81590A 1.INSPECT REAR LIGHT ASSEMBLY LH
| *a | Component without harness connected (Rear Light Assembly LH) |
Apply battery voltage to the rear light assembly LH and check that the light illuminates.
| Tester Connection | Specified Condition |
|---|---|
|
*1: w/ Rear Fog Light *2: w/ Sequential Rear Turn Signal Light |
|
Click Location & Routing(g2)Location & Routingewd_type=routing;type=c;code=g2 Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LHewd_type=component;type=c;code=g2;pinno=6,4,7,9,10 |
|
| Battery positive (+) - g2-6(B) | Taillight illuminates |
| Battery negative (-) - g2-4(E) | |
| Battery positive (+) - g2-7(B) | Rear fog light illuminates*1 |
| Battery negative (-) - g2-4(E) | |
| Battery positive (+) - g2-9(B) | Back up light illuminates |
| Battery negative (-) - g2-4(E) | |
| Battery positive (+) - g2-10(B) | Stop light illuminates*2 |
| Battery negative (-) - g2-4(E) | |
If the result is not as specified, replace the rear light assembly LH.
81580A 2.INSPECT REAR LIGHT ASSEMBLY RH
| *a | Component without harness connected (Rear Light Assembly RH) |
Apply battery voltage to the rear light assembly RH and check that the light illuminates.
| Tester Connection | Specified Condition |
|---|---|
|
*1: w/ Rear Fog Light *2: w/ Sequential Rear Turn Signal Light |
|
Click Location & Routing(g1)Location & Routingewd_type=routing;type=c;code=g1 Click Connector(g1)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly RHewd_type=component;type=c;code=g1;pinno=6,4,7,9,10 |
|
| Battery positive (+) - g1-6(B) | Taillight illuminates |
| Battery negative (-) - g1-4(E) | |
| Battery positive (+) - g1-7(B) | Rear fog light illuminates*1 |
| Battery negative (-) - g1-4(E) | |
| Battery positive (+) - g1-9(B) | Back up light illuminates |
| Battery negative (-) - g1-4(E) | |
| Battery positive (+) - g1-10(B) | Stop light illuminates*2 |
| Battery negative (-) - g1-4(E) | |
If the result is not as specified, replace the rear light assembly RH.
81595 3.INSPECT REAR LIGHT SOCKET AND WIRE LH
w/ Sequential Rear Turn Signal Light:
Inspect the rear light socket and wire LH.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (Rear Light Socket and Wire LH) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g2)Location & Routingewd_type=routing;type=c;code=g2 Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LHewd_type=component;type=c;code=g2;pinno=4,6,7,9,10 |
||
| g2-4(E) - A9 | Always | Below 1 Ω |
| g2-6(B) - A1 | ||
| g2-7(B) - A2 | ||
| g2-9(B) - A4 | ||
| g2-10(B) - A5 | ||
If the result is not as specified, replace the rear light socket and wire LH.
w/o Sequential Rear Turn Signal Light:
Inspect the rear light socket and wire LH.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (Rear Light Socket and Wire LH) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g2)Location & Routingewd_type=routing;type=c;code=g2 Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LHewd_type=component;type=c;code=g2;pinno=4,6,7,9 |
||
| g2-4(E) - A4 | Always | Below 1 Ω |
| g2-6(B) - A3 | ||
| g2-7(B) - A2 | ||
| g2-9(B) - A1 | ||
If the result is not as specified, replace the rear light socket and wire LH.
81585C 4.INSPECT REAR LIGHT SOCKET AND WIRE RH
w/ Rear Sequential Rear Turn Light :
Inspect the rear light socket and wire RH.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (Rear Light Socket and Wire RH) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g1)Location & Routingewd_type=routing;type=c;code=g1 Click Connector(g1)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly RHewd_type=component;type=c;code=g1;pinno=4,6,7,9,10 |
||
| g1-4(E) - A9 | Always | Below 1 Ω |
| g1-6(B) - A1 | ||
| g1-7(B) - A2 | ||
| g1-9(B) - A4 | ||
| g1-10(B) - A5 | ||
If the result is not as specified, replace the rear light socket and wire RH.
w/o Rear Sequential Rear Turn Light :
Inspect the rear light socket and wire RH.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (Rear Light Socket and Wire RH) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g1)Location & Routingewd_type=routing;type=c;code=g1 Click Connector(g1)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly RHewd_type=component;type=c;code=g1;pinno=4,6,7,9 |
||
| g1-4(E) - A4 | Always | Below 1 Ω |
| g1-6(B) - A3 | ||
| g1-7(B) - A2 | ||
| g1-9(B) - A1 | ||
If the result is not as specified, replace the rear light socket and wire RH.