Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0468606 ADAPTIVE HIGH BEAM SYSTEM D

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  OPERATION CHECK  


ADAPTIVE HIGH BEAM SYSTEM OPERATION CHECK


E366183C01
2.146,0.417 2.323,0.417 2.323,0.417 2.542,0.76 false 0.292,0.344 0.604,0.542 0.313,0.198 10 false *a 1.969,0.333 2.281,0.531 0.313,0.198 10 false *b
*a Adaptive High Beam Indicator Light on Combination Meter Assembly
*b Auto High Beam Switch Indicator


NOTICE:

Make sure that the customize settings are set to default when performing the adaptive high beam system operation check.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>CUSTOMIZE PARAMETERS


a.

Check the operation of the adaptive high beam indicator light.

i.

Turn the ignition switch to ON.


ii.

Turn the light control switch to the AUTO or head position.


iii.

Press the auto high beam switch (indicator illuminates).


iv.

Check that the adaptive high beam indicator illuminates.

NOTICE:
·

If the forward recognition camera cannot operate due to high vehicle interior temperatures, bad weather (rain, fog, etc.) or fogged up or dirty glass, the AHS will not operate and the adaptive high beam indicator will not illuminate.

·

When the cable is disconnected from the negative (-) battery terminal, the adaptive high beam system may not operate until the vehicle steering sensor zero point calibration has been performed. After reconnecting the cable, drive the vehicle to initialize the steering sensor zero point value.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION

·

If the temperature of the forward recognition camera is excessively high, or performing the forward recognition camera axis calibration due a change in the attitude of the vehicle, such as when fully loaded, the adaptive high beam indicator may not turn on and consequently the adaptive high beam system may not operate.





b.

When the following conditions are met while the adaptive high beam system is on, after a short period of time the high beam headlights will turn on.

·

The vehicle speed is more than approximately 15 km/h (9 mph).

·

The area in front of the vehicle is dark.

·

There are no oncoming vehicles with headlights on.

·

There are no preceding vehicles with taillights on.

·

There are few streetlights along the street ahead.


i.

The high beam control mode changes in accordance with vehicle speed.

Illumination Mode Description Vehicle Speed
Except Europe Europe
Residential Area Mode At low speeds, in consideration of the drivers field of vision, the illuminated area is widened. The brightness of the headlights is adjusted to ensure that pedestrians are visible while not being dazzled. Reduces illumination of the side of the road. 15 to 30 km/h
(9 to 19 mph)
15 to 30 km/h
(9 to 19 mph)
Normal Mode At medium speeds, the illuminated area in front of the vehicle is extended and necessary areas to the left and right of the vehicle are illuminated. 30 to 80 km/h
(19 to 50 mph)
30 to 120 km/h
(19 to 75 mph)
High Speed Mode At high speeds, the illuminated area in front of the vehicle is extended and increased in brightness and the additional high beams are used. 80 km/h or more
(50 mph or more)
120 km/h or more
(75 mph or more)



c.

When the following conditions are met while the adaptive high beam system is on, cut-off line tilt control (function that adjusts the upper illumination area of the low beam headlights) will operate.

·

Vehicle speed is more than approximately 30 km/h (19 mph).

·

The area in front of the vehicle is dark.

·

There are preceding vehicles with taillights on.

·

There are few streetlights along the street ahead.


HINT:

The cut-off line tilt control does not operate when the front wipers are operating in LO or faster.



d.

When the following conditions are met while the adaptive high beam function is operating, after a short period of time the brightness and illumination area of the high beams will change according to the detected conditions.

·

Vehicle speed is more than approximately 15 km/h (9 mph).

·

The area in front of the vehicle is dark.

·

There are oncoming vehicles with headlights on.

·

There are preceding vehicles with taillights on.

·

There are few streetlights along the street ahead.



e.

When the following conditions are met while the adaptive high beam function is operating, headlight swivel control will operate.

·

Vehicle speed is more than approximately 30 km/h (19 mph).

·

The environment is dark and there is no oncoming vehicle with its headlights illuminated and no preceding vehicle with its taillights illuminated.

·

The steering angle is a certain amount or more.


HINT:

The headlight swivel control does not operate when the front wipers are operating in LO or faster.



f.

When the following conditions are met while the adaptive high beam function is operating, the high beam headlights will turn off.

·

Vehicle speed is less than approximately 12 km/h (7 mph).

·

The area in front of the vehicle is light.

·

Multiple vehicles are detected in front of the vehicle.

·

The movement of a vehicle in front is rapid and causing glare.



g.

When the following conditions are met, operation of the adaptive high beam system is canceled and the adaptive high beam indicator in the multi-information display is turned off.

·

Turn the ignition switch off.

·

The light control switch is turned to any position except the AUTO or head position.

·

The low beam headlights are turned off.

·

Move the dimmer switch to the high position.

·

The adaptive high beam switch is off.