Home › Steering › STEERING COLUMN › STEERING SYSTEM
RM38G0E _55 Steering _100923 STEERING COLUMN _0469197 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING WHEEL OFF CENTER ADJUSTMENT PROCEDURE

a.

Inspect steering wheel off center.

i.

Turn the steering wheel assembly to the center position.


ii.
C456053C01
0.99,0.76 0.438,0.281 0.438,0.281 0.833,0.948 true 1.5,0.521 1.583,0.25 1.583,0.25 1.667,0.25 true 1.083,1.083 1.854,1.51 true 0.313,0.125 0.625,0.323 0.313,0.198 10 false *a 1.74,0.156 2.052,0.354 0.313,0.198 10 false *1 1.938,1.458 2.25,1.656 0.313,0.198 10 true *2
*1 Steering Wheel Assembly
*2 Upper Steering Column Cover
*a Masking Tape


Apply masking tape to the top center of the steering wheel assembly and upper steering column cover.


iii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), while holding the steering wheel assembly to maintain the course.


iv.
C456054C01
1.542,0.656 0.802,0.26 0.802,0.26 1.521,0.385 true 2.229,0.188 2.646,0.188 true 0.615,0.885 0.802,1.052 true 1.667,0.677 2.74,0.781 2.74,0.781 1.677,0.448 true 0.625,0.177 0.938,0.375 0.313,0.198 10 false *a 2.625,0.156 2.938,0.354 0.313,0.198 10 false *1 0.469,0.719 0.781,0.917 0.313,0.198 10 false *2 2.781,0.719 3.094,0.917 0.313,0.198 10 false *b
*1 Upper Steering Column Cover
*2 Steering Wheel Assembly
*a Masking Tape
*b Marked Line


Draw a line on the masking tape as shown in the illustration.


v.

Turn the steering wheel assembly to the center position.

HINT:

Look at the upper surface of the steering wheel assembly, steering spoke and SRS airbag line to find the center position.



vi.
C456055C01
0.594,0.917 0.76,1.052 true 2.198,0.198 2.604,0.198 true 1.729,0.677 2.688,0.896 true 1.563,0.396 0.865,0.26 0.865,0.26 1.385,0.625 true 0.427,0.781 0.698,0.958 0.271,0.177 10 false *2 2.656,0.125 2.969,0.323 0.313,0.198 10 false *1 2.74,0.813 3.052,1.01 0.313,0.198 10 false *b 0.667,0.125 0.979,0.323 0.313,0.198 10 false *a
*1 Upper Steering Column Cover
*2 Steering Wheel Assembly
*a Masking Tape
*b Marked Line


Draw a new line on the masking tape on the steering wheel assembly as shown in the illustration.


vii.

Measure the distance between the 2 lines on the masking tape on the steering wheel assembly.


viii.

Convert the measured distance to the steering angle.

HINT:
·

Measured distance of 1 mm (0.0394 in.) = Steering angle of approximately 1 degree.

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C456056C01
1.083,1.198 1.125,1.615 1.125,1.615 1.281,1.198 true 1.073,1.656 1.385,1.813 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the tie rod assemblies LH and RH and steering rack end sub-assembly respectively.


ii.

Using a paper gauge, measure the thread length of the steering rack end sub-assemblies.

HINT:
·

Measure both RH and LH sides.

·

Make a note of the measured values.




iii.
C459967C01
1.021,2.5 1.094,2.906 1.094,2.906 1.26,2.906 true 2.031,2.729 2.344,2.885 0.313,0.156 10 false *a 0.844,1.854 1.156,2.01 0.313,0.156 10 false *b 0.5,3.021 0.729,3.219 0.229,0.198 10 false *c 1.313,2.833 1.792,3.083 0.479,0.25 10 false SST
*a Torque Wrench Fulcrum Length
*b Length of 131.5 mm (5.177 in.)
*c 30 mm (1.18 in.)


Remove the steering rack boot clips from the RH and LH No. 1 steering rack boots.


iv.

Loosen the RH and LH nuts.


v.

Turn the RH and LH steering rack end sub-assemblies by the same amount (but in different directions) according to the measured steering angle.

HINT:

1 turn (360°) of the rack end (1.5mm horizontal movement) is equivalent to a steering angle of 12°.



vi.

Using SST, tighten the RH and LH lock nuts to the specified torque.

SST
09922-10010  

Torque:
Specified tightening torque : 90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:

Adjust so the difference between the right and left tie rod ends and rack end screws are within 1.5 mm.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 131.5 mm (5.177 in.)) + torque wrench (fulcrum length of 255 mm (10.039 in.)): 59.4 N*m (606 kgf*cm, 44 ft.*lbf)




vii.

Install the RH and LH steering rack boot clips.