Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468177 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69350P 1.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY (w/o Power Back Door)

a.
B577577C05
1.521,3.354 2.021,3.552 0.5,0.198 1.521,1.323 1,1.323 true 1.563,3.135 1.115,3.135 true 1.344,4.25 1.583,4.01 true 2.219,4.25 1.99,4.01 true 1.792,4.25 1.792,4.021 true 0.354,2.24 0.667,2.438 0.313,0.198 10 false *c 1.073,3.625 1.385,3.823 0.313,0.198 10 false *a 0.375,0.125 0.688,0.323 0.313,0.198 10 false *b 1.25,4.208 1.5,4.406 0.25,0.198 10 false + 1.646,4.271 2.26,4.469 0.615,0.198 10 false ACT- 2.271,4.188 2.885,4.385 0.615,0.198 10 false ACT+ 0.938,3.021 1.25,3.219 0.313,0.198 10 false *1 0.823,1.24 1.135,1.438 0.313,0.198 10 false *1 1.698,3.344 2.01,3.542 0.313,0.198 10 false g4
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Lock
*c Unlock
*1 Latch


Check the operation of the door lock motor.

i.

Move the door lock to the lock position.


ii.

Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(g4)Location & Routing

Click Connector(g4)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Auxiliary Battery positive (+) → g4-1 (ACT+)
Auxiliary Battery negative (-) → g4-2 (ACT-)
Unlocks


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



b.

Check the operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g4)Location & Routing

Click Connector(g4)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g4-2 (ACT-) - g4-3 (+) Locked 10 kΩ or higher
g4-2 (ACT-) - g4-3 (+) Unlocked Below 1 Ω


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



Hide 69350P 2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY (w/ Power Back Door)

a.
B577572C03
1.51,2.094 1.927,2.344 0.417,0.25 1.896,2.792 2.271,2.792 true 1.146,2.792 1.521,2.792 true 1.01,0.948 1.24,1.156 0.229,0.208 10 true *b 1.708,0.948 1.938,1.156 0.229,0.208 10 true *a 0.719,2.177 0.948,2.385 0.229,0.208 10 false *c 2.333,2.719 2.646,2.917 0.313,0.198 10 false M- 0.917,2.729 1.229,2.927 0.313,0.198 10 false M+ 1.01,1.781 1.24,1.99 0.229,0.208 10 true *a 1.76,1.792 1.99,2 0.229,0.208 10 true *b 1.635,2.104 1.865,2.313 0.229,0.208 10 false g5
*a Open Operation Direction
*b Close Operation Direction
*c Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)


Check the operation.

i.

Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition

Click Location & Routing(g5)Location & Routing

Click Connector(g5)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Auxiliary battery positive (+) → g5-1 (M-)
Auxiliary battery negative (-) → g5-2 (M+)
Open Operation
Auxiliary battery positive (+) → g5-2 (M+)
Auxiliary battery negative (-) → g5-1 (M-)
Close Operation


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



b.
B577573C15
1.479,1.917 1.979,2.167 0.5,0.25 1.99,0.469 2.135,0.146 2.135,0.146 2.365,0.146 true 1.125,2.667 1.49,2.667 true 1.958,2.667 2.323,2.667 true 1.542,0.406 1.448,0.135 1.448,0.135 1.281,0.135 true 0.49,0.531 1.281,0.708 0.792,0.177 10 false 37°26' 0.792,0.063 1.635,0.313 0.844,0.25 10 false 37°23' 2.375,0.083 3.052,0.281 0.677,0.198 10 false 13°43' 0.51,0.844 0.823,1.042 0.313,0.198 10 false *a 1.052,0.313 1.365,0.51 0.313,0.198 10 false *b 1.802,0.229 2.115,0.427 0.313,0.198 10 false *c 2.104,0.344 2.396,0.51 0.292,0.167 10 false *d 0.75,2.01 1.063,2.208 0.313,0.198 10 false *e 2.365,2.583 2.823,2.781 0.458,0.198 10 false CLS 1.01,2.604 1.469,2.802 0.458,0.198 10 false E 1.656,1.938 1.969,2.135 0.313,0.198 10 false g6
*a Open Position
*b Half-latch Position
*c Full-latch Position
*d Overstroke Position
*e Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)


Check the resistance of the half latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g6-1 (E) - g6-3 (CLS) Open position Below 1 Ω
g6-1 (E) - g6-3 (CLS) Open position → Half-latch position Below 1 Ω → 10 kΩ or higher
g6-1 (E) - g6-3 (CLS) Half-latch position 10 kΩ or higher
g6-1 (E) - g6-3 (CLS) Full-latch position 10 kΩ or higher
g6-1 (E) - g6-3 (CLS) Overstroke position 10 kΩ or higher


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



c.
B577573C16
1.479,1.917 1.979,2.167 0.5,0.25 1.99,0.469 2.135,0.146 2.135,0.146 2.365,0.146 true 1.125,2.667 1.49,2.667 true 1.542,2.896 1.219,3.156 true 1.542,0.406 1.448,0.135 1.448,0.135 1.281,0.135 true 0.49,0.531 1.281,0.708 0.792,0.177 10 false 37°26' 0.792,0.063 1.635,0.313 0.844,0.25 10 false 37°23' 2.375,0.083 3.052,0.281 0.677,0.198 10 false 13°43' 0.51,0.844 0.823,1.042 0.313,0.198 10 false *a 1.052,0.313 1.365,0.51 0.313,0.198 10 false *b 1.802,0.229 2.115,0.427 0.313,0.198 10 false *c 2.094,0.354 2.385,0.521 0.292,0.167 10 false *d 0.75,2.01 1.063,2.208 0.313,0.198 10 false *e 0.948,3.104 1.406,3.302 0.458,0.198 10 false CTY 1.01,2.604 1.469,2.802 0.458,0.198 10 false E 1.635,1.938 1.948,2.135 0.313,0.198 10 false g6
*a Open Position
*b Half-latch Position
*c Full-latch Position
*d Overstroke Position
*e Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)


Check the resistance of the full latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g6-4 (CTY) - g6-1 (E) Open position Below 1 Ω
g6-4 (CTY) - g6-1 (E) Half-latch position Below 1 Ω
g6-4 (CTY) - g6-1 (E) Half-latch position → Full-latch position Below 1 Ω → 10 kΩ or higher
g6-4 (CTY) - g6-1 (E) Full-latch position 10 kΩ or higher
g6-4 (CTY) - g6-1 (E) Overstroke position 10 kΩ or higher


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



d.
B577573C17
1.49,1.958 1.99,2.208 0.5,0.25 1.99,0.469 2.135,0.146 2.135,0.146 2.365,0.146 true 1.125,2.667 1.49,2.667 true 1.542,0.406 1.448,0.135 1.448,0.135 1.281,0.135 true 1.792,2.615 2.25,2.167 2.25,2.167 2.417,2.167 true 0.49,0.531 1.281,0.708 0.792,0.177 10 false 37°26' 0.792,0.063 1.635,0.313 0.844,0.25 10 false 37°23' 2.375,0.083 3.052,0.281 0.677,0.198 10 false 13°43' 0.51,0.844 0.823,1.042 0.313,0.198 10 false *a 1.052,0.313 1.365,0.51 0.313,0.198 10 false *b 1.802,0.229 2.115,0.427 0.313,0.198 10 false *c 2.094,0.354 2.385,0.521 0.292,0.167 10 false *d 0.75,2.01 1.063,2.208 0.313,0.198 10 false *e 2.469,2.063 2.927,2.26 0.458,0.198 10 false POLE 1.01,2.604 1.469,2.802 0.458,0.198 10 false E 1.656,1.969 2.115,2.167 0.458,0.198 10 false g6
*a Open Position
*b Half-latch Position
*c Full-latch Position
*d Overstroke Position
*e Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)


Check the resistance of the pawl switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g6-2 (POLE) - g6-1 (E) Open position 10 kΩ or higher
g6-2 (POLE) - g6-1 (E) Between open position and half-latch position 10 kΩ or higher → Below
g6-2 (POLE) - g6-1 (E) Half-latch position 10 kΩ or higher
g6-2 (POLE) - g6-1 (E) Between half-latch position and full-latch position 10 kΩ or higher → Below 1Ω
g6-2 (POLE) - g6-1 (E) Full-latch position 10 kΩ or higher
g6-2 (POLE) - g6-1 (E) Overstroke position 10 kΩ or higher


If the result is not as specified, replace the back door lock with courtesy light switch assembly.



e.

Check the operation of the selector switch.

i.
B577574C04
1.469,1.99 1.969,2.24 0.5,0.25 1.031,2.667 1.49,2.667 true 1.958,2.844 2.417,2.844 true 1.073,0.448 1.385,0.646 0.313,0.198 10 false *a 0.813,2.177 1.125,2.375 0.313,0.198 10 false *b 2.469,2.771 2.917,2.979 0.448,0.208 10 false OPN 0.896,2.594 1.302,2.802 0.406,0.208 10 false E 1.635,2 1.948,2.198 0.313,0.198 10 false g6
*a Sector Gear in Neutral Position
*b Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g6-6 (OPN) - g6-1 (E) Selector gear in neutral position
(Selector switch on)
Below 1 Ω
g6-6 (OPN) - g6-1 (E) Selector gear not in neutral position
(Selector switch off)
10 kΩ or higher


If the result is not as specified, replace the back door lock with courtesy light switch assembly.