Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall)
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0467508 TELEMATICS SYSTEM(for eCall) D

TELEMATICS  TELEMATICS SYSTEM(for eCall)  SYSTEM DESCRIPTION  


DESCRIPTION


a.

eCall provides 2 services: Automatic Emergency Call and Manual Emergency Call.

If the vehicle is involved in an accident, the telematics system will make an automatic emergency call to a Public Safety Answering Point (PSAP) and transmit the vehicle location, determined by a GNSS satellite, and vehicle information. After receiving an emergency call from the vehicle, depending on the situation, a PSAP operator may immediately contact emergency services.

Y178726C01
4.802,5.906 5.115,6.104 0.313,0.198 10 false *a 3.271,3.927 3.583,4.125 0.313,0.198 10 false *b 5.635,4.438 5.948,4.635 0.313,0.198 10 false *c 5.344,1.448 5.656,1.646 0.313,0.198 10 false *c 6.719,3.677 7.031,3.875 0.313,0.198 10 false *d 3.906,1.729 4.219,1.927 0.313,0.198 10 false *e 0.458,2.375 0.771,2.573 0.313,0.198 10 false *f 1.271,3.052 1.583,3.25 0.313,0.198 10 false *g 2.354,1.229 2.667,1.427 0.313,0.198 10 false *c 0.646,4.844 0.958,5.042 0.313,0.198 10 false *h 2.198,4.948 2.51,5.146 0.313,0.198 10 false *i 0.344,6.333 0.656,6.531 0.313,0.198 10 false *j
*a Emergency Call Service *b GNSS Satellite
*c Cellular Phone Line *d Cellular Phone Base Station
*e Mobile Network Operator (MNO) or Mobile Virtual Network Operator (MVNO) *f Public Safety Answering Point (PSAP)
*g Public Fixed Line *h Emergency Vehicle
*i Public safety authorities such as police or fire department *j The illustrations shown are examples only and may differ from the actual service.




FUNCTION OF MAIN COMPONENTS


Component Function

*1: w/ Navigation System or w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)

*2: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)

Map Light Assembly
·

Manual (SOS) Switch


Sends a switch signal to the telephone transceiver assembly when pressed. (When a manual emergency call is performed.)
LED Indicator Light Green
·

Illuminates for 2 seconds after the ignition switch is turned to ON and the manual (SOS) switch indicator (red) has illuminated for 10 seconds.

·

Turns on when the system is operating normally.

·

Blinks during an emergency call.

·

Blinks during test mode.

·

Blinks 5 times when entering test mode (the manual (SOS) switch indicator (green) blinks at the same time).


Red
·

Illuminates for 10 seconds after the ignition switch is turned to ON.

·

Blinks when an emergency call cannot be performed.

·

Turns off when the system is operating normally.

·

Illuminates when the mobilephone battery needs to be replaced.

·

Illuminates in diagnostic mode to indicate a DTC.

·

Illuminates in diagnostic mode to indicate a specific vehicle history (RoB).

·

Blinks 5 times when entering test mode (the manual (SOS) switch indicator (red) blinks at the same time).


Communication Telematics Box
·

Sends the voice signal to the telephone transceiver assembly.

·

Outputs voice signals received from the telephone transceiver assembly through a built-in speaker.

·

Checks for malfunctions in its built-in speaker and microphones when the ignition switch is turned to ON.

·

Checks for an open in the speaker and microphone circuits between it and the telephone transceiver assembly when the ignition switch is ON.


Navigation Antenna Assembly Telephone Antenna (Sub) Sends and receives data and voice signals used for emergency calls via a communication network. (Connect as sub)
Roof Antenna Assembly Telephone Antenna (Main) Sends and receives data and voice signals used for emergency calls via a communication network. (Connect as main)
GNSS Antenna Receives GNSS radio signals and sends them to the telephone transceiver assembly.
Telephone Transceiver Assembly
·

Uses the roof antenna assembly to send and receive data and voice signals used for emergency calls via a communication network.

-

Sends the received voice signal to the communication telematics box.

-

Receives the sent voice signal from the communication telematics box.

-

Sends a mute signal to the stereo component amplifier assembly*1 or radio and display receiver assembly*2. (The audio system is automatically muted during an emergency call.)

-

Sends vehicle location information to the PSAP.

-

Conducts self-diagnosis every time the ignition switch is turned to ON and after an automatic emergency call or manual emergency call is made.

-

Sends vehicle information signals to the service center.

-

Receives remote operation signals from the service center.



Mobilephone Battery
·

When an automatic emergency call is performed and the battery is damaged, provides power to the telephone transceiver assembly.

·

When a manual emergency call is made, is not used as the power source.


Airbag ECU Assembly Sends a collision signal to the telephone transceiver assembly. (An automatic emergency call is made.)


MAYDAY ID OUTLINE


a.

The telephone transceiver assembly functions as the emergency call service device to perform emergency calls.


b.

The telephone transceiver assembly has serial numbers (IMEI, ICCID) which can be used to identify the individual device when servicing.


c.

The IMEI and ICCID are printed on the label attached to the telephone transceiver assembly.



COMMUNICATION SYSTEM


a.

CAN Communication Outline

i.

The telematics system uses CAN communication between the telephone transceiver assembly and ECUs.




DIAGNOSTIC FUNCTION OUTLINE


a.

The telematics system has a diagnostic function (the result will be displayed on the GTS).