Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468175 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69040A 1.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

a.
B610880C02
1.365,2.958 1.865,3.208 0.5,0.25 2.167,3.74 2.5,3.583 true 1.813,4.052 2.271,4.323 true 1.604,4.052 0.99,4.375 true 1.219,3.771 0.906,3.646 true 2.521,2.552 2.833,2.75 0.313,0.198 10 false *a 2,2.938 2.313,3.135 0.313,0.198 10 false *b 1.542,3 1.854,3.198 0.313,0.198 10 false N2 0.521,3 0.833,3.198 0.313,0.198 10 false *c 2.542,3.438 2.854,3.635 0.313,0.198 10 false UL 2.323,4.26 2.635,4.458 0.313,0.198 10 false E 0.573,4.292 1.052,4.542 0.479,0.25 10 false LSSR 0.698,3.5 1.01,3.698 0.313,0.198 10 false L
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock with Motor Assembly LH)


Check the operation of the door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(N2)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

Auxiliary battery positive (+) → Terminal N2-4 (L)
Auxiliary battery negative (-) → Terminal N2-1 (UL)
Locks
Auxiliary battery positive (+) → Terminal N2-1 (UL)
Auxiliary battery negative (-) → Terminal N2-4 (L)
Unlocks


If the result is not as specified, replace the front door lock with motor assembly LH.



b.

Check the operation of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

If the result is not as specified, replace the front door lock with motor assembly LH.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N2)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

N2-7 (E) - N2-8 (LSSR) Locked 10 kΩ or higher
N2-7 (E) - N2-8 (LSSR) Unlocked Below 1 Ω




c.
B610881C02
1.5,2.917 2,3.167 0.5,0.25 1.156,4.417 1.406,4.042 true 2.01,4.427 1.792,4.052 true 0.844,4.188 1.24,4.042 true 2.938,0.406 3.25,0.604 0.313,0.198 10 false *a 3.135,0.844 3.365,1.021 0.229,0.177 10 false *b 2.865,1.365 3.094,1.542 0.229,0.177 10 false *c 1.656,2.958 1.938,3.188 0.281,0.229 10 false N2 0.75,3 0.979,3.177 0.229,0.177 10 false *d 2.052,4.354 2.333,4.583 0.281,0.229 10 false E 0.604,4.104 0.885,4.333 0.281,0.229 10 false UL 1.01,4.385 1.292,4.615 0.281,0.229 10 false L
*a Unlock
*b Neutral
*c Lock
*d Component without harness connected
(Front Door Lock with Motor Assembly LH)


Check the operation of the door key lock and unlock switch. (for LHD)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N2)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

N2-9 (L) - N2-7 (E) Held to lock side Below 1 Ω
N2-9 (L) - N2-7 (E) Neutral or held to unlock side 10 kΩ or higher
N2-10 (UL) - N2-7 (E) Held to unlock side Below 1 Ω
N2-10 (UL) - N2-7 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly LH.



Hide 69040A 2.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

a.
B610882C01
1.469,2.979 1.969,3.229 0.5,0.25 1.917,3.698 2.417,3.25 true 2.177,3.75 2.594,3.75 true 2.167,4 2.583,4 true 1.979,4.042 2.479,4.313 true 1.448,4.052 1.146,4.333 true 0.802,3.979 1.219,3.979 true 0.823,3.729 1.24,3.729 true 1.51,3.708 0.583,3.333 true 2.271,2.271 2.583,2.469 0.313,0.198 10 false *a 1.698,2.573 2.01,2.771 0.313,0.198 10 false *b 1.646,3 1.958,3.198 0.313,0.198 10 false N2 0.844,3.063 1.156,3.26 0.313,0.198 10 false *c 2.49,3.115 2.802,3.313 0.313,0.198 10 false UL 2.656,3.625 2.969,3.823 0.313,0.198 10 false L 2.646,3.896 2.958,4.094 0.313,0.198 10 false E 0.99,4.281 1.302,4.479 0.313,0.198 10 false E 0.385,3.885 0.865,4.135 0.479,0.25 10 false LSSR 0.594,3.625 1.073,3.875 0.479,0.25 10 false DL 0.156,3.208 0.635,3.458 0.479,0.25 10 false UNDL 2.521,4.24 3,4.49 0.479,0.25 10 false DLSR
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock with Motor Assembly LH)


Check the operation of the front door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(N2)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

Auxiliary battery positive (+) → Terminal N2-1 (L)
Auxiliary battery negative (-) → Terminal N2-2 (UL)
Locks
Auxiliary battery positive (+) → Terminal N2-2 (UL)
Auxiliary battery negative (-) → Terminal N2-1 (L)
Unlocks
Auxiliary battery positive (+) → Terminal N2-4 (DL)
Auxiliary battery negative (-) → Terminal N2-3 (UNDL)
Sets
Auxiliary battery positive (+) → Terminal N2-3 (UNDL)
Auxiliary battery negative (-) → Terminal N2-4 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock with motor assembly LH.



b.

Check the operation of the door unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N2)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

N2-10 (LSSR) - N2-9 (E) Locked 10 kΩ or higher
N2-10 (LSSR) - N2-9 (E) Unlocked Below 1 Ω
N2-6 (DLSR) - N2-5 (E) Unset 10 kΩ or higher
N2-6 (DLSR) - N2-5 (E) Set Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly LH.



c.
B610883C02
1.469,2.917 1.969,3.167 0.5,0.25 0.833,4.167 1.417,4.031 true 1.083,4.417 1.604,4.052 true 1.792,4.042 2.25,4.427 true 2.042,0.854 2.354,1.052 0.313,0.198 10 false *a 2.208,2.198 2.417,2.406 0.208,0.208 10 true *b 0.615,2.99 0.927,3.188 0.313,0.198 10 false *c 1.646,2.958 1.958,3.156 0.313,0.198 10 false N2 2.323,4.333 2.635,4.531 0.313,0.198 10 false L 0.938,4.417 1.25,4.615 0.313,0.198 10 false UL 0.667,4.073 0.979,4.271 0.313,0.198 10 false E
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock with Motor Assembly LH)


Check the operation of the door key lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N2)Location & Routing

Click Connector(N2)Body>Front Door Wire LH>Front Door Lock with Motor Assembly LH

N2-7 (L) - N2-9 (E) Held to lock side Below 1 Ω
N2-7 (L) - N2-9 (E) Neutral or held to unlock side 10 kΩ or higher
N2-8 (UL) - N2-9 (E) Held to unlock side Below 1 Ω
N2-8 (UL) - N2-9 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly LH.



Hide 69030A 3.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (w/o Double Locking System)

a.
B610884C02
1.479,2.958 1.979,3.208 0.5,0.25 0.917,3.771 1.25,3.771 true 1.833,4.052 2.188,4.333 true 1.583,4.052 1.083,4.333 true 2.167,3.781 2.5,3.781 true 0.865,2.167 1.177,2.323 0.313,0.156 10 false *a 1.615,2.604 1.927,2.76 0.313,0.156 10 false *b 0.75,3.156 1.063,3.313 0.313,0.156 10 false *c 1.635,3 1.948,3.156 0.313,0.156 10 false M2 2.24,4.26 2.719,4.51 0.479,0.25 10 false LSSR 0.917,4.25 1.167,4.5 0.25,0.25 10 false E 0.75,3.667 1,3.917 0.25,0.25 10 false L 2.542,3.688 2.875,3.938 0.333,0.25 10 false UL
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock with Motor Assembly RH)


Check the operation of the door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(M2)Location & Routing

Click Connector(M2)Body>Front Door Wire RH>Front Door Lock with Motor Assembly RH

Auxiliary battery positive (+) → Terminal M2-4 (L)
Auxiliary battery negative (-) → Terminal M2-1 (UL)
Locks
Auxiliary battery positive (+) → Terminal M2-1 (UL)
Auxiliary battery negative (-) → Terminal M2-4 (L)
Unlocks


If the result is not as specified, replace the front door lock with motor assembly RH.



b.

Check the operation of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M2)Location & Routing

Click Connector(M2)Body>Front Door Wire RH>Front Door Lock with Motor Assembly RH

M2-7 (LSSR) - M2-8 (E) Locked 10 kΩ or higher
M2-7 (LSSR) - M2-8 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly RH.



c.
B610885C01
1.417,2.917 1.917,3.167 0.5,0.25 1.25,4.417 1.573,4.052 true 2.208,4.385 1.979,4.021 true 2.51,3.99 2.177,3.99 true 1.563,2.948 1.875,3.146 0.313,0.198 10 false M2 0.438,0.333 0.75,0.531 0.313,0.198 10 false *a 0.156,0.833 0.469,1.031 0.313,0.198 10 false *b 0.5,3 0.813,3.198 0.313,0.198 10 false *d 0.448,1.365 0.76,1.563 0.313,0.198 10 false *c 2.552,3.896 2.865,4.094 0.313,0.198 10 false UL 2.271,4.333 2.583,4.531 0.313,0.198 10 false L 1.094,4.375 1.406,4.573 0.313,0.198 10 false E
*a Unlock
*b Neutral
*c Lock
*d Component without harness connected
(Front Door Lock with Motor Assembly RH)


Check the operation of the door key lock and unlock switch. (for RHD)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M2)Location & Routing

Click Connector(M2)Body>Front Door Wire RH>Front Door Lock with Motor Assembly RH

M2-6 (L) - M2-8 (E) Held to lock side Below 1 Ω
M2-6 (L) - M2-8 (E) Neutral or held to unlock side 10 kΩ or higher
M2-5 (UL) - M2-8 (E) Held to unlock side Below 1 Ω
M2-5 (UL) - M2-8 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly RH.



Hide 69030A 4.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (w/ Double Locking System)

a.
B610886C01
1.469,2.948 1.958,3.198 0.49,0.25 2.135,3.708 2.583,3.5 true 2.177,3.938 2.5,4 true 1.99,4.031 2.417,4.333 true 1.448,4.042 1,4.333 true 1.25,3.771 0.833,3.771 true 1.219,3.979 0.802,3.979 true 1.49,3.74 0.833,3.5 true 2.5,3.167 1.875,3.708 true 1.042,2.302 1.354,2.458 0.313,0.156 10 false *a 1.646,2.563 1.958,2.719 0.313,0.156 10 false *b 0.771,3.083 1.083,3.24 0.313,0.156 10 false *c 1.615,2.979 1.927,3.135 0.313,0.156 10 false M2 2.625,3.385 3.104,3.625 0.479,0.24 10 false UNDL 2.563,3.917 3.042,4.156 0.479,0.24 10 false LSSR 2.479,4.26 2.958,4.5 0.479,0.24 10 false E 0.583,4.24 1.063,4.479 0.479,0.24 10 false DLSR 0.594,3.677 0.906,3.917 0.313,0.24 10 false UL 0.635,3.875 0.948,4.115 0.313,0.24 10 false E 0.656,3.406 0.969,3.646 0.313,0.24 10 false L 2.542,3.042 3.021,3.281 0.479,0.24 10 false DL
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock with Motor Assembly RH)


Check the operation of the front door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(M2)Location & Routing

Click Connector(M2)Body>Front Door Wire RH>Front Door Lock with Motor Assembly RH

Auxiliary battery positive (+) → Terminal M2-3 (L)
Auxiliary battery negative (-) → Terminal M2-4 (UL)
Locks
Auxiliary battery positive (+) → Terminal M2-4 (UL)
Auxiliary battery negative (-) → Terminal M2-3 (L)
Unlocks
Auxiliary battery positive (+) → Terminal M2-2 (DL)
Auxiliary battery negative (-) → Terminal M2-1 (UNDL)
Sets
Auxiliary battery positive (+) → Terminal M2-1 (UNDL)
Auxiliary battery negative (-) → Terminal M2-2 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock with motor assembly RH.