DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory Switch1 | Seat memory switch M1 switch signal | OFF or ON | OFF: Seat memory switch M1 switch off ON: Seat memory switch M1 switch on |
w/ Memory |
| Seat Memory Switch2 | Seat memory switch M2 switch signal | OFF or ON | OFF: Seat memory switch M2 switch off ON: seat memory switch LH M2 switch on |
w/ Memory |
| Seat Memory Switch3 | Seat memory switch M3 switch signal | OFF or ON | OFF: Seat memory switch M3 switch off ON: Seat memory switch M3 switch on |
w/ Memory |
| Seat Memory Set SW | Seat memory switch SET switch signal | OFF or ON | OFF: Seat memory switch SET switch off ON: Seat memory switch SET switch on |
w/ Memory |
| Mirror Vertical Sensor Vol | Vertical mirror position | MIN: 0, MAX: 5 V | 0 to 5 V | - |
| Mirror Horizontal Sensor Vol | Horizontal mirror position | MIN: 0, MAX: 5 V | 0 to 5 V | - |
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 25.5 V | 11 to 14 V | - |
| # Codes | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
| Mirror Memory Driver1 No.1 | Mirror position memorized in memory switch M1 | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Mirror Memory Driver1 No.2 | Mirror position memorized in memory switch M2 | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Mirror Memory Driver1 No.3 | Mirror position memorized in memory switch M3 | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Mirror Memory Driver1 Last Position | Mirror position memorized in memory last position | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Mirror Memory (Reverse) Driver1 | Mirror reverse shift linked position No. 1 memorized | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory Switch1 | Seat memory switch M1 switch signal | OFF or ON | OFF: Seat memory switch M1 switch off ON: Seat memory switch M1 switch on |
w/ Memory |
| Seat Memory Switch2 | Seat memory switch M2 switch signal | OFF or ON | OFF: Seat memory switch M2 switch off ON: Seat memory switch M2 switch on |
w/ Memory |
| Seat Memory Switch3 | Seat memory switch M3 switch signal | OFF or ON | OFF: Seat memory switch M3 switch off ON: Seat memory switch M3 switch on |
w/ Memory |
| Seat Memory Set SW | seat memory switch RH SET switch signal | OFF or ON | OFF: seat memory switch RH SET switch off ON: seat memory switch RH SET switch on |
w/ Memory |
| Mirror Vertical Sensor Vol | Vertical mirror position | MIN: 0, MAX: 5 V | 0 to 5 V | - |
| Mirror Horizontal Sensor Vol | Horizontal mirror position | MIN: 0, MAX: 5 V | 0 to 5 V | - |
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 25.5 V | 11 to 14 V | - |
| # Codes | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
| Mirror Memory Driver1 No.1 | Mirror position memorized in memory switch M1 | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Mirror Memory Driver1 No.2 | Mirror position memorized in memory switch M2 | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Mirror Memory Driver1 No.3 | Mirror position memorized in memory switch M3 | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Mirror Memory Driver1 Last Position | Mirror position memorized in memory last position | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Mirror Memory (Reverse) Driver1 | Mirror reverse shift linked position No. 1 memorized | OFF or ON | OFF: Not memorized ON: Memorized |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Outer Mirror Fold Switch | Retractable outer mirror switch signal | OFF or ON | OFF: Retractable outer mirror switch not in retract position ON: Retractable outer mirror switch in retract position |
- |
| Outer Mirror Auto Switch | Retractable outer mirror switch signal | OFF or ON | OFF: Retractable outer mirror switch not in auto position ON: Retractable outer mirror switch in auto position |
- |
| Outer Mirror Control Switch (RH Select) | Mirror select switch signal for RH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch R switch on |
- |
| Outer Mirror Control Switch (LH Select) | Mirror select switch signal for LH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch L switch on |
- |
| Outer Mirror Control Switch (Surface Adjust Right) | Mirror adjust switch signal (Right) | OFF or ON | OFF: Mirror adjust switch not pushed right ON: Mirror adjust switch pushed right |
Check with the mirror select switch L or R selected |
| Outer Mirror Control Switch (Surface Adjust Left) | Mirror adjust switch signal (Left) | OFF or ON | OFF: Mirror adjust switch not pushed left ON: Mirror adjust switch pushed left |
Check with the mirror select switch L or R selected |
| Outer Mirror Control Switch (Surface Adjust Up) | Mirror adjust switch signal (Up) | OFF or ON | OFF: Mirror adjust switch not pushed up ON: Mirror adjust switch pushed up |
Check with the mirror select switch L or R selected |
| Outer Mirror Control Switch (Surface Adjust Down) | Mirror adjust switch signal (Down) | OFF or ON | OFF: Mirror adjust switch not pushed down ON: Mirror adjust switch pushed down |
Check with the mirror select switch L or R selected |
| MEM Switch No. with Key ID 1 | Switch linked with key ID1 | NONE, MEM SW1, MEM SW2, or MEM SW3 | NONE: No switches linked with key ID1 MEM SW1: M1 linked with key ID1 MEM SW2: M2 linked with key ID1 MEM SW3: M3 linked with key ID1 |
- |
| MEM Switch No. with Key ID 2 | Switch linked with key ID2 | NONE, MEM SW1, MEM SW2, or MEM SW3 | NONE: No switches linked with key ID2 MEM SW1: M1 linked with key ID2 MEM SW2: M2 linked with key ID2 MEM SW3: M3 linked with key ID2 |
- |
| MEM Switch No. with Key ID 3 | Switch linked with key ID3 | NONE, MEM SW1, MEM SW2, or MEM SW3 | NONE: No switches linked with key ID3 MEM SW1: M1 linked with key ID3 MEM SW2: M2 linked with key ID3 MEM SW3: M3 linked with key ID3 |
- |
| MEM Switch No. with Key ID 4 | Switch linked with key ID4 | NONE, MEM SW1, MEM SW2, or MEM SW3 | NONE: No switches linked with key ID4 MEM SW1: M1 linked with key ID4 MEM SW2: M2 linked with key ID4 MEM SW3: M3 linked with key ID4 |
- |
| MEM Switch No. with Key ID 5 | Switch linked with key ID5 | NONE, MEM SW1, MEM SW2, or MEM SW3 | NONE: No switches linked with key ID5 MEM SW1: M1 linked with key ID5 MEM SW2: M2 linked with key ID5 MEM SW3: M3 linked with key ID5 |
- |
| MEM Switch No. with Key ID 6 | Switch linked with key ID6 | NONE, MEM SW1, MEM SW2, or MEM SW3 | NONE: No switches linked with key ID6 MEM SW1: M1 linked with key ID6 MEM SW2: M2 linked with key ID6 MEM SW3: M3 linked with key ID6 |
- |
| MEM Switch No. with Key ID 7 | Switch linked with key ID7 | NONE, MEM SW1, MEM SW2, or MEM SW3 | NONE: No switches linked with key ID7 MEM SW1: M1 linked with key ID7 MEM SW2: M2 linked with key ID7 MEM SW3: M3 linked with key ID7 |
- |
| Driver Seat MEM_1 Memory | Seat position memorized with M1 switch | ON or OFF | ON: Memorized OFF: Not Memorized |
- |
| Driver Seat MEM_2 Memory | Seat position memorized with M2 switch | ON or OFF | ON: Memorized OFF: Not Memorized |
- |
| Driver Seat MEM_3 Memory | Seat position memorized with M3 switch | ON or OFF | ON: Memorized OFF: Not Memorized |
- |
| Automatic Mirror Fold Setting | Function that changes the condition under which the outer mirrors automatically retract | ACC, Door Lock or Disable | Customize setting displayed | - |
| Reverse Coupled Actuation Mirror Angle Setting | Function that turns the reverse shift-linked mirror position memorization function state | Default Setting or User Setting | Customize setting displayed | - |
ACTIVE TEST
Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Foot Light | Foot light illumination operation | OFF or ON | - |
| Mirror Up/Down | Mirror vertical operation | OFF, Down or Up |
·
Operate with the ignition switch ON and the vehicle stopped.
·
This test tilts the mirror up or down.
·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Mirror Right/Left | Mirror horizontal operation | OFF, Right or Left |
·
Operate with the ignition switch ON and the vehicle stopped.
·
This test tilts the mirror right or left.
·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Mirror Fold/Return | Mirror retract operation | OFF, Return or Fold |
·
Operate with the ignition switch ON and the vehicle stopped.
·
This test activates the Fold/Return.
·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Mirror Heater | Mirror heater operation | OFF or ON |
·
Operate with the ignition switch ON and the vehicle stopped.
·
This test turns the mirror heater on or off.
·
Mirror heater operation can be confirmed by touch. |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Foot Light | Foot light illumination operation | OFF or ON | - |
| Mirror Up/Down | Mirror vertical operation | OFF, Down or Up |
·
Operate with the ignition switch ON and the vehicle stopped.
·
This test tilts the mirror up or down.
·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Mirror Right/Left | Mirror horizontal operation | OFF, Right or Left |
·
Operate with the ignition switch ON and the vehicle stopped.
·
This test tilts the mirror right or left.
·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Mirror Fold/Return | Mirror retract operation | OFF, Return or Fold |
·
Operate with the ignition switch ON and the vehicle stopped.
·
This test activates the Fold/Return.
·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Mirror Heater | Mirror heater operation | OFF or ON |
·
Operate with the ignition switch ON and the vehicle stopped.
·
This test turns the mirror heater on or off.
·
Mirror heater operation can be confirmed by touch. |