Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D6  Display Disconnected  


DESCRIPTION

The integration control sub-assembly and radio receiver assembly are connected by AVC-LAN communication lines.

This DTC is stored when an AVC-LAN communication error occurs between the integration control sub-assembly and radio receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15D6 Display Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing
·

Integration control sub-assembly power source circuit

·

AVC-LAN circuit between radio receiver assembly and integration control sub-assembly

·

Integration control sub-assembly

·

Radio receiver assembly

·

Harness or connector


Navigation System A

HINT:

The radio receiver assembly is the master unit.


WIRING DIAGRAM

E466177E01
0.333,0.458 1.708,0.823 1.375,0.365 10 false from Engine Stop and Start ECU*1 0.333,1.688 1.708,2.052 1.375,0.365 10 false from Engine Stop and Start ECU*1 0.333,3.01 1.708,3.375 1.375,0.365 10 false from Engine Stop and Start ECU*1 0.833,5.375 5.115,5.573 4.281,0.198 10 false : AVC-LAN Communication Line 3.75,2.354 4.208,2.552 0.458,0.198 10 false ACC 3.625,4.5 4.823,4.896 1.198,0.396 10 false Integration Control Sub-assembly 3.635,4.333 4.094,4.531 0.458,0.198 10 false I22 5.792,4.5 6.719,4.875 0.927,0.375 10 false Radio Receiver Assembly 5.802,4.344 6.26,4.542 0.458,0.198 10 false I10 5.896,1.615 6.51,1.813 0.615,0.198 10 false TX1+ 5.927,2.802 6.542,3 0.615,0.198 10 false TX1- 0.813,1.156 2.646,1.354 1.833,0.198 10 false from Battery*2 2.333,1.333 3.865,1.531 1.531,0.198 10 false ECU-B NO.3 3.719,1.177 3.875,1.375 0.156,0.198 10 false B 3.729,3.688 4.188,3.885 0.458,0.198 10 false IG+ 4.26,3.719 4.719,3.917 0.458,0.198 10 false GND 4.229,1.594 4.844,1.792 0.615,0.198 10 false TX1+ 4.25,2.802 4.865,3 0.615,0.198 10 false TX1- 4.688,1.438 5,1.635 0.313,0.198 10 false 36 4.698,2.635 5.01,2.833 0.313,0.198 10 false 35 4.698,3.604 5.01,3.802 0.313,0.198 10 false 20 3.479,1.031 3.635,1.229 0.156,0.198 10 false 1 3.5,2.26 3.656,2.458 0.156,0.198 10 false 3 3.5,3.594 3.656,3.792 0.156,0.198 10 false 4 5.677,1.438 5.833,1.635 0.156,0.198 10 false 5 5.677,2.646 5.833,2.844 0.156,0.198 10 false 6 2.438,2.542 3.51,2.74 1.073,0.198 10 false ECU-ACC 2.302,3.896 4.292,4.094 1.99,0.198 10 false ECU-IGR NO. 2 0.552,2.375 3,2.573 2.448,0.198 10 false from ACC Relay*2 0.563,3.708 3.01,3.906 2.448,0.198 10 false IGR-NO.2 Relay*2 0.188,5 2.635,5.198 2.448,0.198 10 false *2: w/o Stop and Start System 0.188,4.719 2.635,4.917 2.448,0.198 10 false *1: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the integration control sub-assembly, always replace it with a new one. If an integration control sub-assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The integration control sub-assembly may not operate normally.




PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B



A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

END

B

4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the I22 integration control sub-assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I22)Location & Routing

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

I22-20 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I22)Location & Routing

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

I22-1 (B) - I22-20 (GND) Always 11 to 14 V*1
10.5 to 16 V*2
I22-3 (ACC) - I22-20 (GND) Ignition switch ACC 11 to 14 V*1
10.5 to 16 V*2
I22-4 (IG+) - I22-20 (GND) Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RADIO RECEIVER ASSEMBLY

Pre-procedure1

a.

Disconnect the I10 radio receiver assembly connector.


Procedure1

b.
E466181C01
1.542,0.75 1.958,1.021 0.417,0.271 2.917,2.792 2.656,2.063 false 2.292,2.771 2.521,2.052 false 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a 1.656,0.802 1.969,1 0.313,0.198 10 false I10 2.792,2.854 3.219,3.083 0.427,0.229 10 false TX1+ 2.146,2.844 2.76,3.042 0.615,0.198 10 false TX1-
*a Component without harness connected
(Radio Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (TX1+) - 6 (TX1-) Always 60 to 80 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)

Pre-procedure1

a.

Disconnect the I10 radio receiver assembly connector.


b.

Disconnect the I22 integration control sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I10,I22)Location & Routing

Click Connector(I10)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

I10-5 (TX1+) - I22-36 (TX1+) Always Below 1 Ω
I10-6 (TX1-) - I22-35 (TX1-) Always Below 1 Ω
I10-5 (TX1+) or I22-36 (TX1+) - Body ground Always 10 kΩ or higher
I10-6 (TX1-) or I22-35 (TX1-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

7.REPLACE INTEGRATION CONTROL SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE INTEGRATION CONTROL SUB-ASSEMBLY

Pre-procedure1

a.

Replace the integration control sub-assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY ECU>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

END (INTEGRATION CONTROL SUB-ASSEMBLY IS DEFECTIVE)

B