Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM38G0E _59 Vehicle Exterior _100887 DOOR / HATCH _0468264 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B220487  Kick Sensor LIN Communication Circuit Missing Message  


DESCRIPTION

The multiplex network door ECU communicates with the kick door control sensor assembly via LIN communication. If a communication error with the ECU, or an open or short on the LIN communication line is detected, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B220487 Kick Sensor LIN Communication Circuit Missing Message LIN communication error or open/short on communication line
·

Kick door control sensor assembly

·

Multiplex network door ECU

·

Harness or connector


Back Door A

WIRING DIAGRAM

E464753E03
5.302,1.625 5.76,1.823 0.458,0.198 10 false LIN 3.594,1.625 4.052,1.823 0.458,0.198 10 false MPX1 4.135,1.625 4.594,1.823 0.458,0.198 10 false T1 5.198,2.823 6.792,3.208 1.594,0.385 10 false Kick Door Control Sensor Assembly 5.219,2.646 5.677,2.844 0.458,0.198 10 false e5 2.542,2.688 6.521,2.885 3.979,0.198 10 false Multiplex Network Door ECU 2.792,2.177 3.25,2.375 0.458,0.198 10 false GND 2.823,1.063 3.281,1.26 0.458,0.198 10 false B 2.458,2.198 2.917,2.396 0.458,0.198 10 false T3 2.458,1.073 2.917,1.271 0.458,0.198 10 false T4 1.042,0.5 1.5,0.698 0.458,0.198 10 false PBD 2.042,0.323 3.438,0.667 1.396,0.344 10 false from Battery 5.094,1.438 5.552,1.635 0.458,0.198 10 false 1 4.135,1.417 4.594,1.615 0.458,0.198 10 false 18 2.479,0.875 2.938,1.073 0.458,0.198 10 false 5 2.479,1.979 2.938,2.177 0.458,0.198 10 false 4 0.646,3.438 4.625,3.635 3.979,0.198 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting, make sure that the kick door control sensor is not damaged.

·

Before troubleshooting, be sure to read Precautions for Hands Free Power Back Door.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>PRECAUTION

·

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the T3 multiplex network door ECU connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T3)Location & Routing

Click Connector(T3)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECU

T3-4 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(T4)Location & Routing

Click Connector(T4)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECU

T4-5 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - KICK DOOR CONTROL SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - KICK DOOR CONTROL SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the T1 multiplex network door ECU connector.


b.

Disconnect the e5 kick door control sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T1,e5)Location & Routing

Click Connector(T1)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Multiplex Network Door ECU

Click Connector(e5)Body>Rear Bumper Wire>Kick Door Control Sensor Assembly

T1-18 (MPX1) - e5-1 (LIN) Always 10 kΩ or higher
T1-18 (MPX1) or e5-1 (LIN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.REPLACE KICK DOOR CONTROL SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE KICK DOOR CONTROL SENSOR ASSEMBLY
a.

Temporarily replace the kick door control sensor assembly with a new or normally functioning one.

HINT:

Click hereVehicle Exterior>DOOR / HATCH>KICK SENSOR>REMOVAL



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
50002 489

Result:
Proceed to
NEXT



NEXT

5.REPRODUCE DTC
5.REPRODUCE DTC
a.

Turn the ignition switch to ON and wait for at least 10 seconds.

Body Electrical > Back Door > Trouble Codes
50001 489

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Disconnect the e5 kick door control sensor assembly connector.


b.

Wait for approximately 60 seconds.


c.

Check for DTCs.

Body Electrical > Back Door > Trouble Codes
50001 489

Result:
Result Proceed to
B220487 is output A
B220487 is not output B



A

REPLACE MULTIPLEX NETWORK DOOR ECU

B

END (KICK DOOR CONTROL SENSOR ASSEMBLY WAS DEFECTIVE)