Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0468135 NOISE FILTER G

AUDIO / VIDEO  NOISE FILTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 86011V 1.INSPECT RADIO SETTING CONDENSER

a.

With the radio setting condenser installed, check that there is no looseness or other abnormalities.


b.
E386542C12
1.594,0.417 2.073,0.333 true 2.125,0.229 2.281,0.427 0.156,0.198 10 false 1 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a
*a Radio Setting Condenser


Measure the resistance of the radio setting condenser according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground
·

Ignition switch off

·

High mounted stop light off

·

Window Defogger turned off


Below 1 Ω


If the result is not as specified, replace the radio setting condenser.


c.

Remove the bolt.


d.

Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.


e.
E211797C38
1.948,0.625 2.604,0.438 true 1.896,0.885 2.51,1.281 true 1.906,1.656 2.552,1.792 true 2.635,0.323 2.771,0.521 0.135,0.198 10 false 1 2.542,1.188 2.677,1.385 0.135,0.198 10 false 2 2.563,1.698 2.698,1.896 0.135,0.198 10 false 3 0.073,0 0.281,0.198 0.208,0.198 10 false *a
*a Radio Setting Condenser


Measure the resistance of the radio setting condenser according to the value(s) in the table below.

NOTICE:

Before measuring the resistance, be sure to use insulated probes to avoid a short circuit between the tester terminal and bracket.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2
·

Ignition switch off

·

High mounted stop light off

·

Window Defogger turned off


10 kΩ or higher
1 - 3 10 kΩ or higher


If the result is not as specified, replace the radio setting condenser.


f.
E211797C37
2.406,1.729 1.927,1.729 true 1.917,0.917 2.448,1.177 true 2.5,1.115 2.635,1.281 0.135,0.167 10 false 2 2.5,1.667 2.625,1.823 0.125,0.156 10 false 3 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a
*a Radio Setting Condenser


Measure the voltage of the radio setting condenser according to the value(s) in the table below.

NOTICE:

Before measuring the voltage, be sure to use insulated probes to avoid a short circuit between the tester terminal and bracket.


Standard Voltage:
Tester Connection Condition Specified Condition
2 - Body ground
·

Ignition switch ON

·

High mounted stop light off

·

Window Defogger turned off


Below 1 V
3 - Body ground Below 1 V
2 - Body ground
·

Ignition switch ON

·

High mounted stop light on

·

Window Defogger turned on


11 to 14 V
3 - Body ground 11 to 14 V


If the result is not as specified, replace the radio setting condenser.