Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM D

1GR-FE ENGINE CONTROL  SFI SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


A103809E88
2.354,0.135 3.229,0.302 0.875,0.167 10 DTC stored 1.271,1.031 2.052,1.208 0.781,0.177 10 0.5 seconds 0.323,1.031 1.104,1.229 0.781,0.198 10 0.5 seconds 0.354,2.792 2.688,2.948 2.333,0.156 10 Freeze frame data which can be read 2.25,1.031 3.031,1.229 0.781,0.198 10 0.5 seconds

The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

HINT:

If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.


The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the GTS, 5 separate sets of freeze frame data can be checked.

·

3 data sets before the DTC was stored.

·

1 data set when the DTC was stored.

·

1 data set after the DTC was stored.


These data sets can be used to simulate the condition of the vehicle around the time of the occurrence the malfunction. The data may assist in identifying the cause of the malfunction, and judging whether it was temporary or not.


PENDING FREEZE FRAME DATA


HINT:

Pending freeze frame data is stored when a 2 trip DTC is first detected during the first trip.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Select a DTC in order to display its pending freeze frame data.

HINT:
·

Pending freeze frame data is cleared when any of the following occurs.

-

DTCs are cleared using the GTS.


-

The cable is disconnected from the negative (-) battery terminal.


-

40 trips with the engine fully warmed up have been performed after returning to normal. (Pending freeze frame data will not be cleared by only returning the system to normal.)


·

With previous pending freeze frame data stored, if pending freeze frame data is newly stored when a 2 trip DTC is detected in the first trip, the old freeze frame data will be replaced with the new data of the newly detected DTC in the next trip.



A251781E14
0.156,0.104 6.896,0.594 6.74,0.49 10 When a DTC is detected in both the first and second trips but the system returns to normal from the third trip (2 trip logic DTC): 0.146,1.625 1.24,1.802 1.094,0.177 10 Ignition Switch 1.302,1.458 2.115,1.75 0.813,0.292 10 ON 1.302,1.844 1.552,2.021 0.25,0.177 10 Off 0.156,2.583 1.198,2.896 1.042,0.313 10 Pending Freeze Frame Data 1.333,2.5 1.781,2.698 0.448,0.198 10 Stored 1.323,2.781 1.833,3.104 0.51,0.323 10 Not Stored 0.125,3.708 1.031,4.438 0.906,0.729 10 Freeze Frame Data 1.292,3.667 1.74,3.865 0.448,0.198 10 Stored 0.365,4.698 1.75,4.906 1.385,0.208 10 : Malfunction detected 0.365,5 2.083,5.208 1.719,0.208 10 : Malfunction not detected 2.073,0.885 2.76,1.094 0.688,0.208 10 (First Trip) 2.823,0.885 3.781,1.125 0.958,0.24 10 (Second Trip) 3.781,0.885 4.74,1.125 0.958,0.24 10 (Third Trip) 4.594,0.896 5.552,1.135 0.958,0.24 10 (Fourth Trip) 1.302,3.938 1.813,4.26 0.51,0.323 10 Not Stored

A251782E16
0.188,0.177 7.063,0.594 6.875,0.417 10 When 2 trip DTC is first detected in the first trip and another 2 trip DTC is first detected in the second trip: 0.604,1.531 1.521,1.844 0.917,0.313 10 Ignition Switch 1.781,1.365 2.302,1.583 0.521,0.219 10 ON 1.781,1.719 2.125,1.896 0.344,0.177 10 Off 0.479,2.323 1.542,2.688 1.063,0.365 10 Pending Freeze Frame Data A 0.479,3.271 1.542,3.635 1.063,0.365 10 Pending Freeze Frame Data B 1.781,2.25 2.24,2.417 0.458,0.167 10 Stored 1.781,3.156 2.24,3.323 0.458,0.167 10 Stored 1.781,2.531 2.24,2.927 0.458,0.396 10 Not Stored 1.781,3.448 2.24,3.844 0.458,0.396 10 Not Stored 0.677,4.104 3.188,4.344 2.51,0.24 10 : Pending malfunction A detected 0.677,4.573 3.188,4.813 2.51,0.24 10 : Pending malfunction B detected 0.677,5.042 2.771,5.271 2.094,0.229 10 : No malfunction detected 4.198,2.875 5.302,3.052 1.104,0.177 10 Uploaded 2.635,0.719 3.333,1.031 0.698,0.313 10 (First Trip) 3.542,0.719 4.677,0.99 1.135,0.271 10 (Second Trip) 4.604,0.719 5.729,1.052 1.125,0.333 10 (Third Trip) 5.521,0.719 6.719,1.052 1.198,0.333 10 (Fourth Trip)



LIST OF FREEZE FRAME DATA


Powertrain > Engine
Tester Display
Total Distance Traveled
Total Distance Traveled - Unit
Vehicle Speed
Engine Speed
Calculate Load
Vehicle Load
Mass Air Flow Sensor
Atmospheric Pressure
Coolant Temperature
Intake Air Temperature
Ambient Temperature
Engine Run Time
IG-ON Coolant Temperature
Initial Engine Coolant Temperature
IG-ON Intake Air Temperature
Initial Engine Intake Air Temperature
Battery Voltage
BATT Voltage
IG2 / IGP
IGR
Glow Indicator Supported
Accelerator Position
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %
Accelerator Position Sensor No.1 Voltage
Accelerator Position Sensor No.2 Voltage
Accelerator Idle Position
Accelerator Position Sensor No.1 Fully Closed Learn Value
Accelerator Position Sensor No.2 Fully Closed Learn Value
Engine Starting Torque Control Count
Throttle Position Sensor No.1 Voltage %
Throttle Position Sensor No.2 Voltage %
System Guard
Open Side Malfunction
Throttle Request Position
Throttle Sensor Position
Throttle Position Sensor No.1 Voltage
Throttle Position Sensor No.2 Voltage
Throttle Position Command
Throttle Position Sensor Open Position No.1
Throttle Position Sensor Open Position No.2
Throttle Motor Current
Throttle Motor Duty Ratio
Throttle Motor Duty Ratio (Open)
Throttle Motor Duty Ratio (Close)
Throttle Position Sensor Fully Closed Learn Value
+BM Voltage
Actuator Power Supply
Low Revolution Control
N Range Status
ISC F/B Learn Torque
ISC Total AUXS Torque
ISC F/B Torque
Sum of ISC F/B Torque (Recent)
ISC AUXS Torque (Alternator)
ISC AUXS Torque (Air Conditioner)
Throttle Air Flow F/B Value
Throttle Position
Fuel Pump Control Duty Ratio
Injector Cylinder #1 (Port)
Injection Volume Cylinder #1
Injection Volume
Current Fuel Type
EVAP (Purge) VSV
Target Air-Fuel Ratio
A/F (O2) Lambda Sensor B1S1
A/F (O2) Lambda Sensor B2S1
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B2S1
A/F (O2) Sensor Heater Duty Ratio B1S1
A/F (O2) Sensor Heater Duty Ratio B2S1
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
O2 Sensor Impedance B1S2
O2 Sensor Impedance B2S2
O2 Sensor Heater B1S2
O2 Sensor Heater B2S2
O2 Sensor Heater Current Value B1S2
O2 Sensor Heater Current Value B2S2
Short FT B1S1
Short FT B2S1
Long FT B1S1
Long FT B2S1
Total FT Bank 1
Total FT Bank 2
Fuel System Status Bank 1
Fuel System Status Bank 2
Air Pump Pressure (Absolute) Bank 1
Air Pump Pressure (Absolute) Bank 2
Air Pump Pulsation Pressure Bank 1
Air Pump Pulsation Pressure Bank 2
Air Switching Valve Freeze Bank 1
Air Switching Valve Freeze Bank 2
2nd Air System Status
Air Pump (OBD Request)
Air Pump Freeze Bank 1
Air Pump Heater Current-Carrying Status
Atmosphere Adoption (Secondary Air)
Air Injection Test
Subfreezing Conditions
Subfreezing Air Injection Operation
Ignition Timing Cylinder #1
Knock F/B Value
Knock Correct Learn Value
Idle Spark Advance Control Cylinder #1
Idle Spark Advance Control Cylinder #2
Idle Spark Advance Control Cylinder #3
Idle Spark Advance Control Cylinder #4
Idle Spark Advance Control Cylinder #5
Idle Spark Advance Control Cylinder #6
VVT Advance Fail
Intake VVT Hold Learn Value Bank 1
Intake VVT Hold Learn Value Bank 2
Intake VVT Change Angle Bank 1
Intake VVT Change Angle Bank 2
Intake VVT OCV Control Duty Ratio Bank 1
Intake VVT OCV Control Duty Ratio Bank 2
Exhaust VVT Hold Learn Value Bank 1
Exhaust VVT Hold Learn Value Bank 2
Exhaust VVT Change Angle Bank 1
Exhaust VVT Change Angle Bank 2
Exhaust VVT OCV Control Duty Ratio Bank 1
Exhaust VVT OCV Control Duty Ratio Bank 2
Intake VVT Target Angle Bank 1
Intake VVT Target Angle Bank 2
Exhaust VVT Target Angle Bank 1
Exhaust VVT Target Angle Bank 2
Catalyst Temperature B1S1
Catalyst Temperature B2S1
Catalyst Temperature B1S2
Catalyst Temperature B2S2
Starter SW
Neutral Position SW
Shift SW Status (Neutral) Supported
Transfer L4
Stop Light SW
Immobiliser Communication
Closed Throttle Position SW
TC Terminal
MIL ON Run Distance
Running Time from MIL ON
Time after DTC Cleared
Distance from DTC Cleared
Warmup Cycle Cleared DTC
Distance Traveled from Last Battery Cable Disconnect
IG OFF Elapsed Time
Soak IC Current Timer Value
Ignition Trigger Count
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6
All Cylinders Misfire Count
Misfire RPM
Misfire Load
Misfire Margin
Catalyst OT Misfire Fuel Cut
Catalyst OT Misfire Fuel Cut History
Catalyst OT Misfire Fuel Cut Cylinder #1
Catalyst OT Misfire Fuel Cut Cylinder #2
Catalyst OT Misfire Fuel Cut Cylinder #3
Catalyst OT Misfire Fuel Cut Cylinder #4
Catalyst OT Misfire Fuel Cut Cylinder #5
Catalyst OT Misfire Fuel Cut Cylinder #6
Engine Speed (Starter Off)
Starter Count
Run Distance of Previous Trip
Engine Starting Time
Engine Start Hesitation
Low Revolution for Engine Start
Fuel Cut Elapsed Time
Previous Trip Coolant Temp
Previous Trip Intake Temp
Engine Oil Temperature
Previous Trip Eng Oil Temp
Ambient Temp for A/C
Previous Trip Ambient Temp
A/F Learn Value Idle Bank 1
A/F Learn Value Idle Bank 2
A/F Learn Value Low Bank 1
A/F Learn Value Low Bank 2
A/F Learn Value Mid No.1 Bank 1
A/F Learn Value Mid No.1 Bank 2
A/F Learn Value Mid No.2 Bank 1
A/F Learn Value Mid No.2 Bank 2
A/F Learn Value High Bank 1
A/F Learn Value High Bank 2
Rough Idle Status
Plural Cylinders Rough Idle
Rough Idle Cylinder #1
Rough Idle Cylinder #2
Rough Idle Cylinder #3
Rough Idle Cylinder #4
Rough Idle Cylinder #5
Rough Idle Cylinder #6
Alternator Output Duty Ratio
Status of Alternator Temperature High
Alternator Voltage - Non Active Test
Voltage of Alternator
Brake Override System
Immobiliser Fuel Cut Status
Immobiliser Fuel Cut History
Fuel Cut Condition
Idle Fuel Cut
TAU Fuel Cut
Power Steering Pressure
Engine Speed Cylinder #1
Engine Speed Cylinder #2
Engine Speed Cylinder #3
Engine Speed Cylinder #4
Engine Speed Cylinder #5
Engine Speed Cylinder #6
Average Engine Speed of All Cylinder
NT Sensor Speed
Speed (SP2)
SP2 Sensor Voltage
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (N,P Range)
Shift SW Status (N,P Range) Supported
Sport Shift Up SW
Sport Shift Down SW
Shift SW Status (S Range)
Snow Mode SW
Shift SW Status (D Range)
A/T Oil Temperature No.1
A/T Oil Temperature No.2
ATF Thermal Degradation Estimate
Torque Converter Temperature Raise History
NT Sensor Voltage
Drive Mode Status
Endless Rotary Switch (Phase A)
Endless Rotary Switch (Phase B)
Power Mode SW
Lock Up Status
Shift Status
Solenoid (SLT)
Solenoid (SLU)
Solenoid (SL)
Snow or 2nd Start Mode Status