Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ROAD SIGN ASSIST SYSTEM
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0469140 ROAD SIGN ASSIST SYSTEM L

ADVANCED DRIVER ASSISTANCE SYSTEM  ROAD SIGN ASSIST SYSTEM  PRECAUTION  


HANDLING PRECAUTION FOR ROAD SIGN ASSIST SYSTEM


a.

The system may not detect traffic signs under the following conditions:

·

The forward recognition camera is misaligned.

·

Dirt, snow, ice or a sticker is on the windshield glass in front of the forward recognition camera.

·

The windshield glass in front of the forward recognition camera is fogged up.

·

The vehicle is significantly tilted.

·

Driving in bad weather (heavy rain or snow, or dense fog), water or snow, etc., is kicked up by the preceding vehicle.

·

The headlights of an oncoming vehicle or sunlight is shining directly on the forward recognition camera.

·

A very bright light from reflective objects, such as a road sign, road surface, another vehicle, etc., is shining directly into the lens of the forward recognition camera.

·

The road sign is dirty, faded, tilted, or has a sticker attached.

·

The sign is dirty, faded or tilted, or the contrast of an electronic sign is low.

·

Whole or part of the sign is blocked by an object.

·

The vehicle passes the sign too quickly after the sign comes into view.

·

When in low light conditions or when the surrounding brightness changes suddenly.

·

The sign is located immediately after a right or left turn.

·

The sign is posted in a position too far away from the forward recognition camera.

·

The sign is posted in a position that is too low compared to the vehicle.

·

The sign is posted on the opposite side of an intersection or curve.

·

The map information in the navigation system is old.*

·

The navigation system cannot be used.*

*: w/ Navigation System




b.

The system may incorrectly recognize traffic signs under the following conditions:

·

A sign is on an adjacent lane or side road, or immediately after traffic lanes merge or diverge.

·

A sticker or graphic is on the rear of a preceding vehicle.

·

An object which is not a traffic sign is similar in appearance.

·

When there are multiple signs.

·

When a sign for certain kinds of vehicles, such as trucks, is detected.

·

The system has not completed learning after entering a different country.




TROUBLESHOOTING PRECAUTIONS


a.

If a terminal contact point malfunction or part installation problem occurs, removal and reinstallation of the suspected part may return the system to normal. However, be aware that the normal condition may only be temporary.


b.

Before disconnecting connectors or removing/installing parts, determine the malfunctioning area by checking and writing down the vehicle condition at the time the malfunction occurred (DTC outputs etc.).


c.

Be sure to check for DTCs related to other systems. The road sign assist system may be influenced by malfunctions in other systems.



HANDLING PRECAUTIONS


a.

Make sure that the ignition switch is off unless otherwise specified in the inspection procedure.


b.

After removal/installation, check for DTCs and confirm that a normal system code is output.



REPLACEMENT PRECAUTIONS


a.

Forward recognition camera:

i.

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT



ii.

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.


iii.

Do not damage the forward recognition camera lens or allow it to become dirty.

NOTICE:

If the forward recognition camera lens has been touched, replace it with a new forward recognition camera.



iv.

Do not use a forward recognition camera if it has been dropped or subjected to any strong impact.


v.

When the forward recognition camera is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



b.

Windshield glass:

i.

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket or the road sign assist system may not operate properly due to a difference in the transmissivity or black ceramic border.


ii.

Do not attach stickers, including transparent stickers, or other items to the outer side of the windshield glass within the area in front of the forward recognition camera.