Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2021.04–2022.11
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468614 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B124296  Wireless Door Lock Tuner Component Internal Failure  


DESCRIPTION

The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly) via CAN communication system. The certification ECU (smart key ECU assembly) sends door lock/unlock commands to the main body ECU (multiplex network body ECU).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B124296 Wireless Door Lock Tuner Component Internal Failure One of the following conditions is met:
·

Short in RDAM between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in RCO between the certification ECU (smart key ECU assembly) and door control receiver.


·

Door control receiver

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Entry&Start A

WIRING DIAGRAM

B589921E04
4.917,0.938 5.375,1.135 0.458,0.198 10 false I38 4.917,2.219 5.438,2.438 0.521,0.219 10 false I39 5.781,0.427 6.24,0.625 0.458,0.198 10 false 5 V 5.833,1.125 6.292,1.323 0.458,0.198 10 false +B 5.271,0.833 5.729,1.031 0.458,0.198 10 false RCO 5.271,1.51 5.729,1.708 0.458,0.198 10 false RDAM 5.281,2.219 5.74,2.417 0.458,0.198 10 false E 5.229,2.844 6.948,3.448 1.719,0.604 10 false Certification ECU (Smart Key ECU Assembly) 2.156,2.094 2.865,2.302 0.708,0.208 10 false 12*1, 1*2 2.177,1.49 2.906,1.76 0.729,0.271 10 false 2*1, 5*2 2.167,0.813 2.896,1.073 0.729,0.26 10 false 8*1, 4*2 1.906,0.833 2.365,1.031 0.458,0.198 10 false +5 1.698,1.521 2.156,1.719 0.458,0.198 10 false DATA 1.781,2.219 2.24,2.417 0.458,0.198 10 false GND 0.865,1.427 1.323,1.625 0.458,0.198 10 false IC 0.708,2.667 1.896,2.865 1.188,0.198 10 false T11*1, T12*2 0.688,2.813 2.094,3.385 1.406,0.573 10 false Door Control Receiver 4.938,0.729 5.167,0.885 0.229,0.156 10 false 21 4.938,2 5.167,2.156 0.229,0.156 10 false 29 4.927,1.417 5.156,1.573 0.229,0.156 10 false 11 4.927,1.625 5.385,1.823 0.458,0.198 10 false I38 0.271,3.167 2.083,3.448 1.813,0.281 10 false *1: for 12 Pin Type 0.271,3.469 2.083,3.75 1.813,0.281 10 false *2: for 5 Pin Type

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry & Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the certification ECU (smart key ECU assembly) is replaced, refer to Service Bulletin.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and start function and wireless control function performance may be affected.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

This DTC is not stored within 10 seconds of the ignition switch being turned from ON to off.

·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced. (for 12 Pin Type)




PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-Procedure 1

a.

Disconnect the T11*1 or T12*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type



Procedure 1

b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B574616C19
4.667,0.333 5.167,0.583 0.5,0.25 3.333,0.333 3.833,0.583 0.5,0.25 3.698,1.24 3.917,2 3.917,2 4.167,2 true 3.583,1.156 3.25,2 3.25,2 3,2 true 4.604,1.26 4.833,2.25 4.833,2.25 5.083,2.25 true 3.49,0.385 3.948,0.583 0.458,0.198 10 false I38 4.823,0.385 5.281,0.583 0.458,0.198 10 false I39 4.219,1.938 4.677,2.135 0.458,0.198 10 false RCO 2.583,1.927 3.135,2.083 0.552,0.156 10 false RDAM 5.146,2.177 5.698,2.333 0.552,0.156 10 false E 0.26,0.167 0.719,0.365 0.458,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,I39)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I38-11 (RDAM) - I39-29 (E) Always 11 to 14 V
I38-21 (RCO) - I39-29 (E) Always Pulse generation at regular intervals
(Below 1 V ←→ 4.5 to 5.5 V)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I39)Location & Routing

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I39-29 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-Procedure 1

c.

None



OK

REPLACE DOOR CONTROL RECEIVER

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

Pre-Procedure 1

a.

Disconnect the I38 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the T11*1 or T12*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type



Procedure 1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 12 Pin Type:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,T11)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(T11)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assembly

I38-11 (RDAM) - T11-2 (DATA) Always Below 1 Ω
I38-21 (RCO) - T11-8 (+5) Always Below 1 Ω
T11-12 (GND) - Body ground Always Below 1 Ω
T11-2 (DATA) or I38-11 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
T11-8 (+5) or I38-21 (RCO) - Other terminals and body ground Always 10 kΩ or higher

for 5 Pin Type:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,T12)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(T12)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Smart Door Control Receiver Assembly

I38-11 (RDAM) - T12-5 (DATA) Always Below 1 Ω
I38-21 (RCO) - T12-4 (+5) Always Below 1 Ω
T12-1 (GND) - Body ground Always Below 1 Ω
T12-5 (DATA) or I38-11 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
T12-4 (+5) or I38-21 (RCO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-Procedure 1

d.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR