Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM38G0E _58 Vehicle Interior _100612 SEAT BELT _0468155 FRONT SEAT OUTER BELT ASSEMBLY G

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 73220 1.INSPECT FRONT SEAT OUTER BELT ASSEMBLY LH

CAUTION:
B395346

·

The front seat outer belt assembly LH contains an internal pretensioner, so when performing component inspection, make sure not to accidentally connect the battery to the pretensioner connector terminal.

·

If the battery is connected to the pretensioner connector terminal, the pretensioner will activate, which could result in serious injury.



a.

Check the seat belt tension reducer operation.

i.
B475625C13
0.583,2.104 0.979,2.323 0.396,0.219 0.927,2.698 1.188,2.24 true 0.646,2.708 0.354,2.531 true 0.229,2.021 0.542,2.177 0.313,0.156 10 false *a 1.177,2.073 1.49,2.271 0.313,0.198 10 false IG 0.229,2.406 0.542,2.604 0.313,0.198 10 false L 0.656,2.135 1.115,2.333 0.458,0.198 10 false S13
*a Component without harness connected
(Front Seat Outer Belt Assembly LH)


Check the operating sound.

OK:
Tester Connection Specified Condition

Click Location & Routing(S13)Location & Routing

Click Connector(S13)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Tension Reducer LH (Front Seat Outer Belt Assembly LH)

S13-1 (IG) - battery positive (+)
S13-2 (L) - battery negative (-)
Operating sound is heard when the magnetized solenoid is attracting the plunger



ii.

Pull out the seat belt again, disconnect the negative (-) lead of the battery and allow the seat belt to retract. Listen to the operating sound again and check that the operating sound volume has increased.

If the result is not as specified, replace the front seat outer belt assembly LH.



b.
B491912C02
2.458,0.042 2.771,0.198 0.313,0.156 10 false *a 0.396,1.667 0.708,1.823 0.313,0.156 10 false *b 1.271,0.594 1.583,0.75 0.313,0.156 10 false *c
*a Unlock
*b Lock
*c 45°


Before installing the front seat outer belt assembly LH, check the ELR function.

NOTICE:

Do not disassemble the retractor.


i.

When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

If the result is not as specified, replace the front seat outer belt assembly LH.



Hide 73210 2.INSPECT FRONT SEAT OUTER BELT ASSEMBLY RH

CAUTION:
B395346

·

The front seat outer belt assembly RH contains an internal pretensioner, so when performing component inspection, make sure not to accidentally connect the battery to the pretensioner connector terminal.

·

If the battery is connected to the pretensioner connector terminal, the pretensioner will activate, which could result in serious injury.



a.

Check the seat belt tension reducer operation.

i.
B475625C14
0.583,2.104 0.979,2.323 0.396,0.219 0.927,2.698 1.188,2.24 true 0.646,2.708 0.354,2.531 true 0.229,2.021 0.542,2.177 0.313,0.156 10 false *a 1.177,2.073 1.49,2.271 0.313,0.198 10 false IG 0.229,2.406 0.542,2.604 0.313,0.198 10 false L 0.656,2.135 1.115,2.333 0.458,0.198 10 false Q20
*a Component without harness connected
(Front Seat Outer Belt Assembly RH)


Check the operating sound.

OK:
Tester Connection Specified Condition

Click Location & Routing(Q20)Location & Routing

Click Connector(Q20)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Tension Reducer RH (Front Seat Outer Belt Assembly RH)

Q20-1 (IG) - battery positive (+)
Q20-2 (L) - battery negative (-)
Operating sound is heard when the magnetized solenoid is attracting the plunger



ii.

Pull out the seat belt again, disconnect the negative (-) lead of the battery and allow the seat belt to retract. Listen to the operating sound again and check that the operating sound volume has increased.

If the result is not as specified, replace the front seat outer belt assembly RH.



b.
B491912C03
2.458,0.042 2.771,0.198 0.313,0.156 10 false *a 0.396,1.667 0.708,1.823 0.313,0.156 10 false *b 1.271,0.594 1.583,0.75 0.313,0.156 10 false *c
*a Unlock
*b Lock
*c 45°


Before installing the front seat outer belt assembly RH, check the ELR function.

NOTICE:

Do not disassemble the retractor.


i.

When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

If the result is not as specified, replace the front seat outer belt assembly RH.