Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1543  Extension Module Disconnected 2  


DESCRIPTION

If the radio receiver assembly cannot detect the navigation ECU assembly for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio receiver assembly confirms that the information is missing by checking past navigation ECU assembly recognition information (registered information), this DTC will be stored.

HINT:

The navigation system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the navigation system will not operate normally.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1543 Extension Module Disconnected 2 Navigation ECU assembly disconnected
·

Navigation ECU assembly

·

Radio receiver assembly

·

Harness or connector


Navigation System A

HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


WIRING DIAGRAM

E466169E01
5.833,2.396 6.771,2.771 0.938,0.375 10 false Radio Receiver Assembly 5.844,2.229 6.292,2.542 0.448,0.313 10 false I157 2.833,2.271 4.74,2.729 1.906,0.458 10 false Navigation ECU Assembly 2.906,1.75 3.229,1.938 0.323,0.188 10 false I21 2.896,0.833 3.177,1.042 0.281,0.208 10 false I21 4.198,0.875 4.552,1.073 0.354,0.198 10 false I158 1.792,1 2.99,1.313 1.198,0.313 10 false ECU-DCC NO.2 0.906,0.823 1.917,1.083 1.01,0.26 10 false from Battery*3 3.302,0.854 3.792,1.25 0.49,0.396 10 false +B 3.292,1.75 3.646,1.948 0.354,0.198 10 false GND 3.708,0.865 4.115,1.063 0.406,0.198 10 false US4+ 3.729,1.313 4.219,1.708 0.49,0.396 10 false US4- 3.667,1.76 4.104,1.927 0.438,0.167 10 false UGD4 5.927,0.875 6.323,1.052 0.396,0.177 10 false US4+ 5.938,1.313 6.323,1.5 0.385,0.188 10 false US4- 5.958,1.792 6.396,1.979 0.438,0.188 10 false UGD4 4.292,0.667 4.708,1.042 0.417,0.375 10 false 4 4.302,1.115 4.719,1.49 0.417,0.375 10 false 5 4.281,1.563 4.698,1.938 0.417,0.375 10 false 6 2.906,0.635 3.323,1.01 0.417,0.375 10 false 10 2.917,1.563 3.333,1.938 0.417,0.375 10 false 23 5.698,0.708 6.115,1.083 0.417,0.375 10 false 4 5.708,1.198 6.125,1.542 0.417,0.344 10 false 5 5.708,1.677 6.125,2.021 0.417,0.344 10 false 6 0.917,3.354 2.667,3.646 1.75,0.292 10 false : USB Communication Line 0.229,3.052 2.417,3.375 2.188,0.323 10 false *3: w/o Stop and Start System 5.104,1.656 5.417,1.885 0.313,0.229 10 false *1 4.198,1.323 4.542,1.531 0.344,0.208 10 false I158 4.219,1.771 4.573,1.938 0.354,0.167 10 false I158 0.219,2.719 2.063,3.063 1.844,0.344 10 false *2: w/ Stop and Start System 0.208,2.417 1.531,2.75 1.323,0.333 10 false *1: Shielded 0.49,0.104 1.823,0.469 1.333,0.365 10 false from Engine Stop and Start ECU*2

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK MAP SCREEN

Pre-procedure1

a.

Turn the ignition switch to ACC and wait for 90 seconds.


Procedure1

b.

Press the "MAP" switch and check that the map screen is displayed normally.


Result:
Result Proceed to
Map screen is displayed normally A
Map screen is not displayed normally B


HINT:
·

This DTC may be stored due to environmental reasons such as electrical noise or interference.

·

Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)



Post-procedure1

c.

None



A

B

2.CHECK DTC
2.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON and wait for 90 seconds.


Procedure1

d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

e.

None



A

B

3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU ASSEMBLY - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the I21 navigation ECU assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I21)Location & Routing

Click Connector(I21)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Navigation ECU Assembly

I21-23 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I21)Location & Routing

Click Connector(I21)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Navigation ECU Assembly

I21-10 (+B) - Body ground Always 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NAVIGATION ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NAVIGATION ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the I157 radio receiver assembly connector.


b.

Disconnect the I158 navigation ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I157,I158)Location & Routing

Click Connector(I157)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I158)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Navigation ECU Assembly

I157-4 (US4+) - I158-4 (US4+) Always Below 1 Ω
I157-5 (US4-) - I158-5 (US4-) Always Below 1 Ω
I157-6 (UGD4) - I158-6 (UGD4) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.REPLACE NAVIGATION ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE NAVIGATION ECU ASSEMBLY
a.

Replace the navigation ECU assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON and wait for 90 seconds.


Procedure1

d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

e.

None



A

END (NAVIGATION ECU ASSEMBLY IS DEFECTIVE)

B