Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467497 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display)  B158F  AV Signal Stoppage (Low Battery Voltage)  


DESCRIPTION

This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B158F AV Signal Stoppage (Low Battery Voltage) A video or audio signal is interrupted when the battery voltage drops
·

Radio and display receiver assembly

·

Harness or connector


Navigation System A

WIRING DIAGRAM

E468502E01
4.917,1.865 5.375,2.063 0.458,0.198 10 false I11 4.906,2.042 6.604,2.479 1.698,0.438 10 false Radio and Display Receiver Assembly 5.271,1.021 5.729,1.219 0.458,0.198 10 false +B1 5.073,0.927 5.531,1.125 0.458,0.198 10 false 4 3.313,1.208 4.24,1.542 0.927,0.333 10 false RADIO 0.781,1.031 1.75,1.229 0.969,0.198 10 false from Battery*2 1.979,0.313 3.313,0.667 1.333,0.354 10 false from Engine Stop and Start ECU*1 0.135,2.052 2.115,2.25 1.979,0.198 10 false *1: w/ Stop and Start System 0.146,2.375 2.125,2.563 1.979,0.188 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)

Pre-procedure1

a.
E268487

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>OPERATION CHECK


Procedure1

b.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:

This display is updated once per second.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

2.CHECK DTC

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
2.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>DTC CHECK / CLEAR


Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

b.

Recheck for DTCs and check that no DTCs are output.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>DTC CHECK / CLEAR


Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


Post-procedure1

c.

None



A

B

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the I11 radio and display receiver assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I11)Location & Routing

Click Connector(I11)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I11-4 (+B1) - Body ground Aiways 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR