Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467495 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio receiver assembly.

WIRING DIAGRAM

E402685E03
1.844,0.688 3.396,1.052 1.552,0.365 10 false from Battery*2 3.688,0.844 4.167,1.083 0.479,0.24 10 false RADIO 3.625,1.938 4.583,2.219 0.958,0.281 10 false ECU-ACC 1.656,1.75 3.167,2 1.51,0.25 10 false from ACC Relay*2 5.396,3.281 7.083,3.688 1.688,0.406 10 false Radio Receiver Assembly 5.396,3.094 5.719,3.292 0.323,0.198 10 false I8 5.677,0.708 6.156,0.948 0.479,0.24 10 false +B1 5.677,2.458 6.156,2.698 0.479,0.24 10 false GND1 5.688,1.74 6.167,1.979 0.479,0.24 10 false ACC1 5.427,0.594 5.563,0.802 0.135,0.208 10 false 4 5.417,1.625 5.552,1.833 0.135,0.208 10 false 3 5.438,2.333 5.573,2.542 0.135,0.208 10 false 7 0.688,0.281 2.885,0.552 2.198,0.271 10 false from Engine Stop and Start ECU*1 0.677,1.375 2.844,1.604 2.167,0.229 10 false from Engine Stop and Start ECU*1 0.125,2.667 2.292,2.896 2.167,0.229 10 false *1: w/ Stop and Start System 0.135,3.042 2.302,3.271 2.167,0.229 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the I8 radio receiver assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

Click Location & Routing(I8)Location & Routing

Click Connector(I8)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I8-4 (+B1) - Body ground Always 11 to 14 V*1
10.5 to 16 V*2
I8-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V*1
10.5 to 16 V*2



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I8)Location & Routing

Click Connector(I8)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I8-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR