Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0469303 TRANSFER ASSEMBLY G

JF2BM TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  INSPECTION  


PROCEDURE

Hide 36211 1.INSPECT TRANSFER INPUT SHAFT

a.
C456622

Using a micrometer, measure the diameter of the input shaft journal surface.

Minimum Diameter:

61.002 mm (2.40 in.)


If the diameter is less than the minimum, replace the transfer input shaft.


b.
C456623

Using a dial indicator, measure the inside diameter of the input shaft bush.

Maximum Inside Diameter:

46.025 mm (1.81 in.)


If the inside diameter is more than the maximum, replace the transfer input shaft.


Hide 36270 2.INSPECT TRANSFER LOW PLANETARY GEAR ASSEMBLY

a.
C456624

Using a feeler gauge, measure the thrust clearance of the pinion gear.

Standard Clearance:

0.11 to 0.85 mm (0.00434 to 0.0334 in.)


Maximum Clearance:

0.85 mm (0.0334 in.)


If the clearance is more than the maximum, replace the transfer low planetary gear assembly.


b.
C456625

Using a dial indicator, measure the radial clearance of the pinion gear.

Standard Clearance:

0.017 to 0.044 mm (0.000670 to 0.001732 in.)


Maximum Clearance:

0.044 mm (0.001732 in.)


If the clearance is more than the maximum, replace the transfer low planetary gear assembly.


Hide 36231 3.INSPECT REAR TRANSFER OUTPUT SHAFT

a.
C456626N01
0.802,0.573 0.969,0.76 0.167,0.188 10 false A 1.479,0.542 1.646,0.719 0.167,0.177 10 false B 1.979,0.531 2.156,0.729 0.177,0.198 10 false C 0.313,0.604 0.469,0.802 0.156,0.198 10 false D

Using a micrometer, measure the diameter of the rear transfer output shaft journals.

Minimum Diameter:
Journal Specified Condition
A 37.984 mm (1.50 in.)
B 41.984 mm (1.65 in.)
C 48.984 mm (1.93 in.)
D 31.980 mm (1.26 in.)


If the diameter is less than the minimum, replace the rear transfer output shaft.


Hide 36205 4.INSPECT TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.
C456629

Using a feeler gauge, measure the thrust clearance.

Standard Clearance:

0.10 to 0.56 mm (0.00394 to 0.02204 in.)


Maximum Clearance:

0.56 mm (0.02204 in.)


If the thrust clearance is more than the maximum, replace the transfer drive sprocket sub-assembly.


b.
C456630

Using a dial indicator, measure the radial clearance between the transfer drive sprocket sub-assembly and rear transfer output shaft with the transfer output shaft rear radial ball bearing installed.

Standard Radial Clearance:

0.015 to 0.068 mm (0.000591 to 0.002677 in.)


Maximum Radial Clearance:

0.068 mm (0.002677 in.)


If the radial clearance is more than the maximum, replace the transfer drive sprocket sub-assembly or transfer output shaft rear radial ball bearing.


Hide 36106L 5.INSPECT TRANSFER OIL PUMP ROTOR SET

a.

Apply transfer oil to the transfer oil pump rotor set.


b.
C458267C01
1.479,1.208 1.167,1.813 1.167,1.813 1.625,1.302 true 0.99,1.771 1.219,1.979 0.229,0.208 10 false *a
*a Mark


Install the oil pump drive rotor and oil pump driven rotor to the front transfer case with the marks facing the rear transfer case side. Check that it turns smoothly.


c.

Check the body clearance.

i.
C458232

Using a feeler gauge, measure the clearance between the body of the oil pump driven rotor and front transfer case.

Standard Body Clearance:

0.09 to 0.16 mm (0.00355 to 0.00629 in.)


Maximum Body clearance:

0.16 mm (0.00629 in.)


If the clearance is more than the maximum, replace the transfer oil pump rotor set and front transfer case.



d.

Check the tip clearance.

i.
C458233

Using a feeler gauge, measure the clearance between the tips of the oil pump drive rotor and oil pump driven rotor.

Standard Tip Clearance:

0.04 to 0.16 mm (0.00158 to 0.00629 in.)


Maximum Tip Clearance:

0.16 mm (0.00629 in.)


If the tip clearance is more than the maximum, replace the transfer oil pump rotor set.



e.

Check the side clearance.

i.
C458234

Using a feeler gauge, measure the clearance between the side of the transfer oil pump rotor set and front transfer case.

Standard Side Clearance:

0.03 to 0.10 mm (0.00119 to 0.00393 in.)


Maximum Side Clearance:

0.10 mm (0.00393 in.)


If the clearance is more than the maximum, replace the transfer oil pump rotor set and front transfer case.



Hide 36227 6.INSPECT TRANSFER OIL PUMP GEAR ROTATION

a.

Apply transfer oil to the transfer oil pump rotor set.


b.
C458267C01
1.479,1.208 1.167,1.813 1.167,1.813 1.625,1.302 true 0.99,1.771 1.219,1.979 0.229,0.208 10 false *a
*a Mark


Install the oil pump drive rotor and oil pump driven rotor to the front transfer case with the marks facing the rear transfer case side.


c.
C458268

Install the oil pump shaft to the front transfer case.


d.
C458235C01
0.896,0.698 1.052,0.896 0.156,0.198 10 false -
V113147

Rotates Smoothly


Install the oil pump gear to the oil pump shaft. Check that the transfer oil pump gear rotates smoothly.

If the oil pump gear does not rotate smoothly, replace the transfer oil pump rotor set.


Hide 36311F 7.INSPECT NO. 1 TRANSFER GEAR SHIFT FORK AND FRONT DRIVE CLUTCH SLEEVE CLEARANCE

a.
C456627

Using a feeler gauge, measure the clearance between the No. 1 transfer gear shift fork and front drive clutch sleeve.

Maximum Clearance:

0.84 mm (0.0331 in.)


If the clearance is more than the maximum, replace the No. 1 transfer gear shift fork and front drive clutch sleeve.


Hide 36312F 8.INSPECT NO. 2 TRANSFER GEAR SHIFT FORK AND TRANSFER HIGH AND LOW CLUTCH SLEEVE CLEARANCE

a.
C456628

Using a feeler gauge, measure the clearance between the No. 2 transfer gear shift fork and transfer high and low clutch sleeve.

Maximum Clearance:

3.40 mm (0.134 in.)


If the clearance is more than the maximum, replace the No. 2 transfer gear shift fork and transfer high and low clutch sleeve.


Hide 36410J 9.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (HIGH-LOW TRANSFER SHIFT ACTUATOR)

a.

Check the high-low transfer shift actuator.

i.

Check the high to low switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the high to low position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the relay.

Part number: 90987-04010


C453520C01
0.396,2.781 0.76,3 0.365,0.219 0.719,3.573 0.927,3.573 0.927,3.573 1.083,3.281 true 1.146,3.583 1.146,3.448 1.146,3.448 1.25,3.281 true 1.479,3.573 1.479,3.438 1.479,3.438 1.417,3.281 true 1.99,3.531 1.781,3.531 1.781,3.531 1.594,3.292 true 1.802,3.219 2.24,3.219 true 5.354,1.917 5.719,1.917 5.719,1.917 6.042,2.24 true 6.458,2.594 6.75,2.594 true 6.042,3.354 6.042,2.969 true 6.125,2.573 6.615,1.99 6.615,1.99 6.792,1.99 true 5.146,2.844 5.396,2.844 5.396,2.844 5.75,2.594 true 0.51,3.208 0.865,3.208 true 0.198,3.146 0.51,3.344 0.313,0.198 10 false GND 0.448,3.51 0.74,3.708 0.292,0.198 10 false HL2 1.031,3.594 1.333,3.792 0.302,0.198 10 false HL3 1.396,3.594 1.698,3.781 0.302,0.188 10 false HL1 2.031,3.458 2.375,3.646 0.344,0.188 10 false HM2 2.281,3.156 2.625,3.344 0.344,0.188 10 false HM1 5.948,1.635 6.219,1.885 0.271,0.25 10 false *1 0.25,0.115 0.531,0.375 0.281,0.26 10 false *a 0.26,2.49 0.51,2.677 0.25,0.188 10 false *b 5.229,1.844 5.365,2.042 0.135,0.198 10 false 1 6.01,3.375 6.167,3.573 0.156,0.198 10 false 2 5.01,2.781 5.146,2.979 0.135,0.198 10 false 3 6.823,1.917 6.979,2.115 0.156,0.198 10 false 4 6.792,2.531 6.948,2.729 0.156,0.198 10 false 5 2.885,1.677 3.115,1.906 0.229,0.229 10 false *1 0.458,2.823 0.792,3 0.333,0.177 10 false C48
*1 Relay - -
*a High → Low *b Component without harness connected
(High-Low Transfer Shift Actuator)


2.

After the high to low switch is complete, check the neutral position detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C48)Location & Routing

Click Connector(C48)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transfer Assembly

C48-3 (HL1) - C48-6 (GND) After high to low switch is complete 10 kΩ or higher
C48-4 (HL3) - C48-6 (GND) After high to low switch is complete 10 kΩ or higher
C48-5 (HL2) - C48-6 (GND) After high to low switch is complete Below 1 Ω


If the result is not as specified, replace the transfer shift actuator assembly.




ii.

Check the low to high switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the low to high position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the relay.

Part number: 90987-04010


C453521C01
0.333,2.792 0.708,3.01 0.375,0.219 0.552,3.219 0.854,3.219 true 1.823,3.208 2.177,3.208 true 0.854,3.469 1.01,3.469 1.01,3.469 1.083,3.281 true 1.125,3.552 1.125,3.448 1.125,3.448 1.25,3.271 true 1.531,3.563 1.531,3.479 1.531,3.479 1.427,3.271 true 1.615,3.271 1.76,3.458 1.76,3.458 1.948,3.458 true 5.49,1.896 5.76,1.896 5.76,1.896 6.052,2.25 true 6.031,3.396 6.031,2.969 true 5.198,2.906 5.385,2.906 5.385,2.906 5.75,2.594 true 6.115,2.594 6.583,1.979 6.583,1.979 6.75,1.979 false 6.448,2.583 6.823,2.583 true 0.24,3.156 0.563,3.354 0.323,0.198 10 false GND 0.573,3.406 0.854,3.604 0.281,0.198 10 false HL2 1.021,3.563 1.375,3.76 0.354,0.198 10 false HL3 1.438,3.573 1.792,3.771 0.354,0.198 10 false HL1 1.99,3.385 2.344,3.583 0.354,0.198 10 false HM2 2.229,3.135 2.583,3.333 0.354,0.198 10 false HM1 5.365,1.823 5.521,2.021 0.156,0.198 10 false 1 6,3.417 6.156,3.615 0.156,0.198 10 false 2 5.073,2.844 5.229,3.042 0.156,0.198 10 false 3 6.792,1.917 6.948,2.115 0.156,0.198 10 false 4 6.854,2.51 7.01,2.708 0.156,0.198 10 false 5 5.948,1.646 6.229,1.844 0.281,0.198 10 false *1 0.104,0.073 0.385,0.281 0.281,0.208 10 false *a 0.198,2.479 0.438,2.698 0.24,0.219 10 false *b 2.885,1.667 3.167,1.865 0.281,0.198 10 false *1 0.396,2.833 0.719,3.01 0.323,0.177 10 false C48
*1 Relay - -
*a Low → High *b Component without harness connected
(High-Low Transfer Shift Actuator)


2.

After the low to high switch is complete, check the neutral position detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C48)Location & Routing

Click Connector(C48)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transfer Assembly

C48-3 (HL1) - C48-6 (GND) After low to high switch is complete Below 1 Ω
C48-4 (HL3) - C48-6 (GND) After low to high switch is complete 10 kΩ or higher
C48-5 (HL2) - C48-6 (GND) After low to high switch is complete 10 kΩ or higher


If the result is not as specified, replace the transfer shift actuator assembly.





Hide 36410J 10.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (CENTER DIFFERENTIAL LOCK ACTUATOR)

a.

Check the center differential lock actuator.

i.

Check the free to lock switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the free to lock position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the relay.

