Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467497 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display)  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the rear television camera assembly and the radio and display receiver assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly


Navigation System A

WIRING DIAGRAM

E402604E38
1.583,2.979 4.375,3.198 2.792,0.219 10 false Radio and Display Receiver Assembly 1.583,2.813 1.969,3.01 0.385,0.198 10 false I13 2.135,2.5 2.74,2.74 0.604,0.24 10 false CSLD 2.083,2.083 2.635,2.292 0.552,0.208 10 false CGND 2.344,1.646 2.729,1.844 0.385,0.198 10 false V- 2.313,1.25 2.698,1.448 0.385,0.198 10 false V+ 2.229,0.823 2.615,1.021 0.385,0.198 10 false CA+ 2.615,0.719 3,0.917 0.385,0.198 10 false 30 2.604,1.563 2.99,1.76 0.385,0.198 10 false 29 2.604,1.135 2.99,1.333 0.385,0.198 10 false 28 2.615,1.979 3,2.177 0.385,0.198 10 false 27 2.604,2.406 2.99,2.604 0.385,0.198 10 false 26 5,2.813 6.167,3.01 1.167,0.198 10 false g9*2, g10*3 5.01,3.01 7.156,3.292 2.146,0.281 10 false Rear Television Camera Assembly 5.531,0.833 5.917,1.031 0.385,0.198 10 false CB+ 5.521,1.271 5.906,1.469 0.385,0.198 10 false CV+ 5.51,1.688 5.896,1.885 0.385,0.198 10 false CV- 5.51,2.104 6.104,2.375 0.594,0.271 10 false CGND 5.292,0.75 5.677,0.948 0.385,0.198 10 false 6 5.292,1.146 5.677,1.344 0.385,0.198 10 false 3 5.281,1.552 5.667,1.75 0.385,0.198 10 false 2 5.281,1.979 5.667,2.177 0.385,0.198 10 false 5 3.896,2.396 4.281,2.594 0.385,0.198 10 false *1 0.26,3.438 1.104,3.646 0.844,0.208 10 false *1: Shielded 1.469,3.448 3.979,3.646 2.51,0.198 10 false *2: w/ Parking Assist Monitor System 4.313,3.448 6.771,3.625 2.458,0.177 10 false *3: w/ Rear View Monitor System

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point". (w/ Parking Assist Monitor System)

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed. (w/ Parking Assist Monitor System)

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

Pre-procedure1

a.

Disconnect the g9*1 or g10*2 rear television camera assembly connector.

*1: w/ Parking Assist Monitor System

*2: w/ Rear View Monitor System


b.

Disconnect the I13 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Parking Assist Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(g9,I13)Location & Routing

Click Connector(g9)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

g9-6 (CB+) - I13-30 (CA+) Always Below 1 Ω
g9-3 (CV+) - I13-28 (V+) Always Below 1 Ω
g9-2 (CV-) - I13-29 (V-) Always Below 1 Ω
g9-5 (CGND) - I13-27 (CGND) Always Below 1 Ω
g9-6 (CB+) - Body ground Always 10 kΩ or higher
g9-3 (CV+) - Body ground Always 10 kΩ or higher
g9-2 (CV-) - Body ground Always 10 kΩ or higher
g9-5 (CGND) - Body ground Always 10 kΩ or higher

w/ Rear View Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(g10,I13)Location & Routing

Click Connector(g10)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

g10-6 (CB+) - I13-30 (CA+) Always Below 1 Ω
g10-3 (CV+) - I13-28 (V+) Always Below 1 Ω
g10-2 (CV-) - I13-29 (V-) Always Below 1 Ω
g10-5 (CGND) - I13-27 (CGND) Always Below 1 Ω
g10-6 (CB+) - Body ground Always 10 kΩ or higher
g10-3 (CV+) - Body ground Always 10 kΩ or higher
g10-2 (CV-) - Body ground Always 10 kΩ or higher
g10-5 (CGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK RADIO AND DISPLAY ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY ASSEMBLY (CA+, CGND)

Pre-procedure1

a.
E402607C46
1.583,0.156 1.969,0.458 0.385,0.302 0.583,1.646 0.771,1.646 0.771,1.646 0.969,1.24 true 0.969,1.844 1.156,1.844 1.156,1.844 1.417,1.25 true 1.698,0.229 2.156,0.427 0.458,0.198 10 false I13 0.24,0.135 0.698,0.333 0.458,0.198 10 false *a 0.25,1.542 0.708,1.74 0.458,0.198 10 false CA+ 0.542,1.75 1.052,1.948 0.51,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector still connected.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL



Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-30 (CA+) - I13-27 (CGND) Ignition switch ACC 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-27 (CGND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

3.CHECK REAR TELEVISION CAMERA ASSEMBLY

Pre-procedure1

E402606C41
0.958,1.073 1.313,1.344 0.354,0.271 2.698,2.885 2.875,2.885 2.875,2.885 3.135,2.25 true 5,2.792 5.177,2.792 5.177,2.792 5.438,2.156 true 3.208,2.167 3.375,2.917 3.375,2.917 3.531,2.917 true 5.542,2.104 5.708,2.854 5.708,2.854 5.865,2.854 true 0.344,2.573 0.521,2.573 0.521,2.573 0.635,1.969 true 0.74,1.958 0.865,2.823 0.865,2.823 1.021,2.823 true 0.177,0.99 0.49,1.188 0.313,0.198 10 false *a 2.635,0.979 2.948,1.177 0.313,0.198 10 false *b 4.948,0.927 5.26,1.125 0.313,0.198 10 false *c 2.531,2.792 2.844,2.99 0.313,0.198 10 false *d 3.583,2.813 3.896,3.01 0.313,0.198 10 false *e 4.823,2.698 5.135,2.896 0.313,0.198 10 false *d 5.917,2.76 6.229,2.958 0.313,0.198 10 false *e 2.448,1.792 2.906,2.031 0.458,0.24 10 false GND 4.75,1.813 5.208,2.052 0.458,0.24 10 false GND 1.073,2.75 1.385,2.948 0.313,0.198 10 false V+ 0.135,2.479 0.448,2.677 0.313,0.198 10 false V- 1.063,1.125 1.375,1.323 0.313,0.198 10 false I13
*a Component with harness connected *b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -


a.

Remove the radio and display receiver assembly with the connector still connected.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL



Procedure1

b.

Check the waveform of the rear television camera assembly using an oscilloscope.

Item Content
Measurement terminal I13-28 (V+) - I13-29 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift position in R, camera lens is not covered, displaying an image.
Waveform 2: Ignition switch ON, shift position in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition is ACC.



OK:

Waveform is as shown in the illustration.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG