If any of the following DTCs are stored, the engine stop and start ECU enters fail-safe mode to preserve vehicle operability.
| DTC | Component | Fail-safe Operation | Fail-safe Deactivation Condition |
|---|---|---|---|
| P033562 | Open in engine speed signal circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
All of the following conditions are met for 10 seconds:
·
Normal communication with ECM
·
Engine speed 500 rpm or higher
·
Engine speed (communication signal) 500 rpm or higher
·
Difference between engine speed from pulse signal and engine speed from communication signal is less than 300 rpm |
| P060629 | Engine stop and start ECU |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P060B1C P060B49 P060B71 |
Analog to digital converter (Engine stop and start ECU) | Stop and start control is prohibited | Pass condition detected and ignition switch turned to ON |
| P061519 | ST relay circuit | Stop and start control is prohibited | Pass condition detected and DTCs are cleared |
| P061562 | Starter circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with ECM returns to normal and one of the following conditions is met:
·
The STA signal detected by the ECM and STA signals detected by the engine stop and start ECU are on for 0.3 seconds
·
The STA signal detected by the ECM and STA signals detected by the engine stop and start ECU are off for 5 seconds |
| P094296 | Oil pump with motor assembly circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and DTCs are cleared |
| P0C2B11 P0C2B15 P279796 |
Oil pump with motor assembly circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P161D9E | Starter delay circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
·
Pass condition detected and ignition switch turned to ON
·
Time between STA (for starter pinion) turning on and STA2 (for starter motor) turning on becomes 0.016 seconds or more |
| P164400 |
·
Starter drive circuit
·
ST NO. 1 relay
·
ST NO. 2 relay
·
Engine stop and start ECU |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Voltage of engine stop and start ECU internal drive circuit for starter is correct when engine is idling and restarted |
| P16449E | Engine stop and start ECU |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P253014 | IG signal circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
All of the following conditions are met for 10 seconds or more:
·
Ignition switch ON
·
Normal communication with ECM
·
Ignition switch (communication) ON. |
| P30DF62 P30EF4B P323A00 P323A16 P323AA2 P323B29 P323B38 |
Backup boost converter circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and DTCs are cleared |
| P323A19 | Backup boost converter circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
·
Pass condition detected and ignition switch turned to ON
·
DTCs (for overcurrent caused by audio volume setting) are cleared |
| P33B300 | External backup boost converter (eco run vehicle converter assembly) circuit |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
1 second after external backup boost converter (eco run vehicle converter assembly) circuit becomes idle |
| U010087 | CAN communication (ECM) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 2 seconds |
| U010187 | CAN communication (TCM) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 21.6 seconds |
| U011487 | CAN communication (4 wheel drive control ECU) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 2 seconds |
| U012687 | CAN communication (steering sensor) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 2 seconds |
| U012987 | CAN communication (skid control ECU (brake actuator assembly)) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 4.4 seconds |
| U014087 | CAN communication (main body ECU (multiplex network body ECU)) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 7.2 seconds |
| U015187 | CAN communication (airbag sensor assembly) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 21.2 seconds |
| U015587 | CAN communication (combination meter assembly) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 21.2 seconds |
| U016487 | CAN communication (air conditioning amplifier assembly) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 21.2 seconds |
| U111087 | CAN communication (clearance warning ECU assembly) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 2 seconds |
| U114C87 | CAN communication (suspension control ECU) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 2.2 seconds |
| U117087 | Local CAN communication (skid control ECU (brake actuator assembly)) |
·
Stop and start control is prohibited
·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 21.2 seconds |