Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467497 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E466180E02
2.177,0.885 3.208,1.125 1.031,0.24 10 false from Battery*2 1.958,1.896 3.26,2.146 1.302,0.25 10 false from ACC Relay*2 1.646,2.906 3.344,3.177 1.698,0.271 10 false from IGR-NO.2 Relay*2 4.115,1.063 5.063,1.323 0.948,0.26 10 false RADIO 3.969,2.042 5.042,2.24 1.073,0.198 10 false ECU-ACC 3.917,3.052 5.906,3.25 1.99,0.198 10 false ECU-IGR NO.2 5.479,0.896 5.792,1.094 0.313,0.198 10 false I11 5.469,2.875 5.781,3.073 0.313,0.198 10 false I13 5.51,0.688 5.667,0.885 0.156,0.198 10 false 4 5.49,1.667 5.802,1.865 0.313,0.198 10 false 15 5.479,2.667 5.792,2.865 0.313,0.198 10 false 19 5.531,3.458 5.688,3.656 0.156,0.198 10 false 1 5.792,0.865 6.125,1.042 0.333,0.177 10 false +B1 5.792,1.875 6.24,2.052 0.448,0.177 10 false ACC1 5.823,2.875 6.031,3.052 0.208,0.177 10 false IG 5.823,3.667 6.229,3.854 0.406,0.188 10 false GND1 5.229,4.125 6.927,4.521 1.698,0.396 10 false Radio and Display Receiver Assembly 5.469,3.667 5.781,3.865 0.313,0.198 10 false I11 0.948,0.354 5.844,0.552 4.896,0.198 10 false from Engine Stop and Start ECU*1 0.938,1.354 5.833,1.552 4.896,0.198 10 false from Engine Stop and Start ECU*1 0.948,2.344 5.844,2.542 4.896,0.198 10 false from Engine Stop and Start ECU*1 5.469,1.885 5.781,2.083 0.313,0.198 10 false I11 0.167,4.385 4.448,4.583 4.281,0.198 10 false *2: w/o Stop and Start System 0.156,4.021 4.438,4.219 4.281,0.198 10 false *1: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the I11 and I13 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I11)Location & Routing

Click Connector(I11)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I11-1 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I11,I13)Location & Routing

Click Connector(I11)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I11-4 (+B1) - I11-1 (GND1) Always 10.5 to 16 V*1
11 to 14 V*2
I11-15 (ACC1) - I11-1 (GND1) Ignition switch ACC 10.5 to 16 V*1
11 to 14 V*2
I13-19 (IG) - I11-1 (GND1) Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR