Home › Suspension › SUSPENSION CONTROL › ADAPTIVE VARIABLE SUSPENSION SYSTEM
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0469072 ADAPTIVE VARIABLE SUSPENSION SYSTEM U

SUSPENSION CONTROL  ADAPTIVE VARIABLE SUSPENSION SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

According to the display on the GTS, read the Data List.

Chassis > Adaptive Variable Suspension System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
(Up&Down)G Sensor FR Front acceleration sensor RH (up and down) Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
-0.98 to 0.98 m/s2 when stationary The value changes when the vehicle (front RH) is bounced.
(Up&Down)G Sensor FL Front acceleration sensor LH (up and down) Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
-0.98 to 0.98 m/s2 when stationary The value changes when the vehicle (front LH) is bounced.
(Up&Down)G Sensor Rear Rear acceleration sensor (up and down) Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
-0.98 to 0.98 m/s2 when stationary The value changes when the vehicle (rear) is bounced.
Gravity Sensor(Side to Side) Acceleration sensor (side to side) Min.: -1176.37 m/s2
Max.: 1176.33 m/s2
Changes depending on acceleration generated when turning -
Stop Light Switch Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
SPORT Switch Drive mode select switch (combination switch assembly) ON or OFF ON: During Sport S+ mode or Custom mode (when the CHASSIS item is set to SPORT)
OFF: Not in Sport S+ mode or Custom mode (when the CHASSIS item is set to SPORT)
-
HV Ready HV ready ON or OFF OFF: Always This item is displayed on the GTS but is not required for diagnosis or repair.
TC Terminal TC Terminal ON or OFF ON: DTC output
OFF: DTC not output
-
L4 Switch Transfer position switch ON or OFF ON: Transfer position switch set to L4
OFF: Transfer position switch set to H4
-
IG Power Source Voltage ECU power supply voltage Min.: 0.0 V
Max.: 25.5 V
11 to 14 V (Actual ECU power supply voltage): Ignition switch ON -
Steering Angle Steering angle sensor reading Min.: -49152.0 deg
Max.: 49150.5 deg
Actual steering angle
Steering wheel turned left: Reading increases
Steering wheel turned right: Reading decreases
-
Engine Speed Engine speed Min.: 0 rpm
Max.: 25500 rpm
Actual engine speed -
FR Wheel Speed Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 255 km/h (159 mph)
Actual vehicle speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 255 km/h (159 mph)
Actual vehicle speed No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 255 km/h (159 mph)
Actual vehicle speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 255 km/h (159 mph)
Actual vehicle speed No large fluctuations when driving at a constant speed.
Driving Torque Driving torque Min.: -1024 Nm
Max.: 1023 Nm
- -
Damper Step FR Damper step (Front RH) min.: 1 step
max.: 255 step
- Unused
Damper Step FL Damper step (Front LH) min.: 1 step
max.: 255 step
- Unused
Damper Step RR Damper step (Rear RH) min.: 1 step
max.: 255 step
- Unused
Damper Step RL Damper step (Rear LH) min.: 1 step
max.: 255 step
- Unused
Adaptive Variable Suspension(AVS) Mode Adaptive variable suspension system (AVS) mode NORMAL, COMFORT, SEMI CO, SEMI SP or SPORTS NORMAL: Not in Sport S+ mode or Custom mode (when the CHASSIS item is set to SPORT)
SPORTS: During Sport S+ mode or Custom mode (when the CHASSIS item is set to SPORT)
-
Compatible Constant Information Information used to change the compatible constant Min.: 0
Max.: 255
- -
Identical Constant Information Information used to change the identical constant Min.: 0
Max.: 255
- -
Design Constant Information Information used to change the design constant Min.: 0
Max.: 255
- -
AVS Control Information FR AVS control information (front wheel RH) Min.: 0
Max.: 255
- -
AVS Control Information FL AVS control information (front wheel LH) Min.: 0
Max.: 255
- -
AVS Control Information RR AVS control information (rear wheel RH) Min.: 0
Max.: 255
- -
AVS Control Information RL AVS control information (rear wheel LH) Min.: 0
Max.: 255
- -
Vehicle Information (Conv/HV) Vehicle identification information (hybrid vehicle or except hybrid vehicle) Unknown, Conv or HV Conv: When vehicle identification normal When "Unknown", DTC C1789 is output.
Stop and Start Learning Status Learning status of stop and start setting availability after vehicle identification information registration is performed Unset, OFF or ON OFF: w/o Stop and start system
ON: w/ Stop and start system
When "Unset", DTC C1789 is output.
Overheat Protection Control Count Number of times overheat protection was performed in past Min.: 0
Max.: 255
Displays number of times overheat protection was performed in past -
ECU Substrate Maximum Temperature Stored ECU substrate maximum temperature Min.: 40°C (104°F)
Max.: 120°C (248°F)
Displays maximum temperature of ECU substrate in past -
Status of Overheat Protection Control Current overheat protection status ON or OFF OFF: No overheat protection ON: When overheat protection is on, damping force control stops until the temperature drops below a certain value.
G Sensor Voltage G sensor power supply voltage Min.: 0 V
Max.: 25.5 V
4.8 to 5.2 V -
ECU Substrate Temperature Current ECU substrate temperature Min.: 40°C (104°F)
Max.: 120°C (248°F)
Displays current ECU substrate temperature -
FR Solenoid Aim Electric Current Level for Control Target solenoid current value (front wheel RH) Min.: 0 mA
Max.: 2040 mA
Changes depending on step count -
FL Solenoid Aim Electric Current Level for Control Target solenoid current value (front wheel LH) Min.: 0 mA
Max.: 2040 mA
Changes depending on step count -
RR Solenoid Aim Electric Current Level for Control Target solenoid current value (rear wheel RH) Min.: 0 mA
Max.: 2040 mA
Changes depending on step count -
RL Solenoid Aim Electric Current Level for Control Target solenoid current value (rear wheel LH) Min.: 0 mA
Max.: 2040 mA
Changes depending on step count -
FR Solenoid Drive Duty Solenoid drive duty value (front wheel RH) Min.: 0%
Max.: 100%
Changes depending on step count -
FL Solenoid Drive Duty Solenoid drive duty value (front wheel LH) Min.: 0%
Max.: 100%
Changes depending on step count -
RR Solenoid Drive Duty Solenoid drive duty value (rear wheel RH) Min.: 0%
Max.: 100%
Changes depending on step count -
RL Solenoid Drive Duty Solenoid drive duty value (rear wheel LH) Min.: 0%
Max.: 100%
Changes depending on step count -
FR Solenoid Electric Current Solenoid current value (front wheel RH) Min.: 0 mA
Max.: 2040 mA
Changes depending on step count -
FL Solenoid Electric Current Solenoid current value (front wheel LH) Min.: 0 mA
Max.: 2040 mA
Changes depending on step count -
RR Solenoid Electric Current Solenoid current value (rear wheel RH) Min.: 0 mA
Max.: 2040 mA
Changes depending on step count -
RL Solenoid Electric Current Solenoid current value (rear wheel LH) Min.: 0 mA
Max.: 2040 mA
Changes depending on step count -
Air suspension Learning Status Learning status of air suspension system setting availability after vehicle identification information registration is performed Unset, OFF or ON OFF When "Unset", DTC C1789 is output.
Status of IGP Information (IGP_PT2) Status of IGP information (IGP_PT2) ON or OFF - Unused
Status of IGP Information (IGP_PT1) Status of IGP information (IGP_PT1) ON or OFF - Unused
Status of IGP Relay Coil Status of IGP relay coil ON or OFF - Unused
Status of IG Switch OFF While Driving Status of IG switch OFF while driving Other or OFF - Unused
Off-road Mode Select Signal Off-road mode select signal status NORMAL, GRASS&SNOW, MUD & SAND, LOOSE, ROCK, MOGUL, ROCK & DIRT, ROCK, TRAIL MODE, DIRT, ALL TERRAIN, MUD, SAND or DEEP SNO - Unused
Towing Mode Select Signal Towing mode select signal status Normal, Light or Heavy - Unused
Steering Angle Sensor Wrong Installation Status Steering angle sensor wrong installation status Unknown, Wrong Installation or Correct Installation - Unused
Steering Angle Zero Point Calculated Value Steering angle zero point calculated value Unkown or 3070.5 - Unused
Number of Trouble Codes Number of DTCs stored Min.: 0
Max.: 255
0 -


PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnosis time. Data List information can be displayed while performing Active Tests.


a.

According to the display on the GTS, perform the Active Test.

Chassis > Adaptive Variable Suspension System > Active Test
Tester Display Measurement Item Restrict Condition
Four-Wheel Damping Force Full Hard Four-wheel damper step fixed at full hard
·

Vehicle stopped

·

Engine idling

·

When the actuator system is normal

·

When the power source voltage system is normal


Four-Wheel Damping Force Full Soft Four-wheel damper step fixed at full soft
·

Vehicle stopped

·

Engine idling

·

When the actuator system is normal

·

When the power source voltage system is normal


Damper Step FR (Electric Current) Changes damping force (front RH)
·

Vehicle stopped

·

Engine idling

·

When the actuator system is normal

·

When the power source voltage system is normal


Damper Step FL (Electric Current) Changes damping force (front LH)
·

Vehicle stopped

·

Engine idling

·

When the actuator system is normal

·

When the power source voltage system is normal


Damper Step RR (Electric Current) Changes damping force (rear RH)
·

Vehicle stopped

·

Engine idling

·

When the actuator system is normal

·

When the power source voltage system is normal


Damper Step RL (Electric Current) Changes damping force (rear LH)
·

Vehicle stopped

·

Engine idling

·

When the actuator system is normal

·

When the power source voltage system is normal