Part number: 90987-04010


C453522C01
0.479,2.74 0.896,2.979 0.417,0.24 0.479,3.219 0.854,3.219 true 1.813,3.208 2.188,3.208 true 0.74,3.479 0.917,3.479 0.917,3.479 1.083,3.271 true 1.135,3.552 1.135,3.448 1.135,3.448 1.25,3.271 true 1.5,3.563 1.5,3.458 1.5,3.458 1.427,3.281 true 1.594,3.281 1.771,3.479 1.771,3.479 1.906,3.479 true 5.427,1.917 5.635,1.917 5.635,1.917 6.052,2.25 true 5.25,2.875 5.417,2.875 5.417,2.875 5.75,2.594 true 6.031,3.396 6.031,2.969 true 6.448,2.594 6.75,2.594 true 6.115,2.594 6.615,1.885 6.615,1.885 6.823,1.885 true 0.198,3.146 0.479,3.344 0.281,0.198 10 false TL2 0.458,3.417 0.75,3.625 0.292,0.208 10 false TL3 0.958,3.583 1.354,3.792 0.396,0.208 10 false GND1 1.396,3.583 1.708,3.771 0.313,0.188 10 false CDL 1.958,3.406 2.302,3.615 0.344,0.208 10 false TM2 2.219,3.146 2.563,3.354 0.344,0.208 10 false TM1 5.281,1.854 5.438,2.052 0.156,0.198 10 false 1 6,3.417 6.156,3.615 0.156,0.198 10 false 2 5.115,2.813 5.271,3.01 0.156,0.198 10 false 3 6.865,1.823 7.021,2.021 0.156,0.198 10 false 4 6.792,2.521 6.948,2.719 0.156,0.198 10 false 5 2.865,1.646 3.104,1.833 0.24,0.188 10 false *1 0.156,0.115 0.469,0.375 0.313,0.26 10 false *a 0.188,2.542 0.427,2.771 0.24,0.229 10 false *b 5.958,1.667 6.24,1.885 0.281,0.219 10 false *1 0.563,2.802 0.885,2.99 0.323,0.188 10 false C47
*1 Relay - -
*a Free → Lock *b Component without harness connected
(Center Differential Lock Actuator)


2.

After the free to lock switch is complete, check the center differential lock detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C47)Location & Routing

Click Connector(C47)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transfer Assembly

C47-3 (CDL) - C47-4 (GND1) After free to lock switch is complete Below 1 Ω
C47-5 (TL3) - C47-4 (GND1) After free to lock switch is complete 10 kΩ or higher
C47-6 (TL2) - C47-4 (GND1) After free to lock switch is complete Below 1 Ω


If the result is not as specified, replace the transfer shift actuator assembly.




ii.

Check the lock to free switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the lock to free position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the relay.

Part number: 90987-04010


C453523C01
0.396,2.792 0.802,3.01 0.406,0.219 0.552,3.219 0.865,3.219 true 1.813,3.208 2.125,3.208 true 0.75,3.458 0.948,3.458 0.948,3.458 1.083,3.281 true 1.615,3.271 1.865,3.438 1.865,3.438 2.021,3.438 true 1.146,3.573 1.146,3.438 1.146,3.438 1.25,3.271 true 1.521,3.573 1.521,3.438 1.521,3.438 1.438,3.271 true 5.396,1.927 5.646,1.927 5.646,1.927 6.052,2.25 true 6.031,3.344 6.031,2.969 true 6.458,2.583 6.813,2.583 true 5.229,2.885 5.406,2.885 5.406,2.885 5.75,2.594 true 6.125,2.583 6.583,1.906 6.583,1.906 6.75,1.906 true 0.271,3.146 0.563,3.344 0.292,0.198 10 false TL2 0.479,3.396 0.771,3.594 0.292,0.198 10 false TL3 0.969,3.594 1.375,3.792 0.406,0.198 10 false GND1 1.427,3.594 1.781,3.781 0.354,0.188 10 false CDL 2.052,3.365 2.406,3.563 0.354,0.198 10 false TM2 2.156,3.146 2.49,3.344 0.333,0.198 10 false TM1 5.271,1.854 5.406,2.063 0.135,0.208 10 false 1 6,3.354 6.156,3.552 0.156,0.198 10 false 2 5.094,2.813 5.24,3.021 0.146,0.208 10 false 3 6.792,1.833 6.948,2.031 0.156,0.198 10 false 4 6.854,2.521 7.01,2.719 0.156,0.198 10 false 5 5.948,1.615 6.208,1.802 0.26,0.188 10 false *1 0.115,0.104 0.375,0.354 0.26,0.25 10 false *a 0.167,2.615 0.406,2.813 0.24,0.198 10 false *b 2.896,1.667 3.156,1.854 0.26,0.188 10 false *1 0.479,2.833 0.813,3.01 0.333,0.177 10 false C47
*1 Relay - -
*a Lock → Free *b Component without harness connected
(Center Differential Lock Actuator)


2.

After the lock to free switch is complete, check the center differential lock detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C47)Location & Routing

Click Connector(C47)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transfer Assembly

C47-3 (CDL) - C47-4 (GND1) After lock to free switch is complete 10 kΩ or higher
C47-5 (TL3) - C47-4 (GND1) After lock to free switch is complete Below 1 Ω
C47-6 (TL2) - C47-4 (GND1) After lock to free switch is complete 10 kΩ or higher


If the result is not as specified, replace the transfer shift actuator assembly.