WIRELESS CHARGER FUNCTION OUTLINE
The wireless charging system allows Qi-compatible* devices to be charged without connecting a charging cable by placing compatible devices on the charging area in the charging tray of the mobile wireless charger cradle assembly to activate the charging coil.
*: Qi-compatible is an international wireless charging standard set by the Wireless Power Consortium (WPC). The wireless charging system is compatible with Power Class 0 as defined by Qi-compatible Ver. 1.2.4 and supports charging from 5 W up to 10 W.
Qi-compatible devices which do not fit within the charging area cannot be used. If a Qi-compatible device does not operate normally, refer to the owner's manual of the device.
Qi-compatible rechargeable devices can be charged.
"Qi" and "Qi" logo are trademarks of the Wireless Power Consortium (WPC).
Although the wireless charging system meets Qi standards, compatibility with all Qi-compatible devices is not guaranteed.
CHARGING INDICATOR STATUS
| *a | Mobile Wireless Charger Switch |
| *b | Indicator Light (Green/Amber) |
| *c | Charging Tray |
| *d | Charging Area |
| *e | Approximately 70 mm (2.756 in.) |
| *f | Approximately 60 mm (2.362 in.) |
The indicator light shows the operation condition of the wireless charging system.
| Indicator | Operation Condition | |
|---|---|---|
| Condition | Color | |
| Off | - | Wireless charging system is turned off |
| On | Green |
·
Wireless charging system is on (standby)
·
Charging is complete*1 |
| On | Amber |
·
A rechargeable device is placed on the charging area
·
A rechargeable device is being charged |
| On (For 4.5 sec)*2 |
Green | Charging is stopped temporarily due to a charging suspension signal being received from the smart key system |
| Blinks (Pattern 1)*3 |
Amber | An open in the charging suspension signal circuit is detected |
| Blinks (Pattern 2)*3 |
Amber | The charging frequency is being changed |
| Blinks (Pattern 3)*3 |
Amber |
·
A flat object or small item with a thickness of 2.0 mm (0.079 in.) or more is detected between the charging area and the compatible device
·
A flat object or gap with a thickness of 2.0 mm (0.079 in.) or more is detected between the charging area and the compatible device
·
The rechargeable device is not placed correctly on the charging area
·
The rechargeable device has been moved from the position where it was first placed |
| Blinks (Pattern 4)*3 |
Amber | The temperature of the mobile wireless charger cradle assembly is abnormally high |
| On (Fast charging pattern)*3 |
Alternates between Green/Amber | Charging compatible device (fast charging) |
*1: Some mobile devices, cases or accessories may not cause the indicator (green) to illuminate when charging is complete even though they are Qi-compatible. Check the mobile device to confirm the charge status.
*2: If the charging suspension signal is received for less than 4.5 seconds, the indicator light (green) will remain illuminated for 4.5 seconds.
*3: Refer to the following diagram for details about the indicator blinking patterns.
RESUMPTION OF CHARGING
After charging is complete, if the rechargeable device is left in the same position on the charging area, charging will resume after 30 minutes elapse.
Charging will resume if the rechargeable device is moved or repositioned within the charging area, or replaced with another rechargeable device within 30 minutes of charging being completed.
If the rechargeable device is moved while it is being charged, charging will resume when the device is placed on the charging area.
If charging is stopped and resumed repeatedly due to the rechargeable device being moved or a communication error between the wireless charging system and rechargeable device, charging will be prohibited after a certain number of times to protect the rechargeable device.
Fast charging will be canceled if the position of the compatible device is adjusted during fast charging, as the system will assume that the compatible device has been replaced.
SUSPENSION OF CHARGING DUE TO THE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
The certification ECU (smart key ECU assembly) sends the charging suspension signal when any of the following conditions is met:
A door is opened and closed.
The back door opening switch is pressed.
The back door is closed.
The engine is started.
An electrical key transmitter sub-assembly is not detected in the cabin.
When charging is suspended due to the charging suspension signal, the indicator (green) will illuminate.
If there is an open in the charging suspension signal circuit, the indicator (amber) will blink (pattern 1).
CHARGING FREQUENCY SWITCHING FUNCTION
If noise is generated in the AM radio during charging, turn the wireless charging system off and check if the noise is reduced. If the noise is reduced, press and hold the mobile wireless charger switch for approximately 2 seconds to change the charging frequency and reduce the noise.
When the charging frequency is being changed, the indicator (amber) blinks (pattern 2).
Fast charging is canceled on some mobile devices when the charging frequency is changed during fast charging.