84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD, w/o Reverse Shift-linked Mirror)
Check the mirror select switch and mirror surface adjust switch.
| *a | Mirror Select and Surface Adjust Switch |
| *b | Mirror Retract Switch |
| *c | Component without harness connected (Outer Mirror Switch Assembly) |
Turn the mirror select switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(N14)Location & Routingewd_type=routing;type=c;code=N14 Click Connector(N14)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N14;pinno=2,6,11,7,4 |
||
| N14-2 (VL) - N14-6 (B) N14-11 (M+) - N14-7 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| N14-2 (VL) - N14-7 (E) N14-11 (M+) - N14-6 (B) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| N14-4 (HL) - N14-6 (B) N14-11 (M+) - N14-7 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| N14-4 (HL) - N14-7 (E) N14-11 (M+) - N14-6 (B) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher | |
Turn the mirror select switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(N14)Location & Routingewd_type=routing;type=c;code=N14 Click Connector(N14)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N14;pinno=5,6,11,7,3 |
||
| N14-5 (VR) - N14-6 (B) N14-11 (M+) - N14-7 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| N14-5 (VR) - N14-7 (E) N14-11 (M+) - N14-6 (B) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| N14-3 (HR) - N14-6 (B) N14-11 (M+) - N14-7 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| N14-3 (HR) - N14-7 (E) N14-11 (M+) - N14-6 (B) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher | |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(N14)Location & Routingewd_type=routing;type=c;code=N14 Click Connector(N14)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N14;pinno=9,6,10,7 |
||
| N14-9 (MF) - N14-6 (B) N14-10 (MR) - N14-7 (E) |
Driving position | Below 1 Ω |
| N14-10 (MR) - N14-6 (B) N14-9 (MF) - N14-7 (E) |
Retract position | Below 1 Ω |
Check that the LED illuminates.
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
Click Location & Routing(N14)Location & Routingewd_type=routing;type=c;code=N14 Click Connector(N14)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N14;pinno=12,1 |
|
| Auxiliary battery positive (+) - N14-12 (ILL+) Auxiliary battery negative (-) - N14-1 (ILL-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.
84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD, w/ Reverse Shift-linked Mirror)
| *a | Mirror Select and Surface Adjust Switch |
| *b | Mirror Retract Switch |
| *c | Component without harness connected (Outer Mirror Switch Assembly) |
Check the mirror select switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(N14)Location & Routingewd_type=routing;type=c;code=N14 Click Connector(N14)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N14;pinno=5,7 |
||
| N14-5 (MSW) - N14-7 (E) | Mirror select switch turned to R position | Below 10 Ω |
| Mirror select switch off | 10 kΩ or higher | |
| Mirror select switch turned to L position | 90 to 110 Ω | |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror surface adjust switch.
Turn the mirror select switch to the L or R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(N14)Location & Routingewd_type=routing;type=c;code=N14 Click Connector(N14)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N14;pinno=4,7 |
||
| N14-4 (M+) - N14-7 (E) | Mirror surface adjust switch pushed up | 90 to 110 Ω |
| Mirror surface adjust switch pushed down | 437 to 503 Ω | |
| Mirror surface adjust switch pushed left | 744 to 856 Ω | |
| Mirror surface adjust switch pushed right | 225 to 275 Ω | |
| Mirror surface adjust switch not pushed | 10 kΩ or higher | |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(N14)Location & Routingewd_type=routing;type=c;code=N14 Click Connector(N14)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N14;pinno=9,8,10 |
||
| N14-9 (MAT) - N14-8 (E) | AUTO position | Below 35 Ω |
| N14-9 (MAT) - N14-8 (E) | Except AUTO position | 10 kΩ or higher |
| N14-10 (MR) - N14-8 (E) | Retract position | Below 35 Ω |
| N14-10 (MR) - N14-8 (E) | Except retract position | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates.
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
Click Location & Routing(N14)Location & Routingewd_type=routing;type=c;code=N14 Click Connector(N14)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N14;pinno=12,1 |
|
| Auxiliary battery positive (+) - N14-12 (ILL+) Auxiliary battery negative (-) - N14-1 (ILL-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.
84870A 3.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD, w/o Reverse Shift-linked Mirror)
Check the mirror select switch and mirror surface adjust switch.
| *a | Mirror Select and Surface Adjust Switch |
| *b | Mirror Retract Switch |
| *c | Component without harness connected (Outer Mirror Switch Assembly) |
Turn the mirror select switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(M16)Location & Routingewd_type=routing;type=c;code=M16 Click Connector(M16)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M16;pinno=2,6,11,7,4 |
||
| M16-2 (VL) - M16-6 (B) M16-11 (M+) - M16-7 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| M16-2 (VL) - M16-7 (E) M16-11 (M+) - M16-6 (B) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| M16-4 (HL) - M16-6 (B) M16-11 (M+) - M16-7 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| M16-4 (HL) - M16-7 (E) M16-11 (M+) - M16-6 (B) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher | |
Turn the mirror select switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(M16)Location & Routingewd_type=routing;type=c;code=M16 Click Connector(M16)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M16;pinno=5,6,11,7,3 |
||
| M16-5 (VR) - M16-6 (B) M16-11 (M+) - M16-7 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| M16-5 (VR) - M16-7 (E) M16-11 (M+) - M16-6 (B) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| M16-3 (HR) - M16-6 (B) M16-11 (M+) - M16-7 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| M16-3 (HR) - M16-7 (E) M16-11 (M+) - M16-6 (B) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher | |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(M16)Location & Routingewd_type=routing;type=c;code=M16 Click Connector(M16)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M16;pinno=9,6,10,7 |
||
| M16-9 (MF) - M16-6 (B) M16-10 (MR) - M16-7 (E) |
Driving position | Below 1 Ω |
| M16-10 (MR) - M16-6 (B) M16-9 (MF) - M16-7 (E) |
Retract position | Below 1 Ω |
Check that the LED illuminates.
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
Click Location & Routing(M16)Location & Routingewd_type=routing;type=c;code=M16 Click Connector(M16)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M16;pinno=12,1 |
|
| Auxiliary battery positive (+) - M16-12 (ILL+) Auxiliary battery negative (-) - M16-1 (ILL-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.
84870A 4.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD, w/ Reverse Shift-linked Mirror)
| *a | Mirror Select and Surface Adjust Switch |
| *b | Mirror Retract Switch |
| *c | Component without harness connected (Outer Mirror Switch Assembly) |
Check the mirror select switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(M16)Location & Routingewd_type=routing;type=c;code=M16 Click Connector(M16)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M16;pinno=5,7 |
||
| M16-5 (MSW) - M16-7 (E) | Mirror select switch turned to R position | Below 10 Ω |
| Mirror select switch off | 10 kΩ or higher | |
| Mirror select switch turned to L position | 90 to 110 Ω | |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror surface adjust switch.
Turn the mirror select switch to the L or R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(M16)Location & Routingewd_type=routing;type=c;code=M16 Click Connector(M16)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M16;pinno=4,7 |
||
| M16-4 (M+) - M16-7 (E) | Mirror surface adjust switch pushed up | 90 to 110 Ω |
| Mirror surface adjust switch pushed down | 437 to 503 Ω | |
| Mirror surface adjust switch pushed left | 744 to 856 Ω | |
| Mirror surface adjust switch pushed right | 225 to 275 Ω | |
| Mirror surface adjust switch not pushed | 10 kΩ or higher | |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(M16)Location & Routingewd_type=routing;type=c;code=M16 Click Connector(M16)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M16;pinno=9,8,10 |
||
| M16-9 (MAT) - M16-8 (E) | AUTO position | Below 35 Ω |
| M16-9 (MAT) - M16-8 (E) | Except AUTO position | 10 kΩ or higher |
| M16-10 (MR) - M16-8 (E) | Retract position | Below 35 Ω |
| M16-10 (MR) - M16-8 (E) | Except retract position | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates.
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
Click Location & Routing(M16)Location & Routingewd_type=routing;type=c;code=M16 Click Connector(M16)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M16;pinno=12,1 |
|
| Auxiliary battery positive (+) - M16-12 (ILL+) Auxiliary battery negative (-) - M16-1 (ILL-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.