Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM38G0E _52 Drivetrain _100436 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0468743 AUTOMATIC TRANSMISSION SYSTEM U

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List.


g.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
550 to 700 rpm: Idling (shift lever in N, engine warmed up and A/C off) -
Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F)
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.
Battery Voltage Battery voltage Min.: 0 V
Max.: 65.535 V
11 to 14 V: Ignition switch ON -
Accelerator Position Accelerator pedal position Min.: 0%
Max.: 399.9%
Actual accelerator pedal position -
N Range Status Shift lever N status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


-
Neutral Position SW Park/neutral position switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


Transfer L4 Transfer status ON or OFF
·

ON: Transfer in L4

·

OFF: Transfer not in L4


-
Stop Light SW Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
NT Sensor Speed Input turbine speed Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed

·

Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed


Data is displayed in increments of 50 rpm.
Speed (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped (equal to vehicle speed) -
SP2 Sensor Voltage Transmission revolution sensor (SP2) sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling -
Shift SW Status (P Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


Shift SW Status (R Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


Shift SW Status (N Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


Shift SW Status (N,P Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


-
Shift SW Status (N,P Range) Supported Status of park/neutral position switch (N or P) supported Supp or Unsupp - -
Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sport Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Shift SW Status (S Range) Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Snow Mode SW 2ND switch status ON or OFF
·

ON: 2ND switch pushed

·

OFF: 2ND switch not pushed


-
Shift SW Status (D Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in D, S, "+" or "-"

·

OFF: Shift lever not in D, S, "+" or "-"


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


A/T Oil Temperature No.1 No. 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approx. 80°C (176°F): After stall test

·

Equal to ambient temperature when cold soak


If the value -40°C (-40°F) or 150°C (302°F), No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature No.2 No. 2 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approx. 80°C (176°F): After stall test

·

Equal to ambient temperature when cold soak


If the value -40°C (-40°F) or 150°C (302°F), No. 2 ATF temperature sensor circuit is open or shorted.
ATF Thermal Degradation Estimate Estimated value of ATF thermal degradation Min.: 0
Max.: 65535
- If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected.
Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.
Torque Converter Temperature Raise History Torque converter temperature raise history status Min.: 0
Max.: 255
- -
NT Sensor Voltage Transmission revolution sensor (NT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling -
Drive Mode Status Drive mode status Normal or Power - -
Endless Rotary Switch (Phase A) MODE SELECT switch status ON or OFF Repeatedly switched ON → OFF → OFF → ON: MODE SELECT switch turned to the right -
Endless Rotary Switch (Phase B) MODE SELECT switch status ON or OFF Repeatedly switched ON → ON → OFF → OFF: MODE SELECT switch turned to the right -
Power Mode SW PWR switch status ON or OFF
·

ON: PWR switch pushed

·

OFF: PWR switch not pushed


-
Lock Up Status Lock up status ON or OFF
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
Shift Status ECM gear shift command 1st, 2nd, 3rd, 4th, 5th or 6th Same as actual gear -
Solenoid (SLT) Shift solenoid valve SLT status ON or OFF
·

ON: Shift solenoid valve SLT operating

·

OFF: Shift solenoid valve SLT not operating


-
Solenoid (SLU) Shift solenoid valve SLU status ON or OFF
·

ON: Lock-up permitted

·

OFF: Lock-up not permitted


-
Solenoid (SL1) Shift solenoid valve SL1 status ON or OFF
·

ON: Shift solenoid valve SL1 operating

·

OFF: Shift solenoid valve SL1 not operating


The value of this item only changes when performing an Active Test.
Solenoid (SL2) Shift solenoid valve SL2 status ON or OFF
·

ON: Shift solenoid valve SL2 operating

·

OFF: Shift solenoid valve SL2 not operating


The value of this item only changes when performing an Active Test.
Solenoid (SL3) Shift solenoid valve SL3 status ON or OFF
·

ON: Shift solenoid valve SL3 operating

·

OFF: Shift solenoid valve SL3 not operating


The value of this item only changes when performing an Active Test.
Solenoid (SL4) Shift solenoid valve SL4 status ON or OFF
·

ON: Shift solenoid valve SL4 operating

·

OFF: Shift solenoid valve SL4 not operating


The value of this item only changes when performing an Active Test.
Solenoid (SL) Shift solenoid valve SL status ON or OFF
·

ON: Lock-up permitted

·

OFF: Lock-up not permitted


-
Snow or 2nd Start Mode Status 2nd start mode status ON or OFF
·

ON: 2ND start mode on

·

OFF: 2ND start mode off


-
HINT:

*: Refer to DTC P070513 or P070562.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>P070513




ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test.


g.

Perform the Active Test according to the display on the GTS.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the TC Terminal Changes to the fluid temperature detection mode ON/OFF
[Vehicle Condition]
·

Ignition switch ON

·

Vehicle stopped


Control the Shift Position Operates the shift solenoid valves to allow gears to be selected manually. 1st/2nd/3rd/4th/5th/6th
Start/Stop
Can be used to check the operation of the shift solenoid valves.
Up-shifts and down-shifts should be performed consecutively. A 10 second interval is required between gear changes.
Do not down-shift at high speeds. Doing so will damage the automatic transmission.
[Vehicle Condition]

50 km/h (31 mph) or less


Activate the Solenoid (SLU) Operates shift solenoid valve SLU ON/OFF
[Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the ignition switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SLT) Operates shift solenoid valve SLT to raise the line pressure. ON/OFF
HINT:

ON: No action (normal operation)

OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the shift solenoid valve SLT to turn off).


[Vehicle Condition]
·

Vehicle stopped

·

Engine idling


Activate the Lock Up Solenoid Controls the shift solenoid valves SLU and SL to set the automatic transmission to the lock-up condition. ON/OFF
Start/Stop
Can be used to check shift solenoid valves SLU and SL operation.
[Vehicle Condition]
·

Vehicle speed: 70 km/h (44 mph) or more

·

Gear: Highest gear

·

Throttle valve opening angle: Less than 20%


Activate the Solenoid (SL) Operates shift solenoid valve SL ON/OFF
[Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the ignition switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SL1) Operates shift solenoid valve SL1 ON/OFF
[Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the ignition switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SL2) Operates shift solenoid valve SL2 ON/OFF
[Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the ignition switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SL3) Operates shift solenoid valve SL3 ON/OFF
[Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the ignition switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SL4) Operates shift solenoid valve SL4 ON/OFF
[Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the ignition switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


The "Activate the Solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>HYDRAULIC TEST

HINT:

Note that the pressure readings for the Active Test and Hydraulic Test are different.