Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E444901N07
0.688,0.5 1.104,0.76 0.417,0.26 2.146,0.49 2.563,0.75 0.417,0.26 3.667,0.479 4.083,0.74 0.417,0.26 5.115,0.469 5.531,0.729 0.417,0.26 6.313,0.469 6.729,0.729 0.417,0.26 6.417,0.542 6.729,0.74 0.313,0.198 10 false z16 5.229,0.542 5.688,0.74 0.458,0.198 10 false I33 3.781,0.552 4.24,0.75 0.458,0.198 10 false I32 2.271,0.563 2.729,0.76 0.458,0.198 10 false I31 0.802,0.563 1.26,0.76 0.458,0.198 10 false I30

a.

Disconnect the I33 and I31*1, *2 air conditioning amplifier assembly connectors.

*1: w/ Rear Cooler

*2: w/ Rear Air Conditioning System



b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition

*1: w/ Rear Cooler

*2: w/ Rear Air Conditioning System

I33-5 (B) - Body ground Power source Always 11 to 14 V
I33-6 (IG+) - Body ground Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
I33-17 (GND) - Body ground Ground Always Below 1 Ω
I31-1 (+B2) - Body ground*1, *2 Power source Always 11 to 14 V
I31-4 (GND2) - Body ground*1, *2 Ground Always Below 1 Ω


c.

Reconnect the I33 and I31*1, *2 air conditioning amplifier assembly connectors.

*1: w/ Rear Cooler

*2: w/ Rear Air Conditioning System



d.

Measure the voltage and resistance and check for pulse according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition

*1: w/ Rear Cooler

*2: w/ Rear Air Conditioning System

*3: w/ Ion Generator

*4: w/ PTC Heater

*5: w/ Condenser Fan

*6: w/ Cooling Box

*7: Value when sensor power source voltage is 5 V

I33-1 (CANL) CAN communication line - -
I33-2 (CANH) CAN communication line - -
I33-3 (ACT) - Body ground Magnet clutch on permit input signal
·

Engine running

·

Blower switch: On (LO level)

·

A/C switch: Off or on (magnet clutch off)


Below 1 V
·

Engine running

·

Blower switch: On (LO level)

·

A/C switch: On (magnet clutch on)


4.5 to 5.5 V
I33-4 (NAIN) - Body ground*3 Ion generator sub-assembly operation condition signal
·

Ignition switch ON

·

Blower switch: On


Below 2.2 V
·

Ignition switch ON

·

Blower switch: Off


4.75 to 5.25 V
I33-7 (LIN1) - Body ground LIN communication signal Ignition switch ON Pulse generation
(See waveform 1)
I33-19 (AC1) - Body ground Idle-up request signal
·

Engine running

·

Blower switch: On (LO level)

·

A/C switch: Off


11 to 14 V
·

Engine running

·

Blower switch: On (LO level)

·

A/C switch: On


Below 1 V
I33-21 (BLW) - Body ground Blower motor speed control signal
·

Ignition switch ON

·

Blower switch: LO


Pulse generation
(See waveform 2)
I33-23 (PTC1) - Body ground*4 Quick heater assembly operation signal
·

Engine running

·

ECO mode switch: Off

·

Temperature settings: MAX HOT

·

Ambient temperature: 25°C (77°F) or lower

·

Engine coolant temperature: 75°C (167°F) or lower

·

Light control switch: Off

·

Blower switch: Off → on (after 10 seconds)


11 to 14 V → Below 1 V
I33-24 (NANO) - Body ground*3 Ion generator sub-assembly operation signal
·

Ignition switch ON

·

Blower switch: On


Below 1 V
·

Ignition switch ON

·

Blower switch: Off


4.75 to 5.25 V
I32-1 (TAM) - Body ground Thermistor assembly (ambient temperature sensor) signal
·

Ignition switch ON

·

Ambient temperature: 25°C (77°F)


1.05 to 1.45 V
·

Ignition switch ON

·

Ambient temperature: 40°C (104°F)


0.64 to 0.87 V
I32-3 (SG-1) - Body ground Ground for sensor Always Below 1 Ω
I32-4 (SG-5) - Body ground*1 Ground for sensor Always Below 1 Ω
I32-5 (TR) - Body ground Cooler thermistor (room temperature sensor) signal
·

Ignition switch ON

·

Cabin temperature: 25°C (77°F)


1.05 to 1.45 V
·

Ignition switch ON

·

Cabin temperature: 40°C (104°F)


0.64 to 0.87 V
I32-6 (PRE) - Body ground Air conditioning pressure sensor signal
·

Engine running

·

Air conditioning system operating

·

Refrigerant pressure: Normal pressure (less than 3025 kPaG (30.8 kgf/cm2, 439 psi) and more than 176 kPaG (1.8 kgf/cm2, 26 psi))


