Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM U

1GR-FE ENGINE CONTROL  SFI SYSTEM  FAIL-SAFE CHART  


If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.

DTC Code Component Fail-Safe Operation Fail-Safe Deactivation Condition
P001100
P001500
P002100
P002500
VVT system
·

Idle up (control of combustion worsening).

·

Fuel-cut control is stopped.


Pass condition detected
P003012
P003013
P005012
P005013
P101A9E
P103A9E
Air fuel ratio sensor heater The ECM turns off the air fuel ratio sensor heater. Ignition switch off
P003612
P003614
P005612
P005614
P102A9E
P105A9E
Heated oxygen sensor heater The ECM turns off the heated oxygen sensor heater. Ignition switch off
P010012
P010014
Mass air flow meter sub-assembly The ECM calculates ignition timing according to the engine speed and throttle valve position. Pass condition detected
P011011
P011015
Intake air temperature sensor The ECM estimates the intake air temperature to be 20°C (68°F). Pass condition detected
P011511
P011515
Engine coolant temperature sensor The ECM estimates the engine coolant temperature to be 80°C (176°F). Pass condition detected
P012011
P012015
P01201C
P022011
P022015
P060444
P060604
P060629
P060647
P060A47
P060B49
P060D49
P060E49
P065714
P06579E
P160700
P210018
P210019
P211172
P211173
P211900
P211904
P211977
P21352B
Electronic throttle control system The ECM cuts off throttle actuator current and the throttle valve is returned to a 7° throttle position by the return spring.
The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal angle to allow the vehicle to continue at minimal speed*1.
Pass condition detected and then ignition switch turned off
P030000
P030027
P030085
P030100
P030200
P030300
P030400
P030500
P030600
*2
·

Fuel injector assembly

·

Electronic throttle control system


When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.
1.

Under a low load and at a low engine speed:

- Fuel-cut is performed on the malfunctioning cylinder.

2.

Under a high load and at a high engine speed:

- Throttle valve opening angle control is performed.

- Fuel-cut is performed on all cylinders or the malfunctioning cylinder.


Pass condition detected and then ignition switch turned off
P032511
P032515
P033011
P033015
Knock control sensor The ECM sets the ignition timing to maximum retard. Ignition switch off
P035113
P035213
P035313
P035413
P035513
P035613
Ignition coil assembly The ECM cuts the fuel injection. Pass condition detected
P05042B Stop light switch assembly The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction. Pass condition detected
P212012
P212014
P21201C
P21201F
P212099
P212512
P212514
P21251F
P21382B
Accelerator pedal position sensor The accelerator pedal position sensor has 2 sensor circuits: Main and Sub.
If there is a malfunction in either circuit, the ECM limits the engine output.
If there is a malfunction in both circuits, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Pass condition detected and then ignition switch turned off
P223711
P223712
P223713
P213716
P223717
P22371B
P224011
P224012
P224013
P224016
P224017
P22401B
P225111
P225112
P225411
P225412
Air fuel ratio sensor
·

Air fuel ratio feedback control is stopped.

·

Current to the air fuel ratio sensor heater is cut.


Pass condition detected and then ignition switch turned off
P243011
P243015
P243511
P243515
P244072
P244272
P24457F
Secondary air injecion system Throttle valve opening angle control is performed. Pass condition detected

HINT:

*1: The vehicle can be driven slowly if the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.

*2: Misfire-related fail-safe operations occur when catalyst overheat malfunctions occur.