Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW SWITCH (for Rear Door)
RM38G0E _59 Vehicle Exterior _100806 WINDOW / GLASS _0467973 POWER WINDOW SWITCH(for Rear Door) G

WINDOW / GLASS  POWER WINDOW SWITCH(for Rear Door)  INSPECTION  


PROCEDURE

Hide 84810D 1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Side)

a.

Inspect the rear power window regulator switch assembly.

i.
C183233C30
1.354,0.406 1.802,0.615 0.448,0.208 0.76,2.24 1.135,1.969 true 1.135,2.292 1.333,1.979 true 1.5,2.313 1.625,1.979 true 1.802,2.333 1.802,1.979 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.448,2.292 0.948,2.531 0.5,0.24 10 false AUTO 1.396,2.354 1.896,2.594 0.5,0.24 10 false UP 0.979,2.323 1.479,2.563 0.5,0.24 10 false GND 1.698,2.375 2.198,2.615 0.5,0.24 10 false DOWN 1.51,0.438 1.823,0.635 0.313,0.198 10 false P3
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(P3)Location & Routing

Click Connector(P3)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Switch Assembly LH

P3-5 (UP) - P3-7 (GND) UP(MANUAL) → OFF Below 1 Ω → 10 kΩ or higher
P3-4 (DOWN) - P3-7 (GND) DOWN(MANUAL) → OFF Below 1 Ω → 10 kΩ or higher
P3-5 (UP) - P3-7 (GND)
P3-8 (AUTO) - P3-7 (GND)
UP(AUTO) → OFF Below 1 Ω → 10 kΩ or higher
P3-4 (DOWN) - P3-7 (GND)
P3-8 (AUTO) - P3-7 (GND)
DOWN(AUTO) → OFF Below 1 Ω → 10 kΩ or higher


If the result is not as specified, replace the rear power window regulator switch assembly.



b.
C183233C31
1.385,0.469 1.802,0.688 0.417,0.219 2.438,2.49 2.26,2.49 2.26,2.49 2.26,2 true 1.948,1.854 1.948,1.177 1.948,1.177 1.823,1.177 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 2.49,2.417 2.99,2.656 0.5,0.24 10 false ILL- 1.479,1.115 1.979,1.354 0.5,0.24 10 false ILL+ 1.542,0.49 1.854,0.688 0.313,0.198 10 false P3
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly)


Check the illumination.

i.

Apply battery voltage to the connector and check the illumination conditions.

OK:
Tester Connection Specified Condition

Click Location & Routing(P3)Location & Routing

Click Connector(P3)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Switch Assembly LH

P3-3 (ILL+) - battery positive (+)
P3-1 (ILL-) - battery negative (-)
Illuminates


If the result is not as specified, replace the rear power window regulator switch assembly.



Hide 84810D 2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Side)

a.
C183233C33
1.354,0.406 1.802,0.615 0.448,0.208 0.76,2.24 1.135,1.969 true 1.135,2.292 1.333,1.979 true 1.5,2.313 1.625,1.979 true 1.802,2.333 1.802,1.979 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.448,2.292 0.948,2.531 0.5,0.24 10 false AUTO 1.396,2.354 1.896,2.594 0.5,0.24 10 false UP 0.979,2.323 1.479,2.563 0.5,0.24 10 false GND 1.698,2.375 2.198,2.615 0.5,0.24 10 false DOWN 1.51,0.438 1.823,0.635 0.313,0.198 10 false O3
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly)


Inspect the rear power window regulator switch assembly.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O3)Location & Routing

Click Connector(O3)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Switch Assembly RH

O3-5 (UP) - O3-7 (GND) UP(MANUAL) → OFF Below 1 Ω → 10 kΩ or higher
O3-4 (DOWN) - O3-7 (GND) DOWN(MANUAL) → OFF Below 1 Ω → 10 kΩ or higher
O3-5 (UP) - O3-7 (GND)
O3-8 (AUTO) - O3-7 (GND)
UP(AUTO) → OFF Below 1 Ω → 10 kΩ or higher
O3-4 (DOWN) - O3-7 (GND)
O3-8 (AUTO) - O3-7 (GND)
DOWN(AUTO) → OFF Below 1 Ω → 10 kΩ or higher


If the result is not as specified, replace the rear power window regulator switch assembly.



b.
C183233C32
1.385,0.469 1.854,0.667 0.469,0.198 2.438,2.49 2.26,2.49 2.26,2.49 2.26,2 true 1.948,1.854 1.948,1.177 1.948,1.177 1.823,1.177 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 2.49,2.417 2.99,2.656 0.5,0.24 10 false ILL- 1.479,1.115 1.979,1.354 0.5,0.24 10 false ILL+ 1.542,0.49 1.854,0.688 0.313,0.198 10 false O3
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly)


Check the illumination.

i.

Apply battery voltage to the connector and check the illumination conditions.

OK:
Tester Connection Specified Condition

Click Location & Routing(O3)Location & Routing

Click Connector(O3)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Switch Assembly RH

O3-3 (ILL+) - battery positive (+)
O3-1 (ILL-) - battery negative (-)
Illuminates


If the result is not as specified, replace the rear power window regulator switch assembly.