Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467497 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnostic procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E464148E03
1.031,0.635 1.646,0.833 0.615,0.198 10 false UDO+ 1.031,1.063 1.646,1.26 0.615,0.198 10 false UDO- 1.01,1.469 1.625,1.667 0.615,0.198 10 false UJSG 1.135,1.885 1.521,2.094 0.385,0.208 10 false UPI 1.042,2.365 1.656,2.563 0.615,0.198 10 false UJSS 5.896,0.646 6.51,0.844 0.615,0.198 10 false US1+ 5.906,1.073 6.521,1.271 0.615,0.198 10 false US1- 5.896,1.49 6.51,1.688 0.615,0.198 10 false UGD1 5.906,1.885 6.521,2.083 0.615,0.198 10 false USV1 5.896,2.354 6.51,2.552 0.615,0.198 10 false USG1 2.563,3.448 5.385,3.625 2.823,0.177 10 false : Data Signal (USB Communication Line) 0.302,3.083 1.583,3.552 1.281,0.469 10 false No. 1 Stereo Jack Adapter Assembly 5.76,3.094 6.979,3.542 1.219,0.448 10 false Radio and Display Receiver Assembly 0.313,2.896 1.563,3.094 1.25,0.198 10 false I162 1.542,0.49 2.344,0.688 0.802,0.198 10 false 10 1.573,0.938 2.344,1.146 0.771,0.208 10 false 9 1.542,1.354 2.292,1.542 0.75,0.188 10 false 11 1.563,1.76 2.177,1.958 0.615,0.198 10 false 8 1.531,2.24 2.25,2.427 0.719,0.188 10 false 12 5.781,2.917 7.135,3.135 1.354,0.219 10 false I173 5.625,0.51 5.844,0.708 0.219,0.198 10 false 3 5.625,0.917 5.844,1.115 0.219,0.198 10 false 2 5.635,1.344 5.854,1.542 0.219,0.198 10 false 4 5.635,1.76 5.854,1.958 0.219,0.198 10 false 1 5.625,2.229 5.844,2.427 0.219,0.198 10 false 5 3.542,2.365 4.792,2.563 1.25,0.198 10 false * 2.51,3.146 3.76,3.344 1.25,0.198 10 false *: Shielded 2.844,2.625 5.313,2.823 2.469,0.198 10 false No. 1 Navigation Wire

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>PRECAUTION


HINT:
·

When a large amount of data is in a USB device, it may take a while to begin playback.

·

When using a USB device, files that are protected by copyright cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

(a)

Add numbers in front of the file names.

(b)

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>SYSTEM DESCRIPTION


Result:
Result Proceed to
No playable files exist, or incompatible device format or version. A
Playable files exist, and compatible device format or version. B




A

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION IS INCOMPATIBLE, OR NO PLAYABLE FILES EXIST)

B

2.CHECK NO. 1 NAVIGATION WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK NO. 1 NAVIGATION WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the I173 radio and display receiver assembly connector.


b.

Disconnect the I162 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I173,I162)Location & Routing

Click Connector(I173)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

Click Connector(I162)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Stereo Jack Adapter Assembly

I173-1 (USV1) - I162-8 (UPI) Always Below 1 Ω
I173-2 (US1-) - I162-9 (UDO-) Always Below 1 Ω
I173-3 (US1+) - I162-10 (UDO+) Always Below 1 Ω
I173-4 (UGD1) - I162-11 (UJSG) Always Below 1 Ω
I173-5 (USG1) - I162-[12] (UJSS) Always Below 1 Ω
I173-1 (USV1) - Body ground Always 10 kΩ or higher
I173-2 (US1-) - Body ground Always 10 kΩ or higher
I173-3 (US1+) - Body ground Always 10 kΩ or higher
I173-4 (UGD1) - Body ground Always 10 kΩ or higher
I173-5 (USG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPLACE NO. 1 NAVIGATION WIRE

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Disconnect the I162 No. 1 stereo jack adapter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I162)Location & Routing

Click Connector(I162)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Stereo Jack Adapter Assembly

I162-8 (UPI) - I162-11 (UJSG) Ignition switch ACC 5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that a backup of the music data is available before performing this operation.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn the ignition switch off to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.




Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the radio and display receiver assembly, and if information such as track, artist and album names is displayed on the screen.

OK:

USB device or "iPod" is recognized properly and the information is displayed on the screen.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG