Home › Vehicle Exterior › WINDOW / GLASS › FRONT PASSENGER SIDE POWER WINDOW SWITCH
RM38G0E _59 Vehicle Exterior _100806 WINDOW / GLASS _0467972 FRONT PASSENGER SIDE POWER WINDOW SWITCH G

WINDOW / GLASS  FRONT PASSENGER SIDE POWER WINDOW SWITCH  INSPECTION  


PROCEDURE

Hide 84810 1.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

a.

Inspect the power window regulator switch assembly.

i.
B563160C28
1.427,0.302 1.844,0.552 0.417,0.25 0.75,1.573 1.135,1.24 true 1.25,1.667 1.302,1.24 true 1.698,1.625 1.625,1.24 true 2.094,1.635 1.802,1.24 true 0.521,0.458 0.833,0.615 0.313,0.156 10 false *a 0.375,1.594 0.875,1.76 0.5,0.167 10 false AUTO 0.969,1.677 1.365,1.854 0.396,0.177 10 false GND 1.625,1.688 1.885,1.854 0.26,0.167 10 false UP 2.063,1.677 2.583,1.833 0.521,0.156 10 false DOWN 1.552,0.354 1.865,0.51 0.313,0.156 10 false M5
*a Component without harness connected
(Power Window Regulator Switch Assembly)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(M5)Location & Routing

Click Connector(M5)Body>Front Door Wire RH>Front Power Window Regulator Switch Assembly RH

M5-5 (UP) - M5-7 (GND) UP(MANUAL) → OFF Below 1 Ω → 10 kΩ or higher
M5-4 (DOWN) - M5-7 (GND) DOWN(MANUAL) → OFF Below 1 Ω → 10 kΩ or higher
M5-5 (UP) - M5-7 (GND)
M5-8 (AUTO) - M5-7 (GND)
UP(AUTO) → OFF Below 1 Ω → 10 kΩ or higher
M5-4 (DOWN) - M5-7 (GND)
M5-8 (AUTO) -M5-7 (GND)
DOWN(AUTO) → OFF Below 1 Ω → 10 kΩ or higher


If the result is not as specified, replace the power window regulator switch assembly.


ii.
B563160C31
1.427,0.302 1.844,0.552 0.417,0.25 0.75,1.573 1.135,1.24 true 1.25,1.667 1.302,1.24 true 1.698,1.625 1.625,1.24 true 2.094,1.635 1.802,1.24 true 0.521,0.458 0.833,0.615 0.313,0.156 10 false *a 0.375,1.594 0.875,1.76 0.5,0.167 10 false AUTO 0.969,1.677 1.365,1.854 0.396,0.177 10 false GND 1.625,1.688 1.885,1.854 0.26,0.167 10 false UP 2.063,1.677 2.583,1.833 0.521,0.156 10 false DOWN 1.552,0.354 1.865,0.51 0.313,0.156 10 false N4
*a Component without harness connected
(Power Window Regulator Switch Assembly)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(N4)Location & Routing

Click Connector(N4)Body>Front Door Wire LH>Front Power Window Regulator Switch Assembly LH

N4-5 (UP) - N4-7 (GND) UP(MANUAL) → OFF Below 1 Ω → 10 kΩ or higher
N4-4 (DOWN) - N4-7 (GND) DOWN(MANUAL) → OFF Below 1 Ω → 10 kΩ or higher
N4-5 (UP) - N4-7 (GND)
N4-8 (AUTO) - N4-7 (GND)
UP(AUTO) → OFF Below 1 Ω → 10 kΩ or higher
N4-4 (DOWN) - N4-7 (GND)
N4-8 (AUTO) - N4-7 (GND)
DOWN(AUTO) → OFF Below 1 Ω → 10 kΩ or higher


If the result is not as specified, replace the power window regulator switch assembly.



b.

Check the illumination.

i.
B563160C29
1.427,0.302 1.844,0.552 0.417,0.25 1.844,1.625 1.948,1.24 true 2.615,1.635 2.323,1.24 true 0.521,0.458 0.833,0.615 0.313,0.156 10 false *a 1.698,1.646 2.021,1.823 0.323,0.177 10 false ILL+ 2.635,1.656 3.156,1.813 0.521,0.156 10 false ILL- 1.531,0.354 1.844,0.51 0.313,0.156 10 false M5
*a Component without harness connected
(Power Window Regulator Switch Assembly)


for LHD:

Apply battery voltage to the connector and check the illumination conditions.

OK:
Tester Connection Specified Condition

Click Location & Routing(M5)Location & Routing

Click Connector(M5)Body>Front Door Wire RH>Front Power Window Regulator Switch Assembly RH

M5-3 (ILL+) - battery positive (+)
M5-1 (ILL-) - battery negative (-)
Illuminates


If the result is not as specified, replace the power window regulator switch assembly.


ii.
B563160C30
1.427,0.302 1.844,0.552 0.417,0.25 1.844,1.625 1.948,1.24 true 2.615,1.635 2.323,1.24 true 0.521,0.458 0.833,0.615 0.313,0.156 10 false *a 1.698,1.646 2.021,1.823 0.323,0.177 10 false ILL+ 2.635,1.656 3.156,1.813 0.521,0.156 10 false ILL- 1.531,0.354 1.844,0.51 0.313,0.156 10 false N4
*a Component without harness connected
(Power Window Regulator Switch Assembly)


for RHD:

Apply battery voltage to the connector and check the illumination conditions.

OK:
Tester Connection Specified Condition

Click Location & Routing(N4)Location & Routing

Click Connector(N4)Body>Front Door Wire LH>Front Power Window Regulator Switch Assembly LH

N4-3 (ILL+) - battery positive (+)
N4-1 (ILL-) - battery negative (-)
Illuminates


If the result is not as specified, replace the power window regulator switch assembly.