Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Rear Blower Motor Circuit  


DESCRIPTION

The rear blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly.

If the airflow volume is low or the blower speed cannot be changed, the following factors may be the cause.

Symptom Factor
Airflow volume cannot be changed
·

Air conditioning amplifier assembly malfunction

·

Rear blower motor with fan sub-assembly malfunction

·

Blower motor control malfunction

·

Harness or connector



WIRING DIAGRAM

E330395E08
5.958,1.396 6.479,1.573 0.521,0.177 10 false SBLW 5.698,1.302 5.938,1.479 0.24,0.177 10 false 10 5.771,1.938 6.01,2.115 0.24,0.177 10 false 4 3.969,0.667 4.208,0.844 0.24,0.177 10 false 1 4.25,0.927 5.25,1.104 1,0.177 10 false A/C RR 5.125,0.75 6.125,0.927 1,0.177 10 false from Battery 3.979,1.302 4.219,1.479 0.24,0.177 10 false 8 3.979,1.938 4.219,2.115 0.24,0.177 10 false 4 1.854,0.656 2.094,0.833 0.24,0.177 10 false 1 1.854,1.292 2.094,1.469 0.24,0.177 10 false 3 1.854,1.917 2.094,2.094 0.24,0.177 10 false 6 1.854,2.573 2.094,2.75 0.24,0.177 10 false 2 1.906,2.896 2.177,3.281 0.271,0.385 10 false Q76 2.094,2.583 2.333,2.76 0.24,0.177 10 false 2 2.813,2.583 3.052,2.76 0.24,0.177 10 false 1 1.885,3.073 3.302,3.479 1.417,0.406 10 false Rear Blower with Fan Motor Sub-assembly 1.792,3.708 3.573,4.115 1.781,0.406 10 false No. 1 Cooler Wiring Harness Sub-assembly 0.146,3.5 1.531,3.729 1.385,0.229 10 false Q75 0.135,3.656 1.521,3.885 1.385,0.229 10 false Blower Motor Control 5.542,2.427 6.927,2.656 1.385,0.229 10 false I31 5.542,2.594 7.156,3.031 1.615,0.438 10 false Air Conditioning Amplifier Assembly 5.958,2.031 6.479,2.25 0.521,0.219 10 false GND2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Blower Level Rear blower motor with fan sub-assembly operation 0 to 31 -
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Blower Level
50004 450 2

Result:
Result Proceed to
Rear blower motor with fan sub-assembly does not operate A
Rear blower motor with fan sub-assembly operates but does not change speed B



A

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - BATTERY AND BODY GROUND)

B

6.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
E330396C02
0.073,0.052 0.385,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 1 Cooler Wiring Harness Sub-assembly)


Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Disconnect the I31 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I31)Location & Routing

Click Connector(I31)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

8 - I31-10 (SBLW) Always Below 1 Ω
8 or I31-10 (SBLW)- Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Disconnect the I31 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I31)Location & Routing

Click Connector(I31)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

I31-10 (SBLW) - Body ground Always 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY

NG

REPLACE REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY

5.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY
a.

Replace the No. 1 cooler wiring harness sub-assembly with a new or known good one and check that the condition returns to normal.

OK:

Same problem does not occur.



Result:
Proceed to
OK
NG



OK

END (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY WAS DEFECTIVE)

NG

6.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
6.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E459652C01
0.583,0.656 1,0.906 0.417,0.25 0.083,0.073 0.438,0.323 0.354,0.25 10 false *a 0.667,0.698 1.021,0.948 0.354,0.25 10 false Q75 2.885,2.802 3.24,3.052 0.354,0.25 10 false GND
*a Component with harness connected
(Blower Motor Control)


Using an oscilloscope, check the waveform.

Tester Connection Tool Setting Condition

Click Location & Routing(Q75)Location & Routing

Click Connector(Q75)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blower Motor Control

Q75-3 - Body ground 1 V/DIV., 500 μs./DIV.
·

Ignition switch ON

·

Blower speed: LO



HINT:

The waveform varies with the blower speed.


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

7.CHECK BLOWER MOTOR CONTROL

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

7.CHECK BLOWER MOTOR CONTROL
a.

Replace the blower motor control with a new or known good one and check that the condition returns to normal.

OK:

Same problem does not occur.



Result:
Proceed to
OK
NG



OK

END (BLOWER MOTOR CONTROL WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY