Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468057 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY

a.

Disconnect the stop light switch assembly connector.


b.
E459190C02
1.479,0.083 1.885,0.323 0.406,0.24 1.302,1.375 1.135,1.927 true 2.25,1.385 2.458,1.875 true 2.063,1.396 1.906,1.938 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.563,0.115 1.99,0.333 0.427,0.219 10 false B43 2.458,1.927 2.625,2.094 0.167,0.167 10 false B 0.958,1.938 1.375,2.125 0.417,0.188 10 false GND 1.875,1.958 2.042,2.125 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B43)Location & Routing

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

B43-6 (B) - Body ground Ignition switch ON 11 to 14 V
B43-6 (B) - Body ground Ignition switch off Below 1 V
B43-7 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B43)Location & Routing

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

B43-2 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.


c.
E409580C50
1.51,0.083 1.927,0.385 0.417,0.302 2.313,1.24 2.896,0.938 true 2.135,1.26 2.49,1.875 true 1.927,1.271 2.281,1.885 true 1.24,1.865 1.698,1.292 true 0.865,1.948 1.49,1.281 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.594,0.135 2.052,0.333 0.458,0.198 10 false B43 2.969,0.833 3.313,1.073 0.344,0.24 10 false OUT 2.552,1.823 2.896,2.063 0.344,0.24 10 false GND 2.281,1.906 2.438,2.104 0.156,0.198 10 false L 1.063,1.896 1.406,2.135 0.344,0.24 10 false ACC 0.76,1.917 0.917,2.115 0.156,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Connect the stop light switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: 1GR-FE

*2: V35A-FTS

Click Location & Routing(B43)Location & Routing

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

B43-1 (OUT) - B43-2 (GND) Ignition switch off, brake pedal not depressed Below 1.5 V
B43-1 (OUT) - B43-2 (GND) Ignition switch off, brake pedal depressed 11 to 14 V
B43-3 (L) - B43-2 (GND) Ignition switch off, brake pedal not depressed Below 1.5 V
B43-3 (L) - B43-2 (GND) Ignition switch off, brake pedal depressed 11 to 14 V
B43-4 (ACC) - B43-2 (GND) Always 11 to 14 V
B43-5 (L) - B43-2 (GND) Ignition switch ON, brake pedal not depressed 7.5 to 14 V
B43-5 (L) - B43-2 (GND) Ignition switch ON, brake pedal depressed Below 1.5 V*1
B43-5 (L) - B43-2 (GND) Ignition switch ON, brake pedal depressed 0 to 1.5 V*2


If the result is not as specified, replace the stop light switch assembly.