FREEZE FRAME DATA
The absorber control ECU stores system condition information as freeze frame data the moment a DTC is stored. The Freeze Frame Data can be displayed using the GTS.
Freeze frame data when a DTC is stored.
Freeze frame data is stored the moment a DTC is stored.
When freeze frame data is stored when a DTC is stored, the data is not updated or deleted until DTCs are cleared.
CHECK FREEZE FRAME DATA
Select a DTC to display the freeze frame data.
Check the freeze frame data for the output DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| (Up&Down)G Sensor FR | Front acceleration sensor RH (up and down) | Min.: -1045.29 m/s2 Max.: 1045.26 m/s2 |
-0.98 to 0.98 m/s2 when stationary | The value changes when the vehicle (front RH) is bounced. |
| (Up&Down)G Sensor FL | Front acceleration sensor LH (up and down) | Min.: -1045.29 m/s2 Max.: 1045.26 m/s2 |
-0.98 to 0.98 m/s2 when stationary | The value changes when the vehicle (front LH) is bounced. |
| (Up&Down)G Sensor Rear | Rear acceleration sensor (up and down) | Min.: -1045.29 m/s2 Max.: 1045.26 m/s2 |
-0.98 to 0.98 m/s2 when stationary | The value changes when the vehicle (rear) is bounced. |
| IG Power Source Voltage | ECU power supply voltage | Min.: 0.0 V Max.: 25.5 V |
11 to 14 V (Actual ECU power supply voltage): Ignition switch ON | - |
| G Sensor Voltage | G sensor power supply voltage | Min.: 0.0 V Max.: 25.5 V |
4.8 to 5.2 V | - |
| ECU Substrate Temperature | Current ECU substrate temperature | Min.: 40°C (104°F) Max.: 120°C (248°F) |
Displays current ECU substrate temperature | - |
| FR Solenoid Aim Electric Current Level for Control | Target solenoid current value (front wheel RH) | Min.: 0 mA Max.: 2040 mA |
Changes depending on step count | - |
| FL Solenoid Aim Electric Current Level for Control | Target solenoid current value (front wheel LH) | Min.: 0 mA Max.: 2040 mA |
Changes depending on step count | - |
| RR Solenoid Aim Electric Current Level for Control | Target solenoid current value (rear wheel RH) | Min.: 0 mA Max.: 2040 mA |
Changes depending on step count | - |
| RL Solenoid Aim Electric Current Level for Control | Target solenoid current value (rear wheel LH) | Min.: 0 mA Max.: 2040 mA |
Changes depending on step count | - |
| FR Solenoid Electric Current | Solenoid current value (front wheel RH) | Min.: 0 mA Max.: 2040 mA |
Changes depending on step count | - |
| FL Solenoid Electric Current | Solenoid current value (front wheel LH) | Min.: 0 mA Max.: 2040 mA |
Changes depending on step count | - |
| RR Solenoid Electric Current | Solenoid current value (rear wheel RH) | Min.: 0 mA Max.: 2040 mA |
Changes depending on step count | - |
| RL Solenoid Electric Current | Solenoid current value (rear wheel LH) | Min.: 0 mA Max.: 2040 mA |
Changes depending on step count | - |
| Number of Trouble Codes | Number of DTCs stored | Min.: 0 Max.: 255 |
0 | - |