1-2 55°C (131°F) 0.44 to 0.60 kΩ
U1-1 - U1-2 60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Perform the inspection without removing the cooler thermistor (duct sensor) from the quarter trim panel assembly.

·

Do not connect the connector without the cooler thermistor (duct sensor) installed to the quarter trim panel assembly to prevent the cooler thermistor (duct sensor) terminal from being disconnected.

·

Hold the sensor only by its connector. Touching the sensing portion may change the resistance value.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).


If the result is not as specified, replace the cooler thermistor (duct sensor).



Hide 88625U 2.INSPECT COOLER THERMISTOR (DUCT SENSOR) (for RH Side)

a.
E465124C02
0.813,0.104 1.135,0.302 0.323,0.198 1.688,3.354 1.958,3 false 1.583,1.615 1.729,1.458 false 0.208,0.188 0.521,0.344 0.313,0.156 10 false *a 0.094,3 0.406,3.156 0.313,0.156 10 false *c 1.781,4.448 2.094,4.604 0.313,0.156 10 false *d 1.979,2.875 2.292,3.031 0.313,0.156 10 false *e 0.969,4.333 1.26,4.552 0.292,0.219 10 false (68) 0.469,4.333 0.76,4.552 0.292,0.219 10 false (50) 1.49,4.333 1.781,4.552 0.292,0.219 10 false (86) 1.979,4.333 2.354,4.583 0.375,0.25 10 false (104) 2.51,4.333 2.885,4.583 0.375,0.25 10 false (122) 3,4.333 3.333,4.583 0.333,0.25 10 false (140) 0.906,0.125 1.365,0.323 0.458,0.198 10 false R1 0.313,2.125 0.625,2.281 0.313,0.156 10 false 3.5 0.313,1.854 0.625,2.01 0.313,0.156 10 false 4.0 0.313,2.396 0.625,2.552 0.313,0.156 10 false 3.0 0.313,2.688 0.625,2.844 0.313,0.156 10 false 2.5 0.313,2.969 0.625,3.125 0.313,0.156 10 false 2.0 0.313,3.25 0.625,3.406 0.313,0.156 10 false 1.5 0.313,3.521 0.625,3.677 0.313,0.156 10 false 1.0 0.302,3.792 0.615,3.948 0.313,0.156 10 false 0.5 0.313,4.052 0.625,4.208 0.313,0.156 10 false 0.0 0.49,4.177 0.802,4.333 0.313,0.156 10 false 10 0.99,4.167 1.281,4.385 0.292,0.219 10 false 20 1.521,4.167 1.813,4.385 0.292,0.219 10 false 30 2.052,4.167 2.344,4.385 0.292,0.219 10 false 40 2.583,4.167 2.875,4.385 0.292,0.219 10 false 50 3.083,4.167 3.323,4.385 0.24,0.219 10 false 60 1.448,1.625 1.76,1.781 0.313,0.156 10 false *b
*a Component without harness connected
(Cooler Thermistor (Duct Sensor))
*b Sensing Portion
*c Resistance (kΩ)
*d Temperature (°C (°F))
*e Allowable Range


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(R1)Location & Routing

Click Connector(R1)Body>Room Wire>Cooler (Room Temperature Sensor) Thermistor Rear RH

R1-1 - R1-2 10°C (50°F) 3.00 to 3.73 kΩ
R1-1 - R1-2 15°C (59°F) 2.45 to 2.88 kΩ
R1-1 - R1-2 20°C (68°F) 1.95 to 2.30 kΩ
R1-1 - R1-2 25°C (77°F) 1.60 to 1.80 kΩ
R1-1 - R1-2 30°C (86°F) 1.28 to 1.47 kΩ
R1-1 - R1-2 35°C (95°F) 1.00 to 1.22 kΩ
R1-1 - R1-2 40°C (104°F) 0.80 to 1.00 kΩ
R1-1 - R1-2 45°C (113°F) 0.65 to 0.85 kΩ
R1-1 - R1-2 50°C (122°F) 0.50 to 0.70 kΩ
R1-1 - R1-2 55°C (131°F) 0.44 to 0.60 kΩ
R1-1 - R1-2 60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Perform the inspection without removing the cooler thermistor (duct sensor) from the quarter trim panel assembly.

·

Do not connect the connector without the cooler thermistor (duct sensor) installed to the quarter trim panel assembly to prevent the cooler thermistor (duct sensor) terminal from being disconnected.

·

Hold the sensor only by its connector. Touching the sensing portion may change the resistance value.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).


If the result is not as specified, replace the cooler thermistor (duct sensor).