Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR OPENER SWITCH
RM38G0E _59 Vehicle Exterior _100887 DOOR / HATCH _0468196 BACK DOOR OPENER SWITCH G

DOOR / HATCH  BACK DOOR OPENER SWITCH  INSPECTION  


PROCEDURE

Hide 812D0 1.INSPECT LICENSE PLATE LIGHT ASSEMBLY WITH BACK DOOR OPENER SWITCH

a.
B611075C04
2.417,0.333 2.917,0.583 0.5,0.25 2.5,1.167 2.229,1.594 true 2.719,1.177 3.01,1.573 true 0.729,1.021 0.927,1.198 0.198,0.177 10 true *a 0.083,1.313 0.26,1.469 0.177,0.156 10 false *b 0.125,0.063 0.438,0.219 0.313,0.156 10 false *c 2.604,0.354 2.906,0.563 0.302,0.208 10 false g3 2.156,1.615 2.313,1.781 0.156,0.167 10 false E 2.958,1.615 3.198,1.781 0.24,0.167 10 false UL
*a Pushed (ON)
*b Not Pushed (OFF)
*c Component without harness connected
(License Plate Light Assembly with Back Door Opener Switch)


Check the operation of the open switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(g3)Location & Routing

Click Connector(g3)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>License Plate Light Assembly with Back Door Opener Switch

g3-3 (UL) - g3-4 (E) Back door opener switch pushed (ON) Below 1 Ω
g3-3 (UL) - g3-4 (E) Back door opener switch not pushed (OFF) 10 kΩ or higher


If the result is not as specified, replace the license plate light assembly with back door opener switch.



b.
B611076C03
2.417,0.333 2.917,0.583 0.5,0.25 2.333,1.156 2.167,1.49 true 2.521,1.177 2.594,1.5 true 0.917,0.729 1.104,0.896 0.188,0.167 10 true *a 0.313,1.177 0.5,1.333 0.188,0.156 10 true *b 0.063,0.073 0.375,0.229 0.313,0.156 10 false *c 2.583,0.354 2.823,0.552 0.24,0.198 10 false g3 2.135,1.563 2.375,1.76 0.24,0.198 10 false L 2.563,1.542 2.802,1.74 0.24,0.198 10 false E
*a Pushed (ON)
*b Not Pushed (OFF)
*c Component without harness connected
(License Plate Light Assembly with Back Door Opener Switch)


Check the operation of the lock switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(g3)Location & Routing

Click Connector(g3)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>License Plate Light Assembly with Back Door Opener Switch

g3-5 (L) - g3-4 (E) Back door opener switch pushed (ON) Below 1 Ω
g3-5 (L) - g3-4 (E) Back door opener switch not pushed (OFF) 10 kΩ or higher


If the result is not as specified, replace the license plate light assembly with back door opener switch.