Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467497 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display)  Sound Signal Circuit between Radio Receiver and Stereo Component Equalizer  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component equalizer assembly via this circuit.

The sound signal that is sent is amplified by the stereo component equalizer assembly, and then is sent to the speakers.

If there is an open or short in this circuit, sound cannot be heard from the speakers even if the stereo component equalizer assembly or speakers are not malfunctioning.

WIRING DIAGRAM

E402621E37
5.583,2.396 6.74,2.854 1.156,0.458 10 false S25 1.229,1.542 2.385,2 1.156,0.458 10 false FL- 1.188,1.125 2.344,1.583 1.156,0.458 10 false FL+ 1.208,0.698 2.365,1.156 1.156,0.458 10 false FR- 1.188,0.292 2.344,0.75 1.156,0.458 10 false FR+ 1.583,0.198 2.74,0.656 1.156,0.458 10 false 1 1.594,0.604 2.75,1.063 1.156,0.458 10 false 6 1.594,1.01 2.75,1.469 1.156,0.458 10 false 2 1.594,1.438 2.75,1.896 1.156,0.458 10 false 7 3.563,1.865 4.719,2.323 1.156,0.458 10 false * 0.458,2.406 1.615,2.865 1.156,0.458 10 false I16 0.458,2.563 1.677,2.99 1.219,0.427 10 false Radio and Display Receiver Assembly 5.656,2.031 6.813,2.49 1.156,0.458 10 false ASGI 5.688,1.542 6.844,2 1.156,0.458 10 false FLI- 5.677,1.135 6.833,1.594 1.156,0.458 10 false FLI+ 5.667,0.292 6.823,0.75 1.156,0.458 10 false FRI+ 5.677,0.698 6.833,1.156 1.156,0.458 10 false FRI- 5.438,1.896 5.833,2.292 0.396,0.396 10 false 7 5.375,1.438 5.771,1.833 0.396,0.396 10 false 24 5.427,1.021 5.823,1.417 0.396,0.396 10 false 9 5.438,0.177 5.833,0.573 0.396,0.396 10 false 8 5.375,0.594 5.771,0.99 0.396,0.396 10 false 23 0.333,3.313 1.49,3.552 1.156,0.24 10 false *: Shielded 5.573,2.552 6.792,2.979 1.219,0.427 10 false Stereo Component Equalizer Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT EQUALIZER ASSEMBLY)
a.

Disconnect the I16 radio and display receiver assembly connector.


b.

Disconnect the S25 stereo component equalizer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S25,I16)Location & Routing

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

Click Connector(I16)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

S25-8 (FRI+) - I16-1 (FR+) Always Below 1 Ω
S25-23 (FRI-) - I16-6 (FR-) Always Below 1 Ω
S25-9 (FLI+) - I16-2 (FL+) Always Below 1 Ω
S25-24 (FLI-) - I16-7 (FL-) Always Below 1 Ω
S25-7 (ASGI) - Body ground Always 10 kΩ or higher
S25-8 (FRI+) - Body ground Always 10 kΩ or higher
S25-23 (FRI-) - Body ground Always 10 kΩ or higher
S25-9 (FLI+) - Body ground Always 10 kΩ or higher
S25-24 (FLI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR