Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door)
RM38G0E _59 Vehicle Exterior _100806 WINDOW / GLASS _0467975 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


PROCEDURE

Hide 85720G 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal P4-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.



a.

Check that the motor gear rotates smoothly as follows.

E459284C01
1.625,0.604 1.99,0.792 0.365,0.188 1.177,1.271 1.594,1.271 true 1.896,1.271 2.479,1.271 true 1.948,1.615 2.25,1.99 true 1.333,2 1.563,1.625 true 0.865,0.396 1.177,0.552 0.313,0.156 10 false *a 6.313,2.115 6.625,2.271 0.313,0.156 10 false *b 2.135,2.031 2.75,2.229 0.615,0.198 10 false DOWN 1.188,2.031 1.802,2.229 0.615,0.198 10 false UP 2.521,1.156 3.135,1.354 0.615,0.198 10 false GND 1.021,1.177 1.24,1.375 0.219,0.198 10 false B 1.708,0.615 2.323,0.813 0.615,0.198 10 false P4
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(P4)Location & Routing

Click Connector(P4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

1.

Connect the positive (+) lead of the battery to terminal P4-2 (B) and the negative (-) lead to terminal P4-1 (GND), and hold for 3 seconds or more.

2.

While terminals P4-2 (B) and P4-1 (GND) are connected, connect the negative (-) lead of the battery to terminal P4-10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal P4-10 (UP), connect terminal P4-10 (UP) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates counterclockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal P4-2 (B) and the negative (-) lead to terminal P4-1 (GND), and hold for 3 seconds or more.

2.

2. While terminals P4-2 (B) and P4-1 (GND) are connected, connect the negative (-) lead of the battery to terminal P4-7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal P4-7 (DOWN), connect terminal P4-7 (DOWN) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates clockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710F 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal O4-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.



a.

Check that the motor gear rotates smoothly as follows.

E459285C01
5.208,0.583 5.521,0.76 0.313,0.177 5.438,1.271 6.021,1.271 true 4.708,1.271 5.125,1.271 true 4.813,1.917 5.115,1.594 true 5.5,1.583 5.792,1.917 true 4.448,0.385 4.76,0.542 0.313,0.156 10 false *a 0.75,2.042 1.063,2.198 0.313,0.156 10 false *b 6.073,1.188 6.385,1.344 0.313,0.156 10 false GND 4.552,1.167 4.865,1.323 0.313,0.156 10 false B 5.656,1.948 6.208,2.146 0.552,0.198 10 false DOWN 4.698,1.969 5.135,2.167 0.438,0.198 10 false UP 5.271,0.594 5.583,0.792 0.313,0.198 10 false O4
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

1.

Connect the positive (+) lead of the battery to terminal O4-2 (B) and the negative (-) lead to terminal O4-1 (GND), and hold for 3 seconds or more.

2.

While terminals O4-2 (B) and O4-1 (GND) are connected, connect the negative (-) lead of the battery to terminal O4-10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal O4-10 (UP), connect terminal O4-10 (UP) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal O4-2 (B) and the negative (-) lead to terminal O4-1 (GND), and hold for 3 seconds or more.

2.

While terminals O4-2 (B) and O4-1 (GND) are connected, connect the negative (-) lead of the battery to terminal O4-7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal O4-7 (DOWN), connect terminal O4-7 (DOWN) to the negative (-) lead of the battery again within 1 second.


Motor gear rotates counterclockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly RH.