Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)
RM38G0E _59 Vehicle Exterior _100806 WINDOW / GLASS _0467974 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720C 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for LHD)

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal N5-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.



a.

Check that the motor gear rotates smoothly as follows.

E459276C01
2.313,0.604 2.656,0.792 0.344,0.188 2.563,1.281 3.146,1.281 true 1.844,1.281 2.26,1.281 true 2.604,1.615 2.865,1.979 true 1.917,1.99 2.24,1.625 true 1.563,0.438 1.875,0.594 0.313,0.156 10 false *a 6.146,2.208 6.458,2.365 0.313,0.156 10 false *b 3.177,1.188 3.635,1.385 0.458,0.198 10 false GND 1.698,1.188 2.156,1.385 0.458,0.198 10 false B 2.792,2.01 3.25,2.208 0.458,0.198 10 false DOWN 1.771,2.021 2.229,2.219 0.458,0.198 10 false UP 2.396,0.615 2.854,0.813 0.458,0.198 10 false N5
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(N5)Location & Routing

Click Connector(N5)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

1.

Connect the positive (+) lead of the battery to terminal N5-2 (B) and the negative (-) lead to terminal N5-1 (GND), and hold for 3 seconds or more.

2.

While terminals N5-2 (B) and N5-1 (GND) are connected, connect the negative (-) lead of the battery to terminal N5-10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal N5-10 (UP), connect terminal N5-10 (UP) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates counterclockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal N5-2 (B) and the negative (-) lead to terminal N5-1 (GND), and hold for 3 seconds or more.

2.

While terminals N5-2 (B) and N5-1 (GND) are connected, connect the negative (-) lead of the battery to terminal N5-7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal N5-7 (DOWN), connect terminal N5-7 (DOWN) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates clockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for LHD)

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal M7-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.



a.

Check that the motor gear rotates smoothly as follows.

E459277C01
5.021,0.625 5.375,0.813 0.354,0.188 4.563,1.271 4.979,1.271 true 5.271,1.281 5.854,1.281 true 5.313,1.615 5.667,2 true 4.656,2 4.958,1.625 true 4.26,0.375 4.51,0.552 0.25,0.177 10 false *a 1.385,2.219 1.698,2.375 0.313,0.156 10 false *b 4.417,1.177 4.573,1.375 0.156,0.198 10 false B 5.896,1.177 6.313,1.427 0.417,0.25 10 false GND 5.563,2.021 6.063,2.271 0.5,0.25 10 false DOWN 4.542,2.031 4.875,2.281 0.333,0.25 10 false UP 5.104,0.635 5.354,0.813 0.25,0.177 10 false M7
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(M7)Location & Routing

Click Connector(M7)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

1.

Connect the positive (+) lead of the battery to terminal M7-2 (B) and the negative (-) lead to terminal M7-1 (GND), and hold for 3 seconds or more.

2.

While terminals M7-2 (B) and M7-1 (GND) are connected, connect the negative (-) lead of the battery to terminal M7-10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal M7-10 (UP), connect terminal M7-10 (UP) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal M7-2 (B) and the negative (-) lead to terminal M7-1 (GND), and hold for 3 seconds or more.

2.

While terminals M7-2 (B) and M7-1 (GND) are connected, connect the negative (-) lead of the battery to terminal M7-7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal M7-7 (DOWN), connect terminal M7-7 (DOWN) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates counterclockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly RH.


Hide 85720C 3.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for RHD)

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal N6-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.



a.

Check that the motor gear rotates smoothly as follows.

E459276C02
2.313,0.604 2.656,0.792 0.344,0.188 2.563,1.281 3.146,1.281 true 1.844,1.281 2.26,1.281 true 2.604,1.615 2.865,1.979 true 1.917,1.99 2.24,1.625 true 1.563,0.438 1.875,0.594 0.313,0.156 10 false *a 6.146,2.208 6.458,2.365 0.313,0.156 10 false *b 3.177,1.188 3.635,1.385 0.458,0.198 10 false GND 1.698,1.188 2.156,1.385 0.458,0.198 10 false B 2.792,2.01 3.25,2.208 0.458,0.198 10 false DOWN 1.771,2.021 2.229,2.219 0.458,0.198 10 false UP 2.396,0.615 2.854,0.813 0.458,0.198 10 false N6
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(N6)Location & Routing

Click Connector(N6)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

1.

Connect the positive (+) lead of the battery to terminal N6-2 (B) and the negative (-) lead to terminal N6-1 (GND), and hold for 3 seconds or more.

2.

While terminals N6-2 (B) and N6-1 (GND) are connected, connect the negative (-) lead of the battery to terminal N6-10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal N6-10 (UP), connect terminal N6-10 (UP) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates counterclockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal N6-2 (B) and the negative (-) lead to terminal N6-1 (GND), and hold for 3 seconds or more.

2.

While terminals N6-2 (B) and N6-1 (GND) are connected, connect the negative (-) lead of the battery to terminal N6-7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal N6-7 (DOWN), connect terminal N6-7 (DOWN) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates clockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710D 4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for RHD)

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal M6-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.



a.

Check that the motor gear rotates smoothly as follows.

E459277C02
5.021,0.625 5.375,0.813 0.354,0.188 4.563,1.271 4.979,1.271 true 5.271,1.281 5.854,1.281 true 5.313,1.615 5.667,2 true 4.656,2 4.958,1.625 true 4.26,0.375 4.51,0.552 0.25,0.177 10 false *a 1.385,2.219 1.698,2.375 0.313,0.156 10 false *b 4.417,1.177 4.573,1.375 0.156,0.198 10 false B 5.896,1.177 6.313,1.427 0.417,0.25 10 false GND 5.563,2.021 6.063,2.271 0.5,0.25 10 false DOWN 4.542,2.031 4.875,2.281 0.333,0.25 10 false UP 5.104,0.635 5.354,0.813 0.25,0.177 10 false M6
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(M6)Location & Routing

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

1.

Connect the positive (+) lead of the battery to terminal M6-2 (B) and the negative (-) lead to terminal M6-1 (GND), and hold for 3 seconds or more.

2.

While terminals M6-2 (B) and M6-1 (GND) are connected, connect the negative (-) lead of the battery to terminal M6-10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal M6-10 (UP), connect terminal M6-10 (UP) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal M6-2 (B) and the negative (-) lead to terminal M6-1 (GND), and hold for 3 seconds or more.

2.

While terminals M6-2 (B) and M6-1 (GND) are connected, connect the negative (-) lead of the battery to terminal M6-7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal M6-7 (DOWN), connect terminal M6-7 (DOWN) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates counterclockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly RH.