Home › Vehicle Exterior › LIGHTING (EXT) › REAR COMBINATION LIGHT ASSEMBLY
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468050 REAR COMBINATION LIGHT ASSEMBLY G

LIGHTING (EXT)  REAR COMBINATION LIGHT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 1.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

a.

Check the illumination.

i.
E466131C01
1.583,0.167 1.927,0.406 0.344,0.24 0.844,0.688 1.354,1.063 true 1.875,1.344 2.271,1.823 true 2.094,1.094 2.604,0.885 true 0.844,1.74 1.563,1.313 true 1.667,0.198 1.979,0.396 0.313,0.198 10 false c2 0.708,0.583 0.865,0.781 0.156,0.198 10 false E 0.646,1.688 1,1.885 0.354,0.198 10 false TL 2.667,0.802 3.135,1.073 0.469,0.271 10 false TRN 2.292,1.833 2.76,2.104 0.469,0.271 10 false STP 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Rear Combination Light Assembly LH)


Apply battery voltage to the rear combination light assembly LH and check that the light illuminates.

OK:
Tester Connection Specified Condition

*: for Bulb Type Turn Signal Light

Click Location & Routing(c2)Location & Routing

Click Connector(c2)Body>No. 8 Floor Wire>Rear Combination Light Assembly LH

Battery positive (+) - c2-7(TL)
Battery negative (-) - c2-4(E)
Taillight illuminates
Battery positive (+) - c2-6(STP)
Battery negative (-) - c2-4(E)
Stop light illuminates
Battery positive (+) - c2-1(TRN)
Battery negative (-) - c2-4(E)
Turn light illuminates*


If the result is not as specified, replace the rear combination light assembly LH.



Hide 2.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

a.

Check the illumination.

i.
E466131C02
1.552,0.167 1.875,0.375 0.323,0.208 0.896,0.688 1.406,1.021 true 2.073,1.073 2.635,0.75 true 1.052,1.74 1.573,1.333 true 1.865,1.344 2.302,1.76 true 1.625,0.198 1.938,0.396 0.313,0.198 10 false b2 0.76,0.604 0.917,0.802 0.156,0.198 10 false E 0.844,1.719 1.177,1.927 0.333,0.208 10 false TL 2.719,0.677 3.125,0.865 0.406,0.188 10 false TRN 2.333,1.781 2.74,1.969 0.406,0.188 10 false STP 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Rear Combination Light Assembly RH)


Apply battery voltage to the rear combination light assembly RH and check that the light illuminates.

OK:
Tester Connection Specified Condition

*: for Bulb Type Turn Signal Light

Click Location & Routing(b2)Location & Routing

Click Connector(b2)Body>No. 7 Floor Wire>Rear Combination Light Assembly RH

Battery positive (+) - b2-7(TL)
Battery negative (-) - b2-4(E)
Taillight illuminates
Battery positive (+) - b2-6(STP)
Battery negative (-) - b2-4(E)
Stop light illuminates
Battery positive (+) - b2-1(TRN)
Battery negative (-) - b2-4(E)
Turn light illuminates*


If the result is not as specified, replace the rear combination light assembly RH.



Hide 81565D 3.INSPECT REAR COMBINATION LIGHT CORD LH

a.

Inspect the rear combination light cord LH.

i.

Measure the resistance according to the value(s) in the table below.

E465421C01
1.875,0.135 2.156,0.333 0.281,0.198 4.906,0.073 5.188,0.271 0.281,0.198 2.292,0.875 2.667,0.542 true 2.125,1.073 2.49,1.438 true 1.75,0.854 1.313,0.583 true 1.906,1.083 1.521,1.448 true 1.927,0.167 2.24,0.365 0.313,0.198 10 false c2 4.979,0.115 5.292,0.313 0.313,0.198 10 false A 2.708,0.438 3.167,0.635 0.458,0.198 10 false TRN 2.417,1.448 2.875,1.646 0.458,0.198 10 false STP 1.198,0.469 1.656,0.667 0.458,0.198 10 false E 1.396,1.469 1.854,1.667 0.458,0.198 10 false TL 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Rear Combination Light Cord LH)
- -


Standard Resistance
Tester Connection Condition Specified Condition

*: for Bulb Type Turn Signal Light

Click Location & Routing(c2)Location & Routing

Click Connector(c2)Body>No. 8 Floor Wire>Rear Combination Light Assembly LH

c2-1(TRN) - A1* Always Below 1 Ω
c2-4(E) - A5
c2-6(STP) - A8
c2-7(TL) - A7

If the result is not as specified, replace the rear combination light cord LH.



Hide 81555G 4.INSPECT REAR COMBINATION LIGHT CORD RH

a.

Inspect the rear combination light cord RH.

i.

Measure the resistance according to the value(s) in the table below.

E465421C04
1.875,0.135 2.156,0.333 0.281,0.198 4.906,0.073 5.188,0.271 0.281,0.198 2.292,0.875 2.667,0.542 true 2.156,1.083 2.479,1.479 true 1.75,0.854 1.365,0.552 true 1.927,1.073 1.635,1.479 true 1.917,0.167 2.229,0.365 0.313,0.198 10 false b2 4.979,0.115 5.292,0.313 0.313,0.198 10 false A 2.708,0.406 3.167,0.604 0.458,0.198 10 false TRN 2.438,1.521 2.896,1.719 0.458,0.198 10 false STP 1.24,0.427 1.698,0.625 0.458,0.198 10 false E 1.531,1.51 1.99,1.708 0.458,0.198 10 false TL 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a
*a Component without harness connected
(Rear Combination Light Cord RH)
- -


Standard Resistance
Tester Connection Condition Specified Condition

*: for Bulb Type Turn Signal Light

Click Location & Routing(b2)Location & Routing

Click Connector(b2)Body>No. 7 Floor Wire>Rear Combination Light Assembly RH

b2-1(TRN) - A1* Always Below 1 Ω
b2-4(E) - A5
b2-6(STP) - A8
b2-7(TL) - A7

If the result is not as specified, replace the rear combination light cord RH.