Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS)
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0467509 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B157213  Microphone Circuit Open  


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157213 Microphone Circuit Open Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telephone transceiver assembly

·

Communication telematics box

·

Mayday wire

·

Harness or connector


Telematics A

WIRING DIAGRAM

E405960E17
0.906,1.406 1.521,1.604 0.615,0.198 10 false MCMD 1.052,1.813 1.667,2.01 0.615,0.198 10 false SP+ 1.063,2.219 1.677,2.417 0.615,0.198 10 false SP- 0.99,2.594 1.604,2.792 0.615,0.198 10 false MICV 0.938,3.375 1.552,3.573 0.615,0.198 10 false MIC1+ 0.917,2.958 1.531,3.156 0.615,0.198 10 false MIC2+ 1.042,3.792 1.656,3.99 0.615,0.198 10 false MCI- 5.667,1.396 6.281,1.594 0.615,0.198 10 false MCMD 5.667,1.781 6.281,1.979 0.615,0.198 10 false SP+ 5.667,2.198 6.281,2.396 0.615,0.198 10 false SP- 5.656,2.583 6.271,2.781 0.615,0.198 10 false MICV 5.646,3 6.26,3.198 0.615,0.198 10 false MCVD 5.656,3.365 6.271,3.563 0.615,0.198 10 false MCI+ 5.656,3.771 6.271,3.969 0.615,0.198 10 false MCI- 5.531,4.792 6.896,5.188 1.365,0.396 10 false Telephone Transceiver Assembly 4.031,3.99 4.688,4.219 0.656,0.229 10 false * 0.375,4.75 1.438,5.156 1.063,0.406 10 false Communication Telematics Box 0.375,4.583 1.146,4.99 0.771,0.406 10 false P 2.104,1.302 2.719,1.5 0.615,0.198 10 false MCMD 2.26,1.698 2.875,1.896 0.615,0.198 10 false SP+ 2.302,2.104 2.917,2.302 0.615,0.198 10 false SP- 2.198,2.479 2.813,2.677 0.615,0.198 10 false MICV 2.219,3.302 2.833,3.5 0.615,0.198 10 false MCI2 2.219,2.906 2.833,3.104 0.615,0.198 10 false MIC1 2.229,3.677 2.844,3.875 0.615,0.198 10 false MCI- 1.458,1.313 2.073,1.51 0.615,0.198 10 false 1 1.479,1.708 2.094,1.906 0.615,0.198 10 false 3 1.49,2.104 2.104,2.302 0.615,0.198 10 false 8 1.479,2.5 2.094,2.698 0.615,0.198 10 false 5 1.5,3.292 2.115,3.49 0.615,0.198 10 false 2 1.5,2.896 2.115,3.094 0.615,0.198 10 false 7 1.49,3.677 2.104,3.875 0.615,0.198 10 false 4 2.76,1.219 3.375,1.417 0.615,0.198 10 false 1 2.76,1.615 3.375,1.813 0.615,0.198 10 false 3 2.76,2 3.375,2.198 0.615,0.198 10 false 9 2.792,2.406 3.406,2.604 0.615,0.198 10 false 6 2.74,2.792 3.354,2.99 0.615,0.198 10 false 10 2.75,3.198 3.365,3.396 0.615,0.198 10 false 11 2.771,3.594 3.385,3.792 0.615,0.198 10 false 5 5.344,1.677 5.958,1.875 0.615,0.198 10 false 18 5.385,1.292 6,1.49 0.615,0.198 10 false 8 5.354,2.073 5.969,2.271 0.615,0.198 10 false 34 5.354,2.458 5.969,2.656 0.615,0.198 10 false 24 5.396,2.865 6.021,3.063 0.625,0.198 10 false 5 5.396,3.656 6.021,3.854 0.625,0.198 10 false 7 5.531,4.604 6.302,5.01 0.771,0.406 10 false I55 2.729,1.396 3.5,1.802 0.771,0.406 10 false d3 5.646,4.198 6.26,4.396 0.615,0.198 10 false SGND 5.354,4.083 5.979,4.281 0.625,0.198 10 false 23 1.667,4.615 2.781,5.094 1.115,0.479 10 false Mayday Wire 5.396,3.26 6.021,3.458 0.625,0.198 10 false 6 0.344,5.458 2.521,5.781 2.177,0.323 10 false *: Shielded 2.729,1.792 3.5,2.198 0.771,0.406 10 false d3 2.729,2.188 3.5,2.594 0.771,0.406 10 false d3 2.729,2.583 3.5,2.99 0.771,0.406 10 false d3 2.74,2.979 3.51,3.385 0.771,0.406 10 false d3 2.729,3.375 3.5,3.781 0.771,0.406 10 false d3 2.74,3.771 3.51,4.177 0.771,0.406 10 false d3

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

c.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



Post-procedure1

d.

None



A

B

2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)
2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)

Pre-procedure1

a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Disconnect the d3 mayday wire connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I55,d3)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

Click Connector(d3)Body>No. 1 Roof Wire>Communication Telematics Box

I55-8 (MCMD) - d3-1 (MCMD) Always Below 1 Ω
I55-18 (SP+) - d3-3 (SP+) Always Below 1 Ω
I55-34 (SP-) - d3-9 (SP-) Always Below 1 Ω
I55-24 (MICV) - d3-6 (MICV) Always Below 1 Ω
I55-5 (MCVD) - d3-10 (MIC1) Always Below 1 Ω
I55-6 (MCI+) - d3-11 (MCI2) Always Below 1 Ω
I55-7 (MCI-) - d3-5 (MCI-) Always Below 1 Ω
I55-8 (MCMD) or d3-1 (MCMD) - Body ground Always 10 kΩ or higher
I55-18 (SP+) or d3-3 (SP+) - Body ground Always 10 kΩ or higher
I55-34 (SP-) or d3-9 (SP-) - Body ground Always 10 kΩ or higher
I55-24 (MICV) or d3-6 (MICV) - Body ground Always 10 kΩ or higher
I55-5 (MCVD) or d3-10 (MIC1) - Body ground Always 10 kΩ or higher
I55-6 (MCI+) or d3-11 (MCI2) - Body ground Always 10 kΩ or higher
I55-7 (MCI-) or d3-5 (MCI-) - Body ground Always 10 kΩ or higher
I55-23 (SGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)

Pre-procedure1

a.
E409641C15
1.49,2.823 1.865,3.083 0.375,0.26 1.521,0.365 1.896,0.625 0.375,0.26 2.177,1.281 2.646,1.281 true 1.313,3.208 1.708,3.729 true 1.823,1.271 2.542,0.708 true 1.823,1.604 2.479,2.031 true 0.781,1.292 1.208,1.292 true 1.583,1.615 0.938,2.177 true 1.385,1.583 0.906,1.792 true 1.406,1.219 0.896,0.917 true 1,3.396 1.49,3.729 true 0.917,3.771 1.302,3.771 true 1.719,4 1.854,4.365 true 2.25,3.292 1.917,3.719 true 1.313,4.333 1.531,3.979 true 2.5,3.76 2.073,3.76 true 0.365,2.635 0.677,2.833 0.313,0.198 10 false *b 0.292,0.26 0.604,0.458 0.313,0.198 10 false *a 1.646,2.865 1.958,3.063 0.313,0.198 10 false P 1.646,0.417 1.958,0.615 0.313,0.198 10 false d3 2.688,1.208 3.271,1.583 0.583,0.375 10 false MCMD 0.448,3.688 1.031,4.063 0.583,0.375 10 false MCMD 2.583,0.625 3.167,1 0.583,0.375 10 false SP+ 2.531,1.969 3.115,2.344 0.583,0.375 10 false SP- 0.417,1.219 1,1.594 0.583,0.375 10 false MICV 0.5,1.75 1,2.104 0.5,0.354 10 false MCI2 0.563,0.823 1.146,1.198 0.583,0.375 10 false MCI- 0.542,2.115 1.125,2.49 0.583,0.375 10 false MIC1 1.063,3.063 1.646,3.438 0.583,0.375 10 false SP+ 0.563,3.313 1.146,3.688 0.583,0.375 10 false MIC1+ 1.896,4.323 2.531,4.656 0.635,0.333 10 false SP- 2.542,3.698 3.125,4.073 0.583,0.375 10 false MICV 0.927,4.313 1.427,4.667 0.5,0.354 10 false MIC2+ 2.229,3.135 2.813,3.51 0.583,0.375 10 false MCI-
*a Component without harness connected
(Wire Harness)
*b Component without harness connected
(Communication Telematics Box)


Disconnect the d3 wire harness connector.


b.

Disconnect the P communication telematics box connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d3)Location & Routing

Click Connector(d3)Body>No. 1 Roof Wire>Communication Telematics Box

d3-1 (MCMD) - P-1 (MCMD) Always Below 1 Ω
d3-3 (SP+) - P-3 (SP+) Always Below 1 Ω
d3-9 (SP-) - P-8 (SP-) Always Below 1 Ω
d3-6 (MICV) - P-5 (MICV) Always Below 1 Ω
d3-10 (MIC1) - P-2 (MIC1+) Always Below 1 Ω
d3-11 (MCI2) - P-7 (MIC2+) Always Below 1 Ω
d3-5 (MCI-) - P-4 (MCI-) Always Below 1 Ω
d3-1 (MCMD) or P-1 (MCMD) - Body ground Always 10 kΩ or higher
d3-3 (SP+) or P-3 (SP+) - Body ground Always 10 kΩ or higher
d3-9 (SP-) or P-8 (SP-) - Body ground Always 10 kΩ or higher
d3-6 (MICV) or P-5 (MICV) - Body ground Always 10 kΩ or higher
d3-10 (MIC1) or P-2 (MIC1+) - Body ground Always 10 kΩ or higher
d3-11 (MCI2) or P-7 (MIC2+) - Body ground Always 10 kΩ or higher
d3-5 (MCI-) or P-4 (MCI-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

NG

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
E442560C16
1.385,0.573 1.958,0.885 0.573,0.313 2.26,1.948 2.458,2.74 2.458,2.74 2.625,2.74 true 2.292,1.813 2.563,0.969 2.563,0.969 2.729,0.969 true 0.25,0.302 0.563,0.5 0.313,0.198 10 false *a 1.573,0.646 2.115,0.865 0.542,0.219 10 false I55 2.802,0.896 3.344,1.115 0.542,0.219 10 false MCI- 2.677,2.667 3.219,2.885 0.542,0.219 10 false MICV
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I55)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

I55-24 (MICV) - Body ground Ignition switch ON 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I55)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

I55-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK COMMUNICATION TELEMATICS BOX

NG

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
5.CHECK COMMUNICATION TELEMATICS BOX

Pre-procedure1

a.

Replace the communication telematics box with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL



b.

Turn the ignition switch to ON and wait for 10 seconds or more.


c.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



Post-procedure1

e.

None



A

END (COMMUNICATION TELEMATICS BOX IS DEFECTIVE)

B

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT