Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467505 TOYOTA MULTI OPERATION TOUCH SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  B15D6  Display Disconnected (Multi Display)  


DESCRIPTION

The multi-display assembly and integration control sub-assembly are connected by AVC-LAN communication lines.

This DTC is stored when an AVC-LAN communication error occurs between the multi-display assembly and integration control sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15D6 Display Disconnected (Multi Display) A device that is listed in the AVC-LAN connected device record of the integration control sub-assembly is missing
·

Multi-display assembly power source circuit

·

AVC-LAN circuit between integration control sub-assembly and multi-display assembly

·

Multi-display assembly

·

Integration control sub-assembly

·

Harness or connector


D-SEAT SW A

WIRING DIAGRAM

B611430E05
2.656,0.667 3.635,0.896 0.979,0.229 10 false from Battery*2 2.427,1.635 3.927,1.885 1.5,0.25 10 false from ACC Relay*2 4.302,1.813 5.375,2.01 1.073,0.198 10 false ECU-ACC 2.229,3.375 2.688,3.573 0.458,0.198 10 false I22 2.219,3.552 5.188,3.833 2.969,0.281 10 false Integration Control Sub-assembly 5.438,3.854 5.896,4.052 0.458,0.198 10 false I18 5.427,4.031 7.156,4.271 1.729,0.24 10 false Multi-display Assembly 1.156,4.125 3.177,4.313 2.021,0.188 10 false : AVC-LAN Communication Line 3.281,2.469 3.594,2.677 0.313,0.208 10 false TX+ 3.271,2.885 3.573,3.083 0.302,0.198 10 false TX- 3.625,2.375 3.938,2.573 0.313,0.198 10 false 18 3.625,2.771 3.938,2.969 0.313,0.198 10 false 40 5.385,2.375 5.542,2.573 0.156,0.198 10 false 7 5.323,2.781 5.635,2.979 0.313,0.198 10 false 19 5.344,3.25 5.656,3.448 0.313,0.198 10 false 13 5.615,2.458 5.906,2.656 0.292,0.198 10 false TX+ 5.635,2.875 5.917,3.094 0.281,0.219 10 false TX- 5.615,3.354 6.063,3.552 0.448,0.198 10 false GND1 5.615,1.646 5.958,1.823 0.344,0.177 10 false ACC 5.625,0.667 5.781,0.865 0.156,0.198 10 false B 5.344,0.583 5.656,0.781 0.313,0.198 10 false 12 5.354,1.542 5.667,1.74 0.313,0.198 10 false 24 4.375,0.802 5.125,1.063 0.75,0.26 10 false RADIO 1.438,1.177 3.667,1.417 2.229,0.24 10 false from Engine Stop and Start ECU*1 1.448,0.229 3.677,0.469 2.229,0.24 10 false from Engine Stop and Start ECU*1 0.698,4.438 2.99,4.688 2.292,0.25 10 false *1: w/ Stop and Start System 3.24,4.448 5.76,4.677 2.521,0.229 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the integration control sub-assembly, always replace it with a new one. If an integration control sub-assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The integration control sub-assembly may not operate normally.



·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

Procedure1

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

END

B

4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the I18 multi-display assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I18)Location & Routing

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

I18-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Stop and Start System
Tester Connection Condition Specified Condition

Click Location & Routing(I18)Location & Routing

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

I18-12 (B) - I18-13 (GND1) Always 10.5 to 16 V
I18-24 (ACC) - I18-13 (GND1) Ignition switch ON 10.5 to 16 V
I18-24 (ACC) - I18-13 (GND1) Ignition switch ACC 10.5 to 16 V

w/o Stop and Start System
Tester Connection Condition Specified Condition

Click Location & Routing(I18)Location & Routing

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

I18-12 (B) - I18-13 (GND1) Always 11 to 14 V
I18-24 (ACC) - I18-13 (GND1) Ignition switch ON 11 to 14 V
I18-24 (ACC) - I18-13 (GND1) Ignition switch ACC 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

Pre-procedure1

a.

Disconnect the I22 integration control sub-assembly connector.


b.

Disconnect the I18 multi-display assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I22,I18)Location & Routing

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

I22-18 (TX+) - I18-7 (TX+) Always Below 1 Ω
I22-40 (TX-) - I18-19 (TX-) Always Below 1 Ω
I22-18 (TX+) or I18-7 (TX+) - Body ground Always 10 kΩ or higher
I22-40 (TX-) or I18-19 (TX-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.REPLACE MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE MULTI-DISPLAY ASSEMBLY

Pre-procedure1

a.

Replace the multi-display assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL



b.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

END

B