Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › AUTOMATIC HIGH BEAM SYSTEM
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0468607 AUTOMATIC HIGH BEAM SYSTEM Y

ADVANCED DRIVER ASSISTANCE SYSTEM  AUTOMATIC HIGH BEAM SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the automatic high beam system.


·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V



If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication system DTCs are not output.



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTC*

NG

5.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433

b.

Clear the DTCs.

Body Electrical > Front Recognition Camera (Front Lighting Control) > Clear DTCs
50002 433

c.

Recheck for DTCs by simulating the operation indicated by the DTCs.

Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433

Result:
Result Proceed to
Malfunction is duplicated but DTCs arenot output A
Malfunction cannot be duplicated and DTCs are not output B
DTCs are output C



A

6.CHECK VEHICLE CONTROL HISTORY*

B

C

6.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Front Recognition Camera (Front Lighting Control) > Utility
Tester Display
Vehicle Control History (RoB)
50005 433 55
NOTICE:

Make sure to record the output Vehicle Control History.



Result:
Result Proceed to
Vehicle Control History codes are not output A
Vehicle Control History code X2020 and/or X204D is output B
Vehicle Control History codes other than X2020 and X204D are output C



A

7.PROBLEM SYMPTOMS TABLE

B

GO TO VEHICLE CONTROL HISTORY (Check Details of Code X2020 or X204D)

C

11.CHECK VEHICLE CONTROL HISTORY* (FRONT RECOGNITION CAMERA (FRONT LIGHTING CONTROL))
7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

11.CHECK VEHICLE CONTROL HISTORY* (FRONT RECOGNITION CAMERA (FRONT LIGHTING CONTROL))
a.

Clear Vehicle Control History

i.

Clear the Vehicle Control History.

Body Electrical > Front Recognition Camera (Front Lighting Control) > Utility
Tester Display
Vehicle Control History (RoB)
50005 433 55


b.

Check Vehicle Control History

i.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Front Recognition Camera (Front Lighting Control) > Utility
Tester Display
Vehicle Control History (RoB)
50005 433 55


Result:
Result Proceed to
Vehicle Control History (RoB) codes are not output A
Vehicle Control History (RoB) codes are output B



A

B