0.62 to 4.73 V*7
I32-7 (BSET) - Body ground*1 Volume switch of cooler control switch assembly signal
·

Ignition switch ON

·

Blower switch: Off → HI


Below 1 → 5.15 V
I32-11 (S5-3) - Body ground Power supply for air conditioning pressure sensor Ignition switch ON 4.75 to 5.25 V
Ignition switch off Below 1 V
I32-12 (LOCK) - Body ground Compressor lock sensor signal
·

Engine running

·

A/C switch: On (magnet clutch on)

·

Blower switch: LO


Pulse generation
(See waveform 3)
I32-13 (S5-2) - Body ground*1 Power supply for cooler control switch assembly
·

Ignition switch ON

·

Blower switch: Off → HI


Below 1 V → 4.85 to 5.15 V
I32-14 (SG-2) - Body ground Ground for sensor Always Below 1 Ω
I32-15 (SG-4) - Body ground Ground for sensor Always Below 1 Ω
I32-16 (PTC2) - Body ground*4 Quick heater assembly operation signal
·

Engine running

·

ECO mode switch: Off

·

Temperature settings: MAX HOT

·

Ambient temperature: 16°C (61°F) or lower

·

Engine coolant temperature: 70°C (158°F) or lower

·

Light control switch: Off

·

Blower switch: Off → on (after 20 seconds)


11 to 14 V → Below 1 V
I32-17 (PTC3) - Body ground*4 Quick heater assembly operation signal
·

Engine running

·

ECO mode switch: Off

·

Temperature settings: MAX HOT

·

Ambient temperature: -7°C (19°F) or lower

·

Engine coolant temperature: 65°C (149°F) or lower

·

Light control switch: Off

·

Blower switch: Off → on (after 30 seconds)


11 to 14 V → Below 1 V
I32-19 (MGC) - Body ground Magnet clutch operation signal
·

Engine running

·

Blower switch: LO

·

A/C switch: On (magnet clutch on)


Below 1 V
·

Engine running

·

Blower switch: LO

·

A/C switch: Off or on (magnet clutch off)


11 to 14 V
I32-20 (CFAN) - Body ground*5 Condenser fan operation signal Ignition switch ON 11 to 14 V
I31-2 (RBBU) - Body ground*2 Power supply for BUS IC (for Rear) Always 11 to 14 V
I31-3 (RBUG) - Body ground*2 Ground for BUS IC (for Rear) Always Below 1 Ω
I31-6 (RMGV) - Body ground*1, *2 Rear cooling unit expansion valve signal
·

Ignition switch ON

·

Blower switch: LO

·

A/C switch: On


11 to 14 V
I31-7 (RBUS) - Body ground*2 BUS IC control signal (for Rear) Ignition switch ON Pulse generation
(see waveform 4)
I31-10 (SBLW) - Body ground*1, *2 Blower motor speed control signal
·

Ignition switch ON

·

Blower switch: LO


Pulse generation
(See waveform 2)
I31-20 (RLIN) - Body ground*2 LIN communication signal Ignition switch ON Pulse generation
(See waveform 1)
I30-8 (RRTR) - Body ground*1, *2 Room temperature sensor signal (for Rear RH)
·

Ignition switch ON

·

Vehicle interior temperature: 25°C (77°F)


1.9 to 2.1 V
·

Ignition switch ON

·

Vehicle interior temperature: 50°C (122°F)


1.0 to 1.2 V
I30-10 (RLTR) - Body ground*1, *2 Room temperature sensor signal (for Rear LH)
·

Ignition switch ON

·

Vehicle interior temperature: 25°C (77°F)


1.9 to 2.1 V
·

Ignition switch ON

·

Vehicle interior temperature: 50°C (122°F)


1.0 to 1.2 V
I30-11 (TEC) - Body ground*2 No. 2 cooler thermistor signal
·

Ignition switch ON

·

Evaporator temperature: 0°C (32°F)


1.7 to 2.1 V
·

Ignition switch ON

·

Evaporator temperature: 15°C (59°F)


0.9 to 1.3 V
I30-14 (SG-8) - Body ground*1, *2 Ground for sensor Always Below 1 Ω
I30-15 (SG-9) - Body ground*2 Ground for sensor Always Below 1 Ω
I30-17 (SWCB) - Body ground*6 Cool box drive permit signal
·

Ignition switch ON

·

Cool box switch: Off → on


Below 1 V → 4.5 to 5.5 V
I30-19 (COOL) - Body ground*6 Cool box drive request signal
·

Ignition switch ON

·

Cool box switch: Off → on


11 to 14 V → Below 1 V
z16-2 (BUSG) - Body ground Ground for BUS IC (for Front) Always Below 1 Ω
z16-3 (BUS) - Body BUS IC control signal (for Front) Ignition switch ON Pulse generation
(see waveform 4)
z16-4 (BBUS) - Body ground Power supply for BUS IC (for Front) Always 11 to 14 V
z16-5 (SG-3) - Body ground Ground for sensor Always Below 1 Ω
z16-6 (TE) - Body ground No. 1 cooler thermistor signal
·

Ignition switch ON

·

Evaporator temperature: 0°C (32°F)


1.7 to 2.1 V
·

Ignition switch ON

·

Evaporator temperature: 15°C (59°F)


0.9 to 1.3 V


e.
E334619N02
0.313,1.563 0.771,1.76 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Item Content

*: w/ Rear Air Conditioning System

Terminal No.
·

I33-7 (LIN1) - Body ground

·

I31-20 (RLIN) - Body ground*


Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON


f.
E338778N01
2.823,1.24 3.281,1.438 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

Item Content

*1: w/ Rear Cooler

*2: w/ Rear Air Conditioning System

Terminal No.
·

I33-21 (BLW) - Body ground

·

I31-10 (SBLW) - Body ground*1, *2


Tool Setting 2 V/DIV., 1 ms./DIV.
Condition
·

Ignition switch ON

·

Blower switch: LO



HINT:

The waveform varies with the blower speed.



g.
E147961E03
0.04,0.995 0.400,1.151 0.360,0.156 10 GND -0.021,-0.021 3.414,2.172 3.435,2.192

Using an oscilloscope, check waveform 3.

Item Content
Terminal No. I32-12 (LOCK) - Body ground
Tool Setting 200 mV/DIV., 10 ms./DIV.
Condition
·

Engine running

·

A/C switch: On (magnet clutch on)

·

Blower switch: LO



HINT:

When the engine speed is increased, the duty ratio changes accordingly.



h.
E202803N05
0.333,1.469 0.75,1.646 0.417,0.177 10 GND

Using an oscilloscope, check waveform 4.

Item Content

*: w/ Rear Air Conditioning System

Terminal No.
·

z16-3 (BUS) - Body ground

·

I31-7 (RBUS) - Body ground*


Tool Setting 2 V/DIV., 2 ms./DIV.
Condition Ignition switch ON



CHECK AIR CONDITIONING CONTROL ASSEMBLY


a.
E459590N01
1.396,0.25 1.896,0.5 0.5,0.25 1.552,0.281 2.01,0.479 0.458,0.198 10 false I78

Disconnect the I78 air conditioning control assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
I78-4 (E) - Body ground Ground Always Below 1 Ω
I78-7 (ACC) - Body ground Power source Ignition switch off Below 1 V
Ignition switch ACC 11 to 14 V
I78-8 (IG+) - Body ground Power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
I78-16 (+B) - Body ground Power source Always 11 to 14 V


c.

Reconnect the I78 air conditioning control assembly connector.


d.

Check for pulse according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
I78-3 (LIN1) - Body ground LIN communication signal Ignition switch ON Pulse generation
(see waveform 1)


e.
E334619N02
0.313,1.563 0.771,1.76 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Item Content
Terminal No. I78-3 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON



CHECK COOLER CONTROL SWITCH ASSEMBLY (w/ Rear Cooler)


a.
E459591N01
1.396,0.292 1.896,0.542 0.5,0.25 1.51,0.344 1.969,0.542 0.458,0.198 10 false Q34

Disconnect the Q34 cooler control switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
Q34-4 (SG) - Body ground Ground Always Below 1 Ω
Q34-2 (S5) - Body ground Power source
·

Ignition switch off

·

Blower switch: Off → HI


Below 1 V → 4.85 to 5.15 V


c.

Reconnect the Q34 cooler control switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
Q34-3 (BSET) - Body ground Volume switch of No. 2 air conditioning control assembly signal
·

Ignition switch off

·

Blower switch: Off → HI


Below 1 → 5.15 V



CHECK COOLER CONTROL SWITCH ASSEMBLY (w/ Rear Air Conditioning System)


a.
E459591N02
1.396,0.292 1.896,0.542 0.5,0.25 1.51,0.344 1.969,0.542 0.458,0.198 10 false Q52

Disconnect the Q52 cooler control switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
Q52-6 (E) - Body ground Ground Always Below 1 Ω
Q52-10 (IG+) - Body ground Power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


c.

Reconnect the Q52 cooler control switch assembly connector.


d.

Check for pulse according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
Q52-5 (RLIN) - Body ground LIN communication signal Ignition switch ON Pulse generation
(see waveform 1)


e.
E334619N02
0.313,1.563 0.771,1.76 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Item Content
Terminal No. Q52-5 (RLIN) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON