Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM38G0E _59 Vehicle Exterior _100806 WINDOW / GLASS _0467991 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the ignition switch is ON, the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the multiplex network master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor, regulator and ECU functions.

WIRING DIAGRAM

for LHD:


B612389E01
1.625,0.875 2.021,1.073 0.396,0.198 10 false LIN2 2.052,0.729 2.396,0.927 0.344,0.198 10 false 15 2.344,1.5 3.479,1.917 1.135,0.417 10 false Power Distribution Box Assembly 0.615,2.146 2.271,2.615 1.656,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 1.156,3.302 1.948,3.51 0.792,0.208 10 false from Battery 1.146,3.906 1.979,4.125 0.833,0.219 10 false from Battery 2.5,3.51 3.469,3.74 0.969,0.229 10 false ECU-B NO.3 2.646,4.125 3.625,4.365 0.979,0.24 10 false DOOR F/L 4.24,3.229 4.583,3.427 0.344,0.198 10 false 11 4.521,3.219 4.865,3.417 0.344,0.198 10 false B 5.208,3.135 5.552,3.333 0.344,0.198 10 false +B 5.677,3.531 6.167,3.802 0.49,0.271 10 false LIN1 6.104,3.375 6.448,3.573 0.344,0.198 10 false 17 4.677,3.521 5.021,3.719 0.344,0.198 10 false 12 V 4.563,3.854 4.906,4.052 0.344,0.198 10 false 5 V 5.052,4.229 5.5,4.594 0.448,0.365 10 false Control Circuit 4.552,5.313 4.979,5.542 0.427,0.229 10 false LIN2 4.552,5.823 4.896,6.021 0.344,0.198 10 false UP 4.552,6.333 5.073,6.573 0.521,0.24 10 false DOWN 5.656,6.802 6.052,7 0.396,0.198 10 false GND 6.073,6.667 6.417,6.865 0.344,0.198 10 false 12 4.469,7.604 6.052,7.958 1.583,0.354 10 false Multiplex Network Master Switch Assembly 4.25,5.177 4.594,5.375 0.344,0.198 10 false 16 4.26,5.74 4.604,5.938 0.344,0.198 10 false 20 4.24,6.25 4.583,6.448 0.344,0.198 10 false 15 2.635,4.771 2.979,4.969 0.344,0.198 10 false 2 2.625,5.188 2.969,5.385 0.344,0.198 10 false 9 2.594,5.729 2.938,5.927 0.344,0.198 10 false 10 2.625,6.229 2.969,6.427 0.344,0.198 10 false 7 2.604,6.677 2.948,6.875 0.344,0.198 10 false 1 2.167,6.677 2.51,6.875 0.344,0.198 10 false GND 2.031,6.24 2.531,6.448 0.5,0.208 10 false DOWN 2.26,5.729 2.604,5.927 0.344,0.198 10 false UP 2.25,5.198 2.656,5.406 0.406,0.208 10 false LIN 2.365,4.792 2.708,4.99 0.344,0.198 10 false B 1.104,5.896 1.448,6.094 0.344,0.198 10 false IC 1.104,6.198 1.448,6.396 0.344,0.198 10 false IC 0.698,7.594 2.615,7.948 1.917,0.354 10 false Front Power Window Regulator Motor Assembly LH 0.521,8.479 2.156,8.719 1.635,0.24 10 false : LIN Communication Line 4.458,7.417 4.771,7.615 0.313,0.198 10 false N3 0.698,7.406 1.156,7.604 0.458,0.198 10 false N5 0.656,1.969 0.813,2.167 0.156,0.198 10 false A 2.354,1.313 2.667,1.51 0.313,0.198 10 false 5B 3.719,0.729 4.031,0.927 0.313,0.198 10 false 37


for RHD:


B612389E02
1.625,0.875 2.021,1.073 0.396,0.198 10 false LIN2 2.052,0.729 2.396,0.927 0.344,0.198 10 false 15 2.406,1.458 3.552,1.865 1.146,0.406 10 false Power Distribution Box Assembly 0.615,2.146 2.271,2.615 1.656,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 1.188,3.302 1.979,3.521 0.792,0.219 10 false from Battery 1.177,3.906 2,4.115 0.823,0.208 10 false from Battery 2.531,3.51 3.375,3.74 0.844,0.229 10 false ECU-B NO.3 2.604,4.135 3.385,4.365 0.781,0.229 10 false DOOR F/R 4.24,3.229 4.583,3.427 0.344,0.198 10 false 11 4.521,3.219 4.865,3.417 0.344,0.198 10 false B 5.208,3.135 5.552,3.333 0.344,0.198 10 false +B 5.677,3.531 6.167,3.802 0.49,0.271 10 false LIN1 6.104,3.375 6.448,3.573 0.344,0.198 10 false 17 4.677,3.521 5.021,3.719 0.344,0.198 10 false 12 V 4.563,3.854 4.906,4.052 0.344,0.198 10 false 5 V 5.052,4.229 5.5,4.594 0.448,0.365 10 false Control Circuit 4.552,5.313 4.979,5.542 0.427,0.229 10 false LIN2 4.552,5.823 4.896,6.021 0.344,0.198 10 false UP 4.552,6.333 5.073,6.573 0.521,0.24 10 false DOWN 5.656,6.802 6.052,7 0.396,0.198 10 false GND 6.073,6.667 6.417,6.865 0.344,0.198 10 false 12 4.469,7.604 6.052,7.958 1.583,0.354 10 false Multiplex Network Master Switch Assembly 4.25,5.177 4.594,5.375 0.344,0.198 10 false 16 4.26,5.74 4.604,5.938 0.344,0.198 10 false 20 4.24,6.25 4.583,6.448 0.344,0.198 10 false 15 2.635,4.771 2.979,4.969 0.344,0.198 10 false 2 2.625,5.188 2.969,5.385 0.344,0.198 10 false 9 2.594,5.729 2.938,5.927 0.344,0.198 10 false 10 2.625,6.229 2.969,6.427 0.344,0.198 10 false 7 2.604,6.677 2.948,6.875 0.344,0.198 10 false 1 2.167,6.677 2.51,6.875 0.344,0.198 10 false GND 2.031,6.24 2.531,6.448 0.5,0.208 10 false DOWN 2.26,5.729 2.604,5.927 0.344,0.198 10 false UP 2.25,5.198 2.656,5.406 0.406,0.208 10 false LIN 2.365,4.792 2.708,4.99 0.344,0.198 10 false B 1.104,5.896 1.448,6.094 0.344,0.198 10 false IC 1.104,6.198 1.448,6.396 0.344,0.198 10 false IC 0.698,7.594 2.615,7.948 1.917,0.354 10 false Front Power Window Regulator Motor Assembly RH 0.521,8.479 2.156,8.719 1.635,0.24 10 false : LIN Communication Line 4.458,7.417 4.771,7.615 0.313,0.198 10 false M4 0.698,7.406 1.156,7.604 0.458,0.198 10 false M6 0.656,1.969 0.813,2.167 0.156,0.198 10 false A 2.417,1.281 2.729,1.479 0.313,0.198 10 false 5B 3.719,0.719 4.031,0.917 0.313,0.198 10 false 37


CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated
-
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

C

2.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
2.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.
B527907C26
1.073,0.156 1.5,0.396 0.427,0.24 1.865,0.156 2.292,0.396 0.427,0.24 0.813,0.771 1.51,1.104 true 0.792,1.813 1.469,1.531 true 2.688,1.823 1.99,1.563 true 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 1.198,0.198 1.531,0.458 0.333,0.26 10 false N5 0.438,0.677 0.896,0.875 0.458,0.198 10 false GND 0.302,1.76 0.823,1.979 0.521,0.219 10 false DOWN 2.781,1.76 3.042,1.979 0.26,0.219 10 false UP 1.573,0.198 1.885,0.396 0.313,0.198 10 false *A 1.99,0.198 2.448,0.396 0.458,0.198 10 false M6 2.375,0.198 2.688,0.396 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly)


Disconnect the N5*1 or M6*2 front power window regulator motor assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(N5)Location & Routing

Click Connector(N5)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

N5-10 (UP) - N5-1 (GND)
·

Ignition switch ON

·

Multiplex network master switch assembly (driver side switch) OFF → UP (manual operation)


11 to 14 V → Below 1 V
N5-7 (DOWN) - N5-1 (GND)
·

Ignition switch ON

·

Multiplex network master switch assembly (driver side switch) OFF → DOWN (manual operation)


11 to 14 V → Below 1 V


for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(M6)Location & Routing

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

M6-10 (UP) - M6-1 (GND)
·

Ignition switch ON

·

Multiplex network master switch assembly (driver side switch) OFF → UP (manual operation)


11 to 14 V → Below 1 V
M6-7 (DOWN) - M6-1 (GND)
·

Ignition switch ON

·

Multiplex network master switch assembly (driver side switch) OFF → DOWN (manual operation)


11 to 14 V → Below 1 V


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

C

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY)

*1: for LHD

*2: for RHD


a.

Disconnect the N3*1 or M4*2 multiplex network master switch assembly connector.


b.

Disconnect the N5*1 or M6*2 front power window regulator motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(N3,N5)Location & Routing

Click Connector(N3)Body>Front Door Wire LH>Multiplex Network Master Switch Assembly

Click Connector(N5)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

N3-20 (UP) - N5-10 (UP) Always Below 1 Ω
N3-15 (DOWN) - N5-7 (DOWN) Always Below 1 Ω
N3-20 (UP) or N5-10 (UP) - Body ground Always 10 kΩ or higher
N3-15 (DOWN) or N5-7 (DOWN) - Body ground Always 10 kΩ or higher


for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(M4,M6)Location & Routing

Click Connector(M4)Body>Front Door Wire RH>Multiplex Network Master Switch Assembly

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

M4-20 (UP) - M6-10 (UP) Always Below 1 Ω
M4-15 (DOWN) - M6-7 (DOWN) Always Below 1 Ω
M4-20 (UP) or M6-10 (UP) - Body ground Always 10 kΩ or higher
M4-15 (DOWN) or M6-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR