Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM38G0E _59 Vehicle Exterior _100887 DOOR / HATCH _0468264 POWER BACK DOOR SYSTEM U

DOOR / HATCH  POWER BACK DOOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

According to the display on the GTS, read the Data List.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Total distance traveled 0 to 16777215 Same as actual total distance traveled For the unit, refer to "Total Distance Traveled - Unit"
Total Distance Traveled - Unit Total Distance Traveled - unit km or mile km: km
mile: mile
-
Back Door Lock Status Back door condition signal Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked
-
Half Latch Switch Latch switch signal ON or OFF ON: Back door lock motor open-latched
OFF: Back door lock motor full-latched or half-latched
-
Closer Position Switch Initial switch signal ON or OFF ON: Back door lock sector gear in center position (Initial switch on)
OFF: Back door lock sector gear out of center position (Initial switch off)
-
Pawl Switch Pawl switch signal ON or OFF ON: Back door lock motor open-latched
OFF: Back door lock motor except open latched
-
Courtesy Switch Back door courtesy switch signal ON or OFF ON: Back door open
OFF: Back door closed
-
PBD Main Switch Power back door ON/OFF signal ON or OFF Current customize setting displayed -
PBD Close Switch Power back door control switch assembly signal ON or OFF ON: Power back door control switch assembly pushed
OFF: Power back door control switch assembly not pushed
-
IG Switch Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
"OFF" is also displayed for this item when the ignition switch to ACC.
Kick Sensor Function Status of the hands free power back door function ON or OFF ON: Hands free power back door ON
OFF: Hands free power back door off
w/ Hands Free Power Back Door
Close and Lock Switch Door control switch signal ON or OFF ON: Door control switch pressed
OFF: Door control switch not pressed
-
Door Lock Signal Back door condition signal Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked
-
PBD Touch Sensor RH Power back door sensor assembly RH signal ON, OFF or Open ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed
Open: Power back door sensor assembly RH circuit open
-
PBD Touch Sensor LH Power back door sensor assembly LH signal ON, OFF or Open ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed
Open: Power back door sensor assembly LH circuit open
-
Correction of Back Door Position Correction of back door position Not Complied With or Complied With Not Complied With: not complied with
Complied With: complied with
-
Kick Sensor Status Kick Sensor condition signal Normal, Sensitivity Low (Noise), Stop (Foreign Objects), Sensitivity Low (Noise) & Stop (Foreign Objects), Stop (Battery Protection), Sensitivity Low (Noise) & Stop (Battery Protection), Stop (Foreign Objects) & Stop (Battery Protection) or Sensitivity Low (Noise) & Stop (Foreign Objects) & Stop (Battery Protection) Normal: Kick sensor detection status normal
Sensitivity Low (Noise): Kick sensor detection sensitivity decreased due to noise
Stop (Foreign Objects): Kick sensor detection stopped due to foreign objects
Sensitivity Low (Noise) & Stop (Foreign Objects): Kick sensor sensitivity decreased due to noise and detection stopped due to foreign objects
Stop (Battery Protection): Kick sensor detection stopped due to battery protection
Sensitivity Low (Noise) & Stop (Battery Protection): Kick sensor sensitivity decreased due to noise and detection stopped due to battery protection
Stop (Foreign Objects) & Stop (Battery Protection): Kick sensor detection stopped due to foreign objects and battery protection
Sensitivity Low (Noise) & Stop (Foreign Objects) & Stop (Battery Protection): Kick sensor sensitivity decreased due to noise and detection stopped due to foreign objects and battery protection
w/ Hands Free Power Back Door
Opened Number of Times Number of times for back door opened 0 to 214783647 Number of times for back door opened -
Closed Number of Times Number of times for back door closed 0 to 214783647 Number of times for back door closed -
PBD SW Operating Condition Setting Back door control switch operation ON or 0.8s Current customize setting displayed -
PBD Buzzer Function Status of the the power back door buzzer ON or OFF Current customize setting displayed -
PBD Assist Close Function Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. ON or OFF Current customize setting displayed -
PBD Assist Open Function Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated. ON or OFF Current customize setting displayed -
PBD Door Unlock with One Motion Setting Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly). Back Door or All Doors Current customize setting displayed -
PBD Wireless Function Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). ON or OFF Current customize setting displayed -
PBD Wireless One Motion Function Wireless one motion function ON or OFF Current customize setting displayed -
PBD Wireless SW Setting Wireless operation setting condition Time ON, 2 Times ON or Long Current customize setting displayed -
PBD Kick Sensor Sensitivity Adjust Function that changes the sensitivity of the kick sensor. Normal, +1, +2 or Unknown Current customize setting displayed w/ Hands Free Power Back Door
Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Lock Position Status Back door lock position signal Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked
-
Back Door Courtesy Switch Status Back door courtesy light switch signal Close or Open Close: Back door closed
Open: Back door open
-
Back Door Operation Switch (Instrument) Power back door control switch signal ON or OFF ON: Power back door control switch on
OFF: Power back door control switch off
-


ACTIVE TEST


HINT:

Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

According to the display on GTS perform the "Active Test".

Body Electrical > Back Door > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PBD Motor (Open) Power back door motor operation Start -
PBD Motor (Close) Power back door motor operation Start -
PBD Buzzer (Small Volume) Power back door warning buzzer sound (small volume) Start -
PBD Buzzer (Middle Volume) Power back door warning buzzer sound (Middle volume) Start -
PBD Buzzer (Large Volume) Power back door warning buzzer sound (Large volume) Start -
PBD Release Closer Latch release operation Start -
Courtesy Lamp Power back door close switch light condition Start -