Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468176 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

a.
B610888C02
1.458,2.917 1.958,3.167 0.5,0.25 2.156,3.75 2.531,3.75 true 0.917,3.781 1.25,3.781 true 0.917,4.333 1.417,4.052 true 2.5,4.417 1.958,4.052 true 1.219,2.417 1.531,2.573 0.313,0.156 10 false *b 2.167,2.177 2.479,2.333 0.313,0.156 10 false *a 0.552,3.094 0.865,3.25 0.313,0.156 10 false *c 1.625,2.958 1.938,3.115 0.313,0.156 10 false P1 2.604,3.677 2.917,3.833 0.313,0.156 10 false UL 2.583,4.344 3.167,4.583 0.583,0.24 10 false LSSR 0.719,4.271 1.052,4.521 0.333,0.25 10 false E 0.708,3.688 1.042,3.938 0.333,0.25 10 false L
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock with Motor Assembly LH)


Check the operation of the door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(P1)Location & Routing

Click Connector(P1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

Auxiliary battery positive (+) → Terminal P1-4 (L)
Auxiliary battery negative (-) → Terminal P1-4 (L)
Locks
Auxiliary battery positive (+) → Terminal P1-1 (UL)
Auxiliary battery negative (-) → Terminal P1-4 (L)
Unlocks


If the result is not as specified, replace the rear door lock with motor assembly LH.



b.

Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(P1)Location & Routing

Click Connector(P1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

P1-6 (LSSR) - P1-9 (E) Locked 10 kΩ or higher
P1-6 (LSSR) - P1-9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly LH.



Hide 69050A 2.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH (w/o Double Locking System)

a.
B610890C02
1.417,2.833 1.917,3.083 0.5,0.25 2.167,3.75 2.667,3.75 true 1.458,4.063 1.458,4.396 true 1.958,4.063 1.958,4.396 true 0.74,3.771 1.24,3.771 true 1.073,2.156 1.385,2.313 0.313,0.156 10 false *a 2.073,2.438 2.385,2.594 0.313,0.156 10 false *b 0.313,2.979 0.625,3.135 0.313,0.156 10 false *c 1.573,2.885 1.885,3.042 0.313,0.156 10 false O1 2.719,3.646 3.031,3.802 0.313,0.156 10 false UL 1.281,4.438 1.729,4.635 0.448,0.198 10 false LSSR 1.927,4.427 2.115,4.615 0.188,0.188 10 false E 0.604,3.708 0.854,3.948 0.25,0.24 10 false L
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock with Motor Assembly RH)


Check the operation of the door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

Auxiliary battery positive (+) → Terminal O1-4 (L)
Auxiliary battery negative (-) → Terminal O1-1 (UL)
Locks
Auxiliary battery positive (+) → Terminal O1-1 (UL)
Auxiliary battery negative (-) → Terminal O1-4 (L)
Unlocks


If the result is not as specified, replace the rear door lock with motor assembly RH.



b.

Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

O1-9 (LSSR) - O1-6 (E) Locked 10 kΩ or higher
O1-9 (LSSR) - O1-6 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly RH.



Hide 69060A 3.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

a.
B610889C01
1.5,2.938 1.917,3.188 0.417,0.25 2.167,3.75 2.5,3.75 true 2.167,4 2.5,4 true 1.906,3.719 2.5,3.333 true 1.979,4.042 2.417,4.333 true 1.458,4.052 1,4.417 true 1.25,4.031 0.917,4.031 true 1.25,3.792 0.917,3.792 true 1.5,3.719 0.76,3.448 true 2.177,2.583 2.49,2.74 0.313,0.156 10 false *a 1.583,2.719 1.896,2.875 0.313,0.156 10 false *b 0.844,3.083 1.156,3.24 0.313,0.156 10 false *c 1.615,2.99 1.927,3.146 0.313,0.156 10 false P2 2.552,3.656 3.083,3.917 0.531,0.26 10 false UNDL 2.542,3.896 3.021,4.146 0.479,0.25 10 false DLSR 2.542,3.208 2.854,3.365 0.313,0.156 10 false DL 2.479,4.26 2.958,4.51 0.479,0.25 10 false E 0.583,4.333 1.063,4.583 0.479,0.25 10 false LSSR 0.76,3.948 1.24,4.198 0.479,0.25 10 false E 0.75,3.688 1.229,3.938 0.479,0.25 10 false L 0.49,3.323 0.969,3.573 0.479,0.25 10 false UL
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock with Motor Assembly LH)


Check the operation of the door lock motor and double lock motor.

i.

Apply auxiliary battery voltage and check the operation of the rear door lock motor and double lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(P2)Location & Routing

Click Connector(P2)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

Auxiliary battery positive (+) → Terminal P2-4 (L)
Auxiliary battery negative (-) → Terminal P2-3 (UL)
Locks
Auxiliary battery positive (+) → Terminal P2-3 (UL)
Auxiliary battery negative (-) → Terminal P2-4 (L)
Unlocks
Auxiliary battery positive (+) → Terminal P2-2 (DL)
Auxiliary battery negative (-) → Terminal P2-1 (UNDL)
Sets
Auxiliary battery positive (+) → Terminal P2-1 (UNDL)
Auxiliary battery negative (-) → Terminal P2-2 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock with motor assembly LH.



b.

Check the operation of the unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(P2)Location & Routing

Click Connector(P2)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

P2-9 (LSSR) - P2-10 (E) Locked 10 kΩ or higher
P2-9 (LSSR) - P2-10 (E) Unlocked Below 1 Ω
P2-5 (DLSR) - P2-6 (E) Unset 10 kΩ or higher
P2-5 (DLSR) - P2-6 (E) Set Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly LH.



Hide 69050A 4.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH (w/ Double Locking System)

a.
B610891C01
1.417,2.958 1.917,3.208 0.5,0.25 0.833,3.5 1.5,3.708 true 0.917,3.781 1.25,3.781 true 0.906,4.042 1.24,4.042 true 1,4.417 1.427,4.042 true 2.167,3.75 2.5,3.75 true 2.177,4 2.51,4 true 1.979,4.042 2.417,4.333 true 1.917,3.708 2.5,3.417 true 1.323,2.563 1.635,2.719 0.313,0.156 10 false *a 1.927,2.708 2.24,2.865 0.313,0.156 10 false *b 1,3.083 1.313,3.24 0.313,0.156 10 false *c 1.583,3 1.896,3.156 0.313,0.156 10 false O2 0.417,3.375 0.958,3.583 0.542,0.208 10 false UNDL 0.667,3.688 0.948,3.854 0.281,0.167 10 false DL 0.75,3.948 1.031,4.115 0.281,0.167 10 false E 0.573,4.344 1.073,4.594 0.5,0.25 10 false DLSR 2.573,3.646 2.865,3.854 0.292,0.208 10 false UL 2.552,3.292 2.844,3.5 0.292,0.208 10 false L 2.479,4.229 2.667,4.417 0.188,0.188 10 false E 2.563,3.906 3.021,4.156 0.458,0.25 10 false LSSR
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock with Motor Assembly RH)


Check the operation of the door lock motor and double lock motor.

i.

Apply auxiliary battery voltage and check the operation of the rear door lock with motor assembly and double lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

Auxiliary battery positive (+) → Terminal O2-2 (L)
Auxiliary battery negative (-) → Terminal O2-1 (UL)
Locks
Auxiliary battery positive (+) → Terminal O2-1 (UL)
Auxiliary battery negative (-) → Terminal O2-2 (L)
Unlocks
Auxiliary battery positive (+) → Terminal O2-4 (DL)
Auxiliary battery negative (-) → Terminal O2-3 (UNDL)
Sets
Auxiliary battery positive (+) → Terminal O2-3 (UNDL)
Auxiliary battery negative (-) → Terminal O2-4 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock with motor assembly RH.



b.

Check the operation of the unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

O2-5 (LSSR) - O2-6 (E) Locked 10 kΩ or higher
O2-5 (LSSR) - O2-6 (E) Unlocked Below 1 Ω
O2-9 (DLSR) - O2-10 (E) Unset 10 kΩ or higher
O2-9 (DLSR) - O2-10 (E) Set Below 1 Ω


If the result is not as specified, replace the rear door lockwith motor assembly RH.