This DTC is stored when a communication telematics box signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B157213 | Microphone Circuit Open | Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON |
·
Telephone transceiver assembly
·
Communication telematics box
·
Harness or connector
·
Mayday wire |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System (for eCall).
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Clear the DTCs.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Disconnect the I55 telephone transceiver assembly connector.
Disconnect the d3 mayday wire connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I55,d3)Location & Routingewd_type=routing;type=c,c;code=I55,d3 Click Connector(d3)Body>No. 1 Roof Wire>Communication Telematics Boxewd_type=component;type=c;code=d3;pinno=1,3,9,6,10,11,5 |
||
| I55-8 (MCMD) - d3-1 (MCMD) | Always | Below 1 Ω |
| I55-18 (SP+) - d3-3 (SP+) | Always | Below 1 Ω |
| I55-34 (SP-) - d3-9 (SP-) | Always | Below 1 Ω |
| I55-24 (MICV) - d3-6 (MICV) | Always | Below 1 Ω |
| I55-5 (MCVD) - d3-10 (MIC1) | Always | Below 1 Ω |
| I55-6 (MCI+) - d3-11 (MCI2) | Always | Below 1 Ω |
| I55-7 (MCI-) - d3-5 (MCI-) | Always | Below 1 Ω |
| I55-8 (MCMD) or d3-1 (MCMD) - Body ground | Always | 10 kΩ or higher |
| I55-18 (SP+) or d3-3 (SP+) - Body ground | Always | 10 kΩ or higher |
| I55-34 (SP-) or d3-9 (SP-) - Body ground | Always | 10 kΩ or higher |
| I55-24 (MICV) or d3-6 (MICV) - Body ground | Always | 10 kΩ or higher |
| I55-5 (MCVD) or d3-10 (MIC1) - Body ground | Always | 10 kΩ or higher |
| I55-6 (MCI+) or d3-11 (MCI2) - Body ground | Always | 10 kΩ or higher |
| I55-7 (MCI-) or d3-5 (MCI-) - Body ground | Always | 10 kΩ or higher |
| I55-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Component without harness connected (Wire Harness) |
| *b | Component without harness connected (Communication Telematics Box) |
Disconnect the d3 wire harness connector.
Disconnect the P communication telematics box connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(d3)Location & Routingewd_type=routing;type=c;code=d3 Click Connector(d3)Body>No. 1 Roof Wire>Communication Telematics Boxewd_type=component;type=c;code=d3;pinno=1,3,9,6,10,11,5 |
||
| d3-1 (MCMD) - P-1 (MCMD) | Always | Below 1 Ω |
| d3-3 (SP+) - P-3 (SP+) | Always | Below 1 Ω |
| d3-9 (SP-) - P-8 (SP-) | Always | Below 1 Ω |
| d3-6 (MICV) - P-5 (MICV) | Always | Below 1 Ω |
| d3-10 (MIC1) - P-7 (MIC2+) | Always | Below 1 Ω |
| d3-11 (MCI2) - P-2 (MIC1+) | Always | Below 1 Ω |
| d3-5 (MCI-) - P-4 (MCI-) | Always | Below 1 Ω |
| d3-1 (MCMD) or P-1 (MCMD) - Body ground | Always | 10 kΩ or higher |
| d3-3 (SP+) or P-3 (SP+) - Body ground | Always | 10 kΩ or higher |
| d3-9 (SP-) or P-8 (SP-) - Body ground | Always | 10 kΩ or higher |
| d3-6 (MICV) or P-5 (MICV) - Body ground | Always | 10 kΩ or higher |
| d3-10 (MIC1) or P-7 (MIC2+) - Body ground | Always | 10 kΩ or higher |
| d3-11 (MIC2) or P-2 (MIC1+) - Body ground | Always | 10 kΩ or higher |
| d3-5 (MCI-) or P-4 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *a | Component with harness connected (Telephone Transceiver Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I55)Location & Routingewd_type=routing;type=c;code=I55 |
||
| I55-24 (MICV) - Body ground | Ignition switch ON | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I55)Location & Routingewd_type=routing;type=c;code=I55 |
||
| I55-7 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Replace the communication telematics box with a new or known good one.
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
Post-procedure1
None
A
B
Replace the telephone transceiver assembly with a new one.
| Proceed to |
|---|
| NEXT |
NEXT