Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for 1GR-FE)
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467940 COMPRESSOR(for 1GR-FE) G

HEATING / AIR CONDITIONING  COMPRESSOR(for 1GR-FE)  INSPECTION  


PROCEDURE

Hide 88320 1.INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOOK SENSOR)

a.
E468031C01
1.51,0.406 1.917,0.594 0.406,0.188 1.115,1.844 1.365,1.281 true 2.021,1.833 1.771,1.292 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.917,1.875 1.531,2.073 0.615,0.198 10 false SSR+ 1.927,1.875 2.542,2.073 0.615,0.198 10 false SSR- 1.594,0.427 2.052,0.625 0.458,0.198 10 false C39
*a Component without harness connected
(Cooler Compressor Assembly (A/C Lock Sensor))


Inspect the cooler compressor assembly (A/C Lock Sensor)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C39)Location & Routing

Click Connector(C39)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Compressor with Magnet Clutch Assembly

C39-3 (SSR+) - C39-2 (SSR-) 20°C (68°F) 65 to 125 Ω


If the resistance is not as specified, replace the cooler compressor assembly.



Hide 88410 2.INSPECT MAGNET CLUTCH ASSEMBLY

a.

Inspect the magnet clutch assembly.

i.
E464864C02
0.406,0.042 0.823,0.219 0.417,0.177 0.635,1.073 0.771,0.583 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.49,1.094 0.948,1.292 0.458,0.198 10 false MG+ 0.479,0.052 0.938,0.281 0.458,0.229 10 false C39
*a Component without harness connected
(Compressor with magnet clutch)


Apply battery voltage to the clutch and check the operation of the clutch.

OK:
Tester Connection Specified Condition

Click Location & Routing(C39)Location & Routing

Click Connector(C39)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Compressor with Magnet Clutch Assembly

Battery positive (+) → C39-1 (MG+)
Battery negative (-) → Body ground
magnet clutch is engaged


If the value is not within the standard, perform the following inspections.


ii.
E460174C01
0.542,0.438 0.938,0.438 false 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.979,0.354 1.135,0.552 0.156,0.198 10 false 1
*a Component without harness connected
(Magnet Clutch Assembly)


Disconnect the wire harness of the compressor with magnet clutch and check that the magnet clutch assembly operates when battery voltage is applied to the connector terminal on the magnet clutch side.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Body ground
magnet clutch is engaged


·

If the result is not as specified, replace the magnet clutch assembly.

·

If the magnet clutch assembly is normal, replace the cooler compressor assembly.