Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM38G0E _58 Vehicle Interior _100749 LIGHTING (INT) _0468730 LIGHTING SYSTEM D

LIGHTING (INT)  LIGHTING SYSTEM  OPERATION CHECK  


INSPECT ILLUMINATED ENTRY SYSTEM OPERATION


NOTICE:

Perform this inspection with the customize parameters at the initial settings.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS


HINT:

Perform this inspection with the door switch of the map light assembly and spot light assembly on.

Lights Controlled by Illuminated Entry System
Control Condition Lights that Operate

*1: w/ Map Light

*2: for Spot Light Type

*3: for Dome Light Type

*4: w/ Front Footwell Light

*5: w/ Rear Footwell Light

Actuation Area-linked With the ignition switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off.
·

Map light assembly*1

·

Spot light assembly*2

·

No. 1 room light assembly*3

·

No. 2 room light assembly

·

No. 1 interior illumination light assembly (driver side footwell light)*4

·

No. 1 interior illumination light assembly (front passenger side footwell light)*4

·

No. 1 interior illumination light assembly LH (rear left side footwell light)*5

·

No. 1 interior illumination light assembly RH (rear right side footwell light)*5

·

Front door inside handle illumination light assembly LH*4

·

Front door inside handle illumination light assembly RH*4

·

Rear door inside handle illumination light assembly LH*4

·

Rear door inside handle illumination light assembly RH*4


Door Lock/Unlock-linked With the ignition switch off and all of the doors closed and locked, unlock either front door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off.
·

Map light assembly*1

·

Spot light assembly*2

·

No. 1 room light assembly*3

·

No. 2 room light assembly

·

No. 1 interior illumination light assembly (driver side footwell light)*4

·

No. 1 interior illumination light assembly (front passenger side footwell light)*4

·

No. 1 interior illumination light assembly LH (rear left side footwell light)*5

·

No. 1 interior illumination light assembly RH (rear right side footwell light)*5

·

Front door inside handle illumination light assembly LH*4

·

Front door inside handle illumination light assembly RH*4

·

Rear door inside handle illumination light assembly LH*4

·

Rear door inside handle illumination light assembly RH*4


Door Open/Close-linked With the ignition switch off and all of the doors closed, open either front door and check that the lights that operate turn ON. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.
·

Map light assembly*1

·

Spot light assembly*2

·

No. 1 room light assembly*3

·

No. 2 room light assembly

·

No. 1 interior illumination light assembly (driver side footwell light)*4

·

No. 1 interior illumination light assembly (front passenger side footwell light)*4

·

No. 1 interior illumination light assembly LH (rear left side footwell light)*5

·

No. 1 interior illumination light assembly RH (rear right side footwell light)*5

·

Front door inside handle illumination light assembly LH*4

·

Front door inside handle illumination light assembly RH*4

·

Rear door inside handle illumination light assembly LH*4

·

Rear door inside handle illumination light assembly RH*4


With the ignition switch off and all the doors closed, open the front door and check that the blinking interval for the lights listed on the right slows down. After this, check that the blinking interval for the lights listed on the right quickens when the brake pedal is depressed. Engine switch illumination
With the ignition switch ON, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off.
·

Map light assembly*1

·

Spot light assembly*2

·

No. 1 room light assembly*3

·

No. 2 room light assembly


Engine Switch-linked Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.
·

Map light assembly*1

·

Spot light assembly*2

·

No. 1 room light assembly*3

·

No. 2 room light assembly

·

No. 1 interior illumination light assembly (driver side footwell light)*4

·

No. 1 interior illumination light assembly (front passenger side footwell light)*4

·

No. 1 interior illumination light assembly LH (rear left side footwell light)*5

·

No. 1 interior illumination light assembly RH (rear right side footwell light)*5

·

Front door inside handle illumination light assembly LH*4

·

Front door inside handle illumination light assembly RH*4

·

Rear door inside handle illumination light assembly LH*4

·

Rear door inside handle illumination light assembly RH*4


Turn the ignition switch ACC or ON and check that the lights that operate turn on.
·

Map light assembly*1

·

Spot light assembly*2

·

No. 1 room light assembly*3

·

No. 2 room light assembly

·

No. 1 interior illumination light assembly (driver side footwell light)*4

·

No. 1 interior illumination light assembly (front passenger side footwell light)*4

·

No. 1 interior illumination light assembly LH (rear left side footwell light)*5

·

No. 1 interior illumination light assembly RH (rear right side footwell light)*5

·

Front door inside handle illumination light assembly LH*4

·

Front door inside handle illumination light assembly RH*4

·

Rear door inside handle illumination light assembly LH*4

·

Rear door inside handle illumination light assembly RH*4


Check that the blinking interval for the lights listed on the right slows down when the ignition switch is turned from ACC or ON to off. Engine switch illumination
Vehicle Speed-linked With the ignition switch turned to ACC or ON, release the parking brake, drive the vehicle at least 3 km/h (1.9 mph), and check that the lights dim. While the lights are dim, stop the vehicle, apply the parking brake, and check that the lights return to full brightness.
·

No. 1 interior illumination light assembly (driver side footwell light)*4

·

No. 1 interior illumination light assembly (front passenger side footwell light)*4

·

No. 1 interior illumination light assembly LH (rear left side footwell light)*5

·

No. 1 interior illumination light assembly RH (rear right side footwell light)*5

·

Front door inside handle illumination light assembly LH*4

·

Front door inside handle illumination light assembly RH*4

·

Rear door inside handle illumination light assembly LH*4

·

Rear door inside handle illumination light assembly RH*4





INSPECT BATTERY SAVING CONTROL OPERATION


a.

The operations and conditions of this control are described below.

Control Condition Lights that Operate

*1: w/ Map Light

*2: for Spot Light Type

*3: for Dome Light Type

*4: w/ Front Footwell Light

*5: w/ Rear Footwell Light

*6: w/ Vanity Light

*7: w/ Scuff Light

*8: w/ Courtesy Light

Basic operation When 20 minutes elapse after the ignition switch is turned from ACC or IG to off and the lights that operate remain on, the lights are turned off.
HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

·

The ignition switch is turned to ACC or IG.

·

Any door is opened and closed.

·

The back door is opened and closed.

·

Any door is unlocked.

·

The key enters any exterior actuation area.



·

Engine switch illumination

·

Map light assembly*1

·

Spot light assembly*2

·

No. 1 room light assembly*3

·

No. 2 room light assembly

·

No. 1 interior illumination light assembly (glove box light assembly)

·

No. 1 interior illumination light assembly (driver side footwell light)*4

·

No. 1 interior illumination light assembly (front passenger side footwell light)*4

·

No. 1 interior illumination light assembly LH (rear left side footwell light)*5

·

No. 1 interior illumination light assembly RH (rear right side footwell light)*5

·

Front door inside handle illumination light assembly LH*4

·

Front door inside handle illumination light assembly RH*4

·

Rear door inside handle illumination light assembly LH*4

·

Rear door inside handle illumination light assembly RH*4

·

Vanity light assembly*6

·

Scuff light LH (front door scuff plate LH)*7

·

Scuff light RH (front door scuff plate RH)*7

·

Courtesy light assembly*8


Interior light auto cut operation When 20 minutes elapse after the ignition switch is turned from on (ACC or IG) to off and the lights that operate remain on, the lights are turned off.
HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

·

The ignition switch is turned to ACC or IG.



·

Map light assembly*1

·

Spot light assembly*2

·

No. 1 room light assembly*3

·

No. 2 room light assembly

·

Vanity light assembly*6