Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM
RM38G0E _51 Engine / Hybrid System _101047 STOP AND START _0469044 STOP AND START SYSTEM U

STOP AND START  STOP AND START SYSTEM  TERMINALS OF ECU  


ENGINE STOP AND START ECU


B412468E45
5.031,0.219 5.458,0.469 0.427,0.25 3.219,0.208 3.646,0.458 0.427,0.25 1.563,0.208 1.99,0.458 0.427,0.25 3.292,0.25 3.75,0.448 0.458,0.198 10 false B38 1.635,0.25 2.125,0.448 0.49,0.198 10 false B37 5.125,0.26 5.583,0.458 0.458,0.198 10 false I57

a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
B37-1 (BIN2) - Body ground Battery Always 9.5 to 14 V
B37-2 (GND2) - Body ground Ground Always Below 1 Ω
B37-3 (BIN1) - Body ground Battery Always 9.5 to 14 V
B37-8 (GND1) - Body ground Ground Always Below 1 Ω
B38-1 (+B) - Body ground Power source of engine stop and start ECU Ignition switch ON 9.5 to 14 V
B38-6 (DGND) - Body ground Ground Always Below 1 Ω
B38-10 (NE) - Body ground Engine speed signal from ECM Always 10 kΩ or higher
I57-13 (CANH) - Body ground CAN communication Always 200 Ω or higher
I57-14 (CANL) - Body ground CAN communication Always 200 Ω or higher
I57-15 (LC1H) - Body round Local bus communication line Always 200 Ω or higher
I57-16 (LC1L) - Body round Local bus communication line Always 200 Ω or higher
I57-18 (IGP) - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V
I57-19 (ACC) - Body ground Ignition switch signal Ignition switch ACC 9.5 to 14 V
I57-21 (IGR) - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V


c.

Reconnect the engine stop and start ECU connectors.


d.

Measure the voltage and pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
B37-6 (OP21) - B38-6 (DGND) Oil pump with motor assembly drive power source signal One of the following conditions is met:
·

Engine stopped by stop and start system control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed


10.5 to 16 V
B38-7 (BNT1) - B38-6 (DGND) Engine hood courtesy switch (hood lock assembly) signal
·

Ignition switch ON

·

Engine stopped

·

Engine hood closed


Below 1.5 V
·

Ignition switch ON

·

Engine stopped

·

Engine hood open


8 to 14 V
B38-9 (OPM1) - B38-6 (DGND) Oil pump with motor assembly directions signal One of the following conditions is met:
·

Engine stopped by stop and start system control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed


Pulse generation
(See waveform 1)
B38-10 (NE) - B38-6 (DGND) Engine speed signal from ECM Idling after engine warmed up Pulse generation
(See waveform 2)
B38-17 (CLL) - B38-6 (DGND) Park/Neutral position switch assembly signal
·

Ignition switch ON

·

Shift lever not in P or N


8 to 14 V
·

Ignition switch ON

·

Shift lever in P or N


Below 3.0 V
B38-19 (DON2) - B38-6 (DGND) External backup boost converter (eco run vehicle converter assembly) signal Engine running Pulse generation
(See waveform 3)
B38-21 (STA) - B38-6 (DGND) Starter pinion operation signal Cranking 6.0 V or more
B38-23 (STA2) - B38-6 (DGND) Starter motor operation signal Cranking 6.0 V or more
B38-27 (NOPM) - B38-6 (DGND) Oil pump with motor assembly speed signal One of the following conditions is met:
·

Engine stopped by stop and start system control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed


Pulse generation
(See waveform 4)
I57-2 (B41) - B38-6 (DGND) Backup boost converter signal Always 10.5 to 16 V
I57-3 (IG41) - B38-6 (DGND) Backup boost converter signal Ignition switch ON 10.5 to 16 V
I57-5 (ECAN) - B38-6 (DGND) Stop and start system cancel switch (combination switch assembly) signal
·

Ignition switch ON

·

Stop and start system cancel switch (combination switch assembly) pressed


Below 1.5 V
·

Ignition switch ON

·

Stop and start system cancel switch (combination switch assembly) not pressed


8 to 14 V
I57-10 (IG12) - B38-6 (DGND) Backup boost converter signal Ignition switch ON 10.5 to 16 V
I57-11 (B43) - B38-6 (DGND) Backup boost converter signal Always 10.5 to 16 V
I57-12 (B42) - B38-6 (DGND) Backup boost converter signal Always 10.5 to 16 V
I57-18 (IGP) - B38-6 (DGND) Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
I57-19 (ACC) - B38-6 (DGND) Ignition switch signal Ignition switch off Below 1 V
Ignition switch ACC 9.5 to 14 V
I57-21 (IGR) - B38-6 (DGND) Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
I57-23 (IG31) - B38-6 (DGND) Backup boost converter signal Ignition switch ON 10.5 to 16 V
I57-26 (AC42) - B38-6 (DGND) Backup boost converter signal Ignition switch ACC 10.5 to 16 V


e.
A329962E11
2.885,1.25 3.344,1.448 0.458,0.198 10 false GND

Waveform 1

Item Content
Tester Connection B38-9 (OPM1) - B38-6 (DGND)
Tool Setting 5 V/DIV., 5 ms./DIV.
Condition One of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed




f.
A318633E22
2.792,1.042 3.25,1.24 0.458,0.198 10 false GND

Waveform 2

Item Content
Tester Connection B38-10 (NE) - B38-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling after engine warmed up


g.
A199267E15
2.917,1.198 3.375,1.396 0.458,0.198 10 false GND

Waveform 3

Item Content
Tester Connection B38-19 (DON2) - B38-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Engine running


h.
A112562E19
2.844,1.219 3.156,1.375 0.313,0.156 10 false GND

Waveform 4

Item Content
Tester Connection B38-27 (NOPM) - B38-6 (DGND)
Tool Setting 5 V/DIV., 5 ms./DIV.
Condition One of